Use and Care Manual M.C. Advantage - Low Bed Model: QD1000 Series Table of Contents: Important Safety Precautions ....2 Span Medical Products Canada Product Specifications ......7 4658 Ontario St. Unpacking and Assembly ....... 9 Beamsville, Ontario, Canada L3J 0T9 Operating Instructions......
ENCLOSURE PROTECTION TYPE - Protection against water sprayed from all directions. of a resident/patient. Exceeding the Maximum Patient Weight could result in bed instability, property damage, injury or death. NOTE: Refer to Span Academy on the Span America website for guidance on safe patient DOWN handling during bed ingress/egress. WARNING!
Page 3
Do not use any replacement parts or accessories not manufactured, below the mattress support level. Remove or lock-out hand control when using oxygen marketed or provided by Span Medical/MC Healthcare on any Span Medical/MC Healthcare administrating equipment. bed. Use of unapproved replacement parts may result in injury or death.
Emergency Power back-up battery Pack 24 V DC Battery (optional). Protection against splashing water IPX4. Span Medical Products Canada is available to work with customers to minimize the risk of patient Mass of bed 160 lbs without any accessories. entrapment.
Optional. Make sure that all parts are included prior to disposing of the packaging material and immediately report any patient helper bar. missing parts to Span Medical Products Canada Customer Service. Power Supply Cord HEAD BOARD To keep the power supply cord off the floor...
ASSEMBLY INSTRUCTIONS - continued ASSEMBLY INSTRUCTIONS - continued Bed Setup HEAD END Assembly of Baseboard Bumper M. C. Advantage bed is approved for operation in a dry environment. To operate the bed, plug the Power Supply Cord running from the patient left hand side of the frame into Tools Required: Rubber Mallet a three prong 120 V hospital grade wall receptacle.
ASSEMBLY INSTRUCTIONS - continued ASSEMBLY INSTRUCTIONS - continued Patient Helper /Trapeze- optional Pull spring pin up, rotate Head and Foot Board Mounting Bracket Assembly pole, and let spring pin drop into desired hole. The optional patient helper consists of brackets mounted to Tools Required: two 5/32"...
Page 8
ASSEMBLY INSTRUCTIONS - continued ASSEMBLY INSTRUCTIONS - continued FEC Assembly Head and Foot Board Assembly Tools Required: Philips Screw Driver Insert the Head and Foot Boards Parts (included): as illustrated with the proper Item # Description Mounting Bracket orientation. Control Pad with cable attached Rear Cover After the Boards are in place, Cable Cover...
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS Total Lock Casters Side rails All Side rails are optional. To engage the total lock casters, simply press down on the locking tab with LOCKED CASTER UNLOCKED CASTER your toe on all four casters. This will prevent any movement of the caster 1/2 Length Side rails (rolling or swiveling).
To lower Back Section, press and hold DOWN button. The back-up battery is replaceable. Replace only with battery provided by Span Medical Products Knee Deck Operation Canada. Please contact Span Customer Service for details. To raise Knee Section, press and hold UP button.
MAINTENANCE MAINTENANCE Cleaning RETAINING RINGS – All clevis pins must have retaining rings present. Replace any missing rings. All "Rue" type pins should be manually locked and visually inspected on a regular basis, as illustrated below. M.C. Advantage bed can be cleaned with warm water and a mild detergent or diluted disinfectant.
Department for assistance at 1-800-268- 8671. Do not ship any parts back to Span Parts that are found to be worn or defective should be replaced with new parts from Span Medical Medical Products Canada without an RMA QP3858 (120V) Products Canada.
For an RMA number, call Span Medical Products Canada - Customer Support , Tel #: 1-800-268-8671. Fax completed form to Span Medical Products Canada - Customer Support , Fax #: 1- 905-563-8680.
Warranty claim parts must be returned to Span for inspection and testing. If the claim parts are not returned in 45 days of the filing of the RMA, Span reserves the right to initiate a billing invoice for the replacement parts sent to the customer.
Need help?
Do you have a question about the M.C. Advantage QD1000 Series and is the answer not in the manual?
Questions and answers