Download
Share
Print this page
Kyocera TASKalfa 552ci Installation Manual
  1. Manuals
  2. Brands
  3. Kyocera Manuals
  4. Printer
  5. TASKalfa 552ci
  6. Installation manual
Kyocera TASKalfa 552ci Installation Manual

Kyocera TASKalfa 552ci Installation Manual

Document processor
Hide thumbs Also See for TASKalfa 552ci:

Advertisement

Quick Links

Download this manual
INSTALLATION GUIDE
INSTALLATION GUIDE FOR
DOCUMENT PROCESSOR
Output Connector for Interconnecting Cable is non-LPS.
Output: 587 VA max.
Please use the item below Interconnecting Cable/
P/N: 303LK46010, 303LL46010

Advertisement

loading
Need help?

Need help?

Do you have a question about the TASKalfa 552ci and is the answer not in the manual?

Questions and answers

Related Manuals for Kyocera TASKalfa 552ci

Summary of Contents for Kyocera TASKalfa 552ci

  • Page 1 INSTALLATION GUIDE INSTALLATION GUIDE FOR DOCUMENT PROCESSOR Output Connector for Interconnecting Cable is non-LPS. Output: 587 VA max. Please use the item below Interconnecting Cable/ P/N: 303LK46010, 303LL46010...
  • Page 2 G Label “Operation procedure” Precautions English (except for 100 V models) ....... 1 Be sure to remove any tape and/or cushioning Supplied parts *: for metric specification material from supplied parts. A DP............1 **: for inch specification B Original mat ..........1 H Caution label “Original face up!”...
  • Page 3 Procedure Attach the fixing fitting. Install the DP. When installing the DP, be sure to turn the 1. Align projections (1) of each fixing fitting (C) 3. Align hinge hole (3) of DP (A) with pin (4) of MFP power off and disconnect the power plug with holes (2) on the MFP and insert the fix- fixing fitting (C), place DP (A) on the MFP.
  • Page 4 5. Install DP (A) onto the MFP securely with pin Install the angle control fitting. To adjust DP open-close angle 30 degrees (E) and two M4 × 14TP screws (F). 7. Open the upper cover (6) of the DP (A). To adjust DP open-close angle 60 degrees 8.
  • Page 5 9. Remove stop ring (9) of angle control fitting 10.Insert shaft (10) into the rear side of the right 13.Move to: (D) that has been installed in step 6 to hinge. Step 14 when using DP-760 remove shaft (10). 11. Attach stop ring (9) to the notch of shaft (10) (full-color machines), or and secure shaft (10).
  • Page 6 YC10 Installing the DP relay PWB 16.Remove the screw (14) to remove the DP 17.Place connector (16) on the DP relay PWB cover (15) on the MFP. (I) through the rectangular hole (17). 14.Remove the filter cover (11) of the MFP. 18.Connect connector (YC2) on the DP relay 15.Remove nine screws (12) and then remove PWB (I) to connector (YC10) on the MFP.
  • Page 7 2mm 0mm 19.Secure the DP relay PWB (I) with two M2.6 x Installing the gasket 22.Replace the upper rear cover (13) of the 8 screws (J). MFP using nine screws (12). 20.Peel the release paper (18) off the gasket 23.Reinstall the filter cover (11) of the MFP. (K).
  • Page 8 YC10 Installing the DP relay PWB 25.Remove the screw (22) to remove the DP 26.Place connector (24) on the DP relay PWB cover (23) on the MFP. (I) through the rectangular hole (25). 24.Remove the screw (20) and then remove the 27.Connect connector (YC2) on the DP relay upper rear cover (21).
  • Page 9 28.Secure the DP relay PWB (I) with two M2.6 x Connect the signal lines. 8 screws (J). 30.Connect data signal line (26) on the DP (A) 29.Replace the upper rear cover (21) of the to connector (27) on the DP relay PWB (I). MFP using the screw (20).
  • Page 10 14 / 22 31.Confirm that the signal line is firmly connected to the connector and secure the connector cover Connect the signal lines. (28) with the screw (*14 / 22) removed in step *16 / 25. 32. Connect data signal line (29) on the DP (A) to * : Full-color machines / Monochrome machines the MFP.
  • Page 11 Fasten the original mat. 33.Place original mat (B) with its Velcro (30) upward over the contact glass. Align original mat (B) corner that has 90 degrees of angle with the inner left corner of the original instruction panel. 34.Close DP (A) and attach original mat (B) onto it with Velcro. Fixer la plaque d’original.
  • Page 12 Adhere the label (except for 100 V models) 36.Adhere Label “Operation procedure” (G) of 37.Adhere Caution label “Original face up!” (H) which the language corresponding to the of which the language corresponding to the 35.Clean the label on the DP upper cover with destination of the MFP onto the existing label destination of the MFP onto the label on the alcohol.
  • Page 13 20mm 20mm 20mm 20mm [Operation check] 1. To check the machine operation, prepare original (a) where 4 lines (b) are drawn 20 mm from the edges of the A3 sheet and 1 line (c) is drawn at its center. 2. Connect the power plug of the MFP into the wall outlet and turn the main power switch on. 3.
  • Page 14 Be sure to adjust in the following order. If not, the adjustment cannot be performed correctly. For checking the angle of leading edge, see page 14. <Reference value> Simplex copying: within ±3.0 mm; Duplex copying: within ±4.0 mm For checking the angle of trailing edge, see page 17. <Reference value>...
  • Page 15 3mm/4mm 3mm/4mm [Checking the angle of leading edge] 1. Check the horizontal gap between line (1) of original (a) and line (2) of copy example positions. If the gap exceeds the reference value, adjust the gap according to the following procedure. <Reference value>...
  • Page 16 Adjusting the DP 2. Loosen two M4 × 14TP screws (F) of right and left fixing fittings (C). 3. Turn adjusting screw (3) at the rear side of the right hinge to adjust the DP position. For copy example (d): Turn the adjusting screw counterclockwise and move the DP to the inner side. For copy example (e): Turn the adjusting screw clockwise and move the DP to the front side.
  • Page 17 3mm/4mm 3mm/4mm 5. Repeat the steps above until the gap of line (2) of copy example shows the following reference values. <Reference value> For single copying: The horizontal gap of line (2) should be within ±3 mm. For duplex copying: The horizontal gap of line (2) should be within ±4 mm. 6.
  • Page 18 3mm/4mm 3mm/4mm [Checking the angle of trailing edge] 1. Check the gap between line (1) of original (a) and line (2) of copy example. If the gap exceeds the reference value, perform the following adjust- ment. <Reference value> For simplex copying: Within ±3.0 mm For duplex copying: Within ±4.0 mm [Vérification de l’angle du bord arrière] 1.
  • Page 19 Adjusting the DP 3. Adjust the height of DP. Loosen the nut (6). 2. Open the upper cover (3) of the DP (A). For copy example (f): Loosen the adjusting screw (7). Remove four screws (4) to remove the rear For copy example (g): Tighten the adjusting screw (7).
  • Page 20 3mm/4mm 3mm/4mm 6. Make a proof copy again. 7. Repeat steps 1 to 6 until line (2) of copy example shows the following the reference values. <Reference value> For simplex copying: Within ±3.0 mm For duplex copying: Within ±4.0 mm 6.
  • Page 21 -1.5% +1.5% [Checking the magnification] Adjusting the DP magnification * : Full-color machines / Monochrome machines 1. Check the gap between line (1) of original (a) and line (2) (3) of copy 2. Use the maintenance mode U070 to adjust the magnification. example.
  • Page 22 -1.5% +1.5% 3. Adjust the values. 5. Repeat the steps 2 to 4 above until the gap of line (2) (3) of copy exam- For the shorter length copy example (h)(j): Increases the value. ple shows the reference value. For the longer length copy example (i)(k): Decreases the value. <Reference value>...
  • Page 23 2.5mm 2.5mm [Checking the leading edge timing] Adjusting the DP leading edge timing * : Full-color machines / Monochrome machines 1. Check the gap between line (1) on original 2. Use the maintenance mode U071 to adjust the timing. (a) and line (2) of copy example. If the gap For the front page, adjust * ADJUST DATA1 / FRONT HEAD.
  • Page 24 2.5mm 2.5mm 3. Adjust the values. For the faster leading edge timing, copy examples (l): Decreases the value. For the slower leading edge timing, copy examples (m): Increases the value. Amount of change per step: 0.17 mm 4. Perform a test copy. 5.
  • Page 25 2mm/3mm 2mm/3mm [Checking the center line] 1. Check the gap between center line (1) on original (a) and center line (2) of copy example. If the gap exceeds the reference value, adjust the gap according to the following procedure. <Reference value> Horizontal difference of center line (2) for the single copying: ±2 mm Horizontal difference of center line (2) for the duplex copying: ±3 mm [Vérification de la ligne médiane] 1.
  • Page 26 2mm/3mm 2mm/3mm Adjusting the DP center line * : Full-color machines / Monochrome machines 2. Use the maintenance mode U072 to adjust the center line. For the front page, adjust * ADJUST DATA1 / FRONT. For the back page of the reverse duplex, adjust * ADJUST DATA2 / BACK. For the back page of the dual scan (CIS reading), adjust * ADJUST DATA3 / CIS.
  • Page 27 2mm/3mm 2mm/3mm 3. Adjust the values. If the center moves more front, copy example (n): Increases the value. If the center moves inner, copy sample (o): Decreases the value. Amount of change per step: 0.085 mm 4. Perform a test copy. 5.
  • Page 28 149 1mm A(149 5mm) 74 1mm [Automatic adjustment using the original for adjustment] 1. Direct F and R of the DP auto adjustment original upward, and set the original from the place where F and R are marked. 2. Set the maintenance mode U411. Press the DP (FACE UP) key, the INPUT key and the START key in order to adjust the surface. 3.
  • Page 29 149 1mm A(149 5mm) 74 1mm 4. After completing the surface adjustment, direct F and R of the DP auto adjustment original downward and set the original by inserting the side where the F and R are marked into the DP first. 5.

  • Page 30: Paper Feeder

    INSTALLATION GUIDE FOR PAPER FEEDER...
  • Page 31 F Stopper R ............1 Precaution for unpacking English G Stopper L............1 Hold the positions shown in the figure and remove the paper feeder from the outer case. H S Tite screw M4 × 20 ........4 Supplied parts A Paper feeder..........1 Be sure to remove any tape and/or cushioning B Pin ..............
  • Page 32 Procedure 1. Pull each cassette out and then remove the 3. Remove the lower paper cassette (3) from Be sure to turn the MFP main power switch off lift plate stopper (1) from each cassette and the MFP. and disconnect the MFP power plug from the attach it to the storage location (2).
  • Page 33 4. Place the MFP (6) on top of the paper feeder 5. Secure the MFP (6) to the paper feeder (A) 6. Refit the lower paper cassette (3) removed in (A) with the positioning pins (4) at the front using the two pins (B). step 3 to the MFP.
  • Page 34 7. Remove the screw (7) at the rear side of the 8. Remove the screw (9) to remove the metal 9. Secure the (C) with the screw (E). retainer paper feeder to remove the cover (8). plate (10). 7. Retirer la vis (7) située sur le côté arrière du 8.
  • Page 35 10. Insert the 12-P connector (11) of the paper 12. Refit the cover (8) using the screw (7) 13. Turn the adjusters on each corner (15) until feeder into the connector (12) on the MFP. removed in step 7. they reach the floor and then secure the paper feeder.
  • Page 36 Attaching the stays (For monochrome machines only) 14. Select holes (16) and install each stopper (F,G) with 2 S Tite screws M4 × 20 (H) so that the stoppers will be grounded on the floor. Fixation des supports (Pour machines monochromes) 14.

  • Page 37: Ändern Des Papierformats

    Changing paper size To change between inch size and metric 1. Holding the paper width adjusting tab,move 3. Move the size lever (18) up (C) or down (I). size,follow the steps below to adjust the size the paper width guide to a position other than C: metric size(centimeters) switch.
  • Page 38 Checking the center line 2. Load paper into the cassette and make a test 4. If the center of the paper (19) and that of the 1. Connect the MFP power plug to the wall copy to check the operation. test pattern output (20) do not meet the outlet and turn the MFP main power switch 3.
  • Page 39 Adjusting the center line 4. Output the test pattern again. 1. Open the cassette (21) of the paper feeder and loosen the three screws (23) securing the 5. Repeat steps 1 to 4 until the centers of the adjuster (22). paper and the test pattern meet the A and B: test pattern output examples reference value.
  • Page 40 INSTALLATION GUIDE FOR 3000 SHEETS PAPER FEEDER...

  • Page 41: Supplied Parts

    F Longitudinal size adjuster Be sure to remove any tape and/or cushioning English (inch specifications only) ......2 material from supplied parts. G Round cross-head tapping screw, M3 × 8 (inch specifications only) ......2 Supplied parts Stopper ............2 A Paper feeder..........1 I S Tite screws M4 ×...
  • Page 42 Procedure 2. Place the MFP (4) on top of the paper feeder 3. Secure the MFP (4) to the paper feeder (A) Be sure to turn the MFP main power switch off (A) with the positioning pins (2) at the front using the two pins (B).
  • Page 43 4. Refit the lower paper cassette (1) removed in 6. Remove the screw (7) to remove the metal plate (8). step 1 to the MFP. 7. Pull out the wire (9) covered with the black tube in front of the frame. 5.
  • Page 44 9. Separate the wire (9) covered with the black tube and the signal wires as shown on the above 11. Turn the adjusters on each corner (12) until drawing, and install the retainer (C) using the screw (7) removed in step 6 and the two M4 ×...
  • Page 45 Steps 12 to 14 below are only for 13. Install each stopper (H) with 1 S Tite screw 14. Refit the back cover (14) using the 3 screws monochrome machines. M4 × 8 (I). (13) removed in step 12. 12. Remove 3 screws (13), and then remove the back cover (14).
  • Page 46 Setting the paper size 1. Pull out the cassette of the paper feeder. 2. Move the sliders(15) at the machine front At the time of shipping, the paper size is set to Remove the lower paper cassette from the and rear inward (two at each point). Letter for inch specifications and A4 for metric MFP.
  • Page 47 Letter Letter Letter 4. Insert the upper tabs (19) and lower tabs (20) of the front and rear lateral size adjusters (16) into the upper slots (21) and lower slots (22) respectively such that the size indicators (18) point to the size of paper to be used. Secure the lateral size adjusters using the screw (17) for each. Check the paper size at the position with the front and rear upper tabs (19) inserted into the upper slots (21).
  • Page 48 24 (G) 24 (G) 24 (G) 23 (F) 23 (F) 6. Remove the screw (24) and remove the longitudinal size adjusters (23). (metric specifications only) 8. Return the paper feeder cassette and the 7. Depending on the paper size, align either the A4 pins (26) or the B5 pins (27) with the pin holes lower cassette in the MFP to their original (25) in the longitudinal size adjusters (23), fit the adjusters and secure each of them with a screw positions.
  • Page 49 Checking the center line 2. Select maintenance mode U402 and print 3. If the center of the paper (28) and that of the 1. Connect the MFP power plug to the wall the test pattern. test pattern output (29) do not meet the outlet and turn the MFP main power switch reference value, perform the following adjustment.
  • Page 50 Adjusting the center line 6. Output a test pattern again. 4. Pull out the cassette of the paper feeder and loosen the three screws (31) securing the adjuster 7. Repeat steps 4 to 6 until the centers of the (30). paper and the test pattern meet the reference value.
  • Page 51 Adjusting the front cover position Note: If the position of the adjuster is changed, adjust the front cover position. If the front cover position is not proper, the cassette may not be fixed with the magnet or the gap between the front cover and the paper feeder body may be opened.

  • Page 52: Document Finisher

    INSTALLATION GUIDE FOR DOCUMENT FINISHER Output Connector for Interconnecting Cable is non-LPS. Output: 587 VA max. Please use the item below Interconnecting Cable/ P/N: 305JA71610...
  • Page 53 F Binding screw M4 × 14........2 When installing the document finisher to a full- English color MFP, use parts (G), (H), (I), (J), (K) and (L) G Guide plate ...........1 supplied with the job separator. H Fixing plate F ..........1 Supplied parts I Fixing plate R ..........1 A Document finisher ........
  • Page 54 Procedure [Steps 1 to 5 below are only for full- 2. To align the document finisher with the paper Before installing the document finisher, first color machines.] outlet of the MFP, slide the legs of the attach the job separator. 1.
  • Page 55 3. Secure the guide plate (G) using the 4. Fit the fixing plate F (H) and the fixing plate 5. Fit the latch catch (B) to the fixing plate F (H) shoulder screw (L) and an S Tite screw M4 × R (I) to the left cover (3) using two S Tite and the fixing plate R (I) using two S Tite 10 (K).
  • Page 56 [Steps 1 to 6 below are only for 3. Fit the curl eliminator (M) to the eject cover 5. Close the eject cover (1). monochrome machines.] (1) such that the projections (4) on the cover 6. Fit the latch catch (B) to the eject cover (1) 1.
  • Page 57 7. Tip the rail retainer (C) over in the direction 8. Orient the guide rail (D) such that its pulley (6) is positioned toward the MFP. of the arrow so that the retainer fits into the groove in the guide rail (D). Ensure that the plate spring (4) fits into the groove and that the edge (5) of the guide rail (D) fits between the rollers behind the rail...
  • Page 58 8.0 mm 8.0 mm 9. Secure the rail retainer (C) to the MFP using two M4 × 10 binding screws (F) such that the front 10. Insert the guide rail (D) into the bottom of the and the rear gaps between the floor and the rail retainer (C) are approximately 8.0 mm. document finisher (A).
  • Page 59 10mm 10mm Fitting and adjusting the guide rail 12. Secure the guide rail (D) with the two M4 x 6 11. While pressing the guide rail (D) to the document finisher (A) so that the gap between the guide binding screws (E) so that there is a gap of rail (D) and the floor is approximately 10 mm, secure it using two M4 ×...
  • Page 60 13. Loosen temporarily the two screws (8) that secure the sheet metal (7) of the rail mounting plate 14. Slide the document finisher to engage it with (C) on the MFP , raise the sheet metal (7) by two divisions of the scale from the guide rail (D), the latch catch of the MFP.
  • Page 61 Adjusting the height of the document 2. Loosen the two screws (11) on the rear right caster of the document finisher (A). Adjust the finisher height of the rear right caster by turning its adjustment bolt (14) using a cross-headed 1.
  • Page 62 15 16 3. Adjust the height of the front right caster in the same manner as in step 4. Adjust the height of the left two casters in the same manner as in step 2 2 so that each center of the hooking portions (16) of the latch catch is so that the gaps (17a) and (17b) between the document finisher (A) aligned with the center of the two hooks (15) on the document finisher and the MFP are the same when the document finisher (A) is detached...
  • Page 63 6. After completing the installation, return to Connecting the signal cable Operation check pages 7 to 8 of the installation procedure and 1. Connect the signal cable (18) of the 1. Insert the MFP power plug to the wall outlet loosen the four M4 x 6 binding screws (E) in document finisher (A) to the MFP.
  • Page 64 INSTALLATION GUIDE FOR 3000 SHEETS DOCUMENT FINISHER Output Connector for Interconnecting Cable is non-LPS. Output: 587 VA max. Please use the item below Interconnecting Cable/ P/N: 303LT46210...
  • Page 65 AK-700 F Base slider A ........... 1 N Spring hook ..........1 English G Base slider B ........... 1 O Sponge ............ 1 Supplied parts H Plate............1 P M4 x 14TP coarse thread screw ....1 I M4 × 10 tap Tight S screw ...... 7 Q Plate foot R ..........
  • Page 66 AK-720 When installing the document finisher, (S), (T), V M4 × 10 tap Tight S screw ...... 9 AA Plate............1 (U) and eight (V) supplied with the job separator W Shoulder screw ........1 AB Assembly base ........1 are needed.
  • Page 67 Precautions Procedure Be sure to install the document finisher before installing the center-folding unit. Be sure to remove any tape and/or cushioning When installing the document finisher, install the Before installing the document finisher, make material from supplied parts. job separator in advance. sure that the MFP’s main power switch is turned Do not remove the two fixing tapes (a) from the off and that its power cord is unplugged from the...
  • Page 68 Removing the slider fixing pin 2. Open the right cover of the document 3. Remove the screw (2) to remove the slider finisher (A). fixing pin B (3). 1. Open the front cover of the document finisher (A). Remove the fixing tape from the slider of the inner tray and remove the slider fixing pin A (1).
  • Page 69 Removing the fittings 6. Pull the internal tray out. Installing the internal tray cover 7. Remove the fixing tape from the handle of 4. Open the front cover of the document 8. Install the internal tray cover (M) using the the internal tray and attach the spring hook finisher (A).
  • Page 70 Removing the fixing pin Installing the staple cartridge 14. When using a full-color machine, move to step 48 on page 14. 9. Turn the fixing pin (6) counterclockwise to 11. Remove the fixing tape from the staple remove it. cartridge holder (7). 10.
  • Page 71 [When installing the document finisher to the 17. Fit the curl eliminator (R) to the eject cover Installing the connecting plate monochrome machine] (8) such that the projections (11) on the 19. Install the connecting plate (D) to the left side cover fit into the two ends of the curl Installing the curl eliminator of the MFP or the printer using two M4 ×...
  • Page 72 Assembling the base slider Installing the base slider 20. Install plate foot R (Q) to base slider A (F) using M4 × 10 tap Tight S When using two paper feeders of 500 sheets Screw (I). 22.Open the right cover of the document finisher (A). 21.
  • Page 73 25. Place base slider B (G) onto base slider A (F). 27.Insert the base slider A (F), and then the base slider B (G) into the 26. Put plate (H) onto base slider B (G). lower left of the MFP or the printer. 28.Fix base slider B (G) with M4 x 14TP coarse thread screw (P).
  • Page 74 When using paper feeder of 3000 sheets 32.Insert the base slider A (F), and then the base slider B (G) into the lower left of the MFP or the printer. 31. Place base slider B (G) onto base slider A (F). 33.Fix base slider B (G) with M4 x 14TP coarse thread screw (P).
  • Page 75 34.Open the right cover of the document finisher (A). 35.Insert base slider A (F) under the document finisher (A) and hook the tabs (12). 36.Fix base slider A (F) with four M4 × 10 tap Tight S screws (I). 37.Close the right cover of the document finisher (A). 38.Move to step 39 on page 12.
  • Page 76 [Document finisher height adjustment method ] 42.Locate the adjustment pins (14). Adjusting the pin on the front and rear sides will change the height of 39. Adjust the height by turning the pin on the caster sections of the 2 slider the document finisher.
  • Page 77 43. In the case of the left illustration, turning the pin to the right allows the 45.Adjust so that the hole (16) on the side of the connecting plate (D) on caster's axle holder to be movable in the direction of the arrow, the MFP levels with the rib (15) on the document finisher (A) when the enabling the height of the document finisher to be lowered.
  • Page 78 [When installing the document finisher to the full-color machine] 50.Install the connecting plate (D) to fixing plates F (S) and R (T) using two M4 × 10 tap Tight S Screws (I). Installing the fixing and connecting plates Attach with the upper screw holes underneath fixing plates F (S) and R 48.
  • Page 79 Disassembling the base slider Installing the base slider 51. Remove the two screws (17) from the base slider A (F) to remove the When using two paper feeders of 500 sheets stay foot (18). 53.Insert base slider V (Z) and base slider A (F) under the assembly base 52.
  • Page 80 Y AA 55. Put base slider B (G) onto base slider A (F). In the same way, put base 57.Insert base slider A (F), base slider B (G) and plate (H) into the lower slider B (Y) onto base slider V (Z). left of the paper feeder.
  • Page 81 59. Secure base slider B (G) with a M4 x 14TP coarse thread screw (P) When the paper feeder of 3000 sheets is used and base slider B (Y) with a M4 x 14TP coarse thread screw (AD). 60.Put base slider B (G) onto base slider A (F). In the same way, put base Put the M4 x 14TP coarse thread screws (P, AD) through the upper slider B (Y) onto base slider V (Z).
  • Page 82 61. Insert base slider A (F) and base slider B (G) into the lower left of the 63.Secure base slider B (G) with a M4 x 14TP coarse thread screw (P) paper feeder. and base slider B (Y) with a M4 x 14TP coarse thread screw (AD). 62.
  • Page 83 64. Insert base slider V (Z) and base slider A (F) under the assembly base (AB) and hook the tabs (19). 65. Fix base slider A (F) with four M4 × 10 tap Tight S screws (I) and fix base slider V (Z) with four M4 ×...
  • Page 84 Removing the cover 68. Close the front cover of the document finisher (A). 66. Open the front cover of the document 69. Remove four screws (22) to remove the back finisher (A). cover (23) from the document finisher (A). 67. Remove two screws (20) to remove the lower front cover (21).
  • Page 85 Installing the assembly base (Be sure to perform this by two service personnel) 70. Align the projection (24) on the assembly base (AB) with the hole of the document finisher (A) and place the document finisher (A) on the assembly base (AB). Lift up the document finisher (A) by two service personnel simultaneously by one to hold (25) and the other to hold (26) and (27).
  • Page 86 Installing the cover [Adjusting the document finisher height] 76. Remove the two screws (32) to remove rear cover S (33). 72. Use four screws (22) removed from the 74. Remove the two screws (28) to remove front document finisher in step 69 to reinstall the cover S (29).
  • Page 87 77. Loosen the fixing screw (34) on the front right and rear right of the document finisher (A). 78. Adjust the height of the document finisher (A) by turning the bolt (37) using the spanner (31) so that the hole (36) on the side of the connecting plate (D) on the MFP levels with the rib (35) on the document finisher (A) when the connection is seen from the front.
  • Page 88 80. Adjust the height of the front left and rear left in the same way as steps 77 to 79 so that the gaps (38, 39) are equal to each other when the document finisher (A) and the MFP are connected together.
  • Page 89 Installing the sponge 84. Clean the sheet metal section under the upper cover (40) of the document finisher (A) with alcohol. 85. Peel the release paper off the sponge (O) and adhere the sponge as shown in the illustration. Installation de l’éponge 84.
  • Page 90 Installing the trays 87. . the right and left projections (41) of the tray 88. Lower tray B (C) and remove the two B (C) onto the document finisher (A) from its Lumiror films (42). 86. Use two nuts (K) and two pins (L) to install top.Fit the tray with the Lumiror films (42) the tray A (B) to the document finisher (A).
  • Page 91 [Installing the document finisher and the MFP] Connecting the signal line 89. Slide the document finisher (A) and connect it to the connecting plate (D) on the MFP. 90. Connect the signal line (44) of the document When making the connection, never hold the upper cover (43) of the document finisher (A). finisher (A) to the connector (45) at the back of the MFP.
  • Page 92 [Checking the curl] 92. Perform a test copy to check the paper is 93. Check the curl of the copy sample, and if the fed. curl is tight, follow the next step to adjust it. 91. Plug the MFP into a power outlet, and turn on its main power switch.
  • Page 93 Checking the curl 96.Close the front cover of the document finisher (A). 97.Check the paper is fed. If the ejected paper is tightly curled face-down (a) 98.Repeat steps 94 to 97 until the paper becomes straight. 94. Open the front cover of the document finisher (A). 95.
  • Page 94 If the ejected paper is tightly curled face-up (b) 101.Close the front cover of the document finisher (A). 102.Check the paper is fed. 99. Open the front cover of the document finisher (A). 103.Repeat steps 99 to 102 until the paper becomes straight. 100.Pull the pressure roller top adjusting knob E2 to your side and turn the knob by 1 scale in increasing order.

  • Page 95: Center-Folding Unit

    INSTALLATION GUIDE FOR CENTER-FOLDING UNIT...

  • Page 96: Supplied Parts

    F Douser ............. 1 Be sure to remove any tape and/or cushioning English G M3 × 8 tap-tight P screw ......2 material from supplied parts. Supplied parts H M4 × 8 tap-tight S screw ......11 A Center-Folding unit ........1 I Label ............
  • Page 97 Procedure Removing the cover. 3. Remove two screws (3) and remove lower left cover (4). Before installing the center-folding unit, turn 1. Open the front cover of the document fin- the MFP’s main power switch off and unplug isher. the power cable from the power supply. 2.
  • Page 98 Removing the back cover. Removing the reinforcing plate. Installing the back cover. 4. Remove the four screws (5) to remove the 5. Remove six screws (7) to remove the left 6. Use the four screws (5) which was removed back cover (6) from the document finisher. reinforcing plate (8).

  • Page 99: Anbringen Der Abdeckungen

    Removing the divided part. Reassembling the covers. 7. Cut out the divided part (9). 8. Install cover V (K) onto each of rear cover (C) and front cover (D) respectively with a M3 × 8 tap- tight P screw (G). Enlèvement de la pièce divisée.
  • Page 100 Installing the slider. 11. Align slider (E) with projection (12) on the back-side plate of the docu- ment finisher and install the slider. 9. Align slider (E) with projection (10) on the front-side plate of the docu- 12.Pull out slider (E) and secure it with two M4 × 8 tap-tight S screws (H). ment finisher and install the slider.
  • Page 101 Installing the cover handle saddle. Installing the center-folding unit. 13. Install cover handle saddle (J) on the front 14. Pull out sliders (E) till they stop. side of center-folding unit (A) with two M4 × 15. Align pawl (13) of center-folding unit (A) with projection (14) of slider (E) and place the center- 8 tap-tight S screws (H).

  • Page 102: Installing Covers

    Installing covers. 19. Store center-folding unit (A) into the docu- ment finisher. 17. Install the covers by fitting the projections on the rear side of the rear cover (C) and front cover (D) If center-folding unit (A) is not stored com- assembled in step 8 into the holes in the center-folding unit (A).
  • Page 103 Installing the folding tray. Installing the douser. Reinstalling the cover. 20. Fit the projection of folding tray (B) into the Before installing the douser (F), make sure 22. Reinstall the lower front cover (2) that was inside hole of center-folding unit (A). that center-folding unit (A) is securely stored.
  • Page 104 Adhering the label. [Checking staple position] 24. Clean the area where the label is adhered on 1. In the center-stapling mode, perform a test copy with the paper fed from the main tray. A test copy the right cover of the document finisher with must be made for each of the following paper sizes: alcohol and adhere label (I) aligning with A4R, LTR (8.5"...

  • Page 105: Adjusting Staple Position

    Adjusting staple position 2. Adjust setting value. When staples are placed too far right copy example (a): Decrease the setting 1. Enter the maintenance mode U246, select BOOKLET FOLDER and per- value. form adjustment for each copy sample size. When staples are placed too far left copy example (b): Increase the setting When A4R or LTR (8.5"...
  • Page 106 [Checking centerfold position] 3. If the distance from center line (1) on paper (c) to centerfold position (2) on the copy sample is out of the reference range, follow the steps 1. Plug the MFP into a power outlet, and turn on its main power switch. below to adjust the distance.
  • Page 107 Adjusting centerfold position When the centerfold position too far left copy example (e): Decrease the setting value. 1. Enter the maintenance mode U246, select BOOKLET FOLDER and per- Changing the value by 1 moves the centerfold position by approxi- form adjustment for each copy sample size. mately 0.55 mm.
  • Page 108 NOTICE English This accessory is for use only with the following Applicant's Listed Machine. Refer to the supplied guide to install the accessory in the field. Model ： DF-760 AVIS Français Cet accessoire est utilisable uniquement avec le copieur figurant dans la liste du demandeur suivant. Se reporter au guide fourni pour installer l'accessoire dans le champ.
  • Page 109 INSTALLATION GUIDE FOR MAILBOX...

  • Page 110: Supplied Parts

    F Tray name label ..........1 Be sure to remove any tape and/or cushioning English G Taptite S binding screw M4 × 10 ....4 material from supplied parts. H Plate foot V (for full-color machines).....2 I Plate foot F (for monochrome machines)..1 Supplied parts When installing the mailbox to a monochrome A Mailbox ............
  • Page 111 Procedure Before installing the finisher, carry out the [Carry out steps 1 when installing the Be sure to turn the MFP main power switch off following procedure. mailbox to a full-color machine.] and disconnect the MFP power plug from the 1.
  • Page 112 [Carry out steps 1 to 3 when installing 2. Hang the hook sections (5) of plate foot F (I) 3. Refit the lower front cover (2) to its original the mailbox to a monochrome on the finisher frame notches (6), and secure position, secure it using the screw (1), and machine.] them using 2 Taptite S binding screws M4 x...
  • Page 113 4. Remove the front top cover (6) and rear top 5. Fit the hooks (8) located at the front and rear Note: Lift the front and rear of the mailbox (A) cover (7) at the top of the finisher (5) using a of the bottom of the mailbox (A) into the lightly upward to make sure that the mailbox (A) flat-blade screwdriver or the like.
  • Page 114 6. Secure the front connection portion of the 7. Remove the rear cover (10) at the rear of the 8. Remove the fixing tape (12). mailbox (A) and the finisher (1) with the front mailbox (A) using a flat-blade screwdriver or 9.
  • Page 115 11. Fit the seven copy eject bins (D) to the ejection section of the mailbox (A) from the lowest bin to 12. Insert the MFP power plug to the outlet and the highest. turn the MFP main power switch on to check the operation.
  • Page 116 NOTICE English This accessory is for use only with the following Applicant's Listed Machine. Refer to the supplied guide to install the accessory in the field. Model ： DF-760/760(B) AVIS Français Cet accessoire est utilisable uniquement avec le copieur figurant dans la liste du demandeur suivant. Se reporter au guide fourni pour installer l'accessoire dans le champ.

  • Page 117: Hole Punch Unit

    INSTALLATION GUIDE FOR HOLE PUNCH UNIT...

  • Page 118: Parti Fornite

    F M4 × 8 tap Tight S screw ......1 English G M4 × 10 tap Tight S screw ....... 2 Supplied parts H Label ............1 A Hole punch unit........1 B Punch PCB ..........1 Be sure to remove any fixing tapes or cushion- C Power cord ..........
  • Page 119 Installation Procedure Removing the cover 2. Open the upper cover (3) and tray C (4) on the document finisher. Before installing the hole punch unit, make 1. Remove the four screws (1) to remove the 3. Remove four screws (5) and hold pressing sure the MFP’s main power switch is turned off back cover (2) from the document finisher.
  • Page 120 3 3 8 Removing the guide plate Installing the guide Installing the hole punch unit 4. Remove two screws (8) to remove the guide 5. Engage the projection and the pawl of the 6. Tilt the hole punch unit (A) to place it through the hole in the upper side of the document plate (9).
  • Page 121 Connecting the connector Installing the waste hole punch box Installing the punch PCB (120V/220V/230V/240V models only. 9. Open the front cover of the document finisher 12. Engage the pawl on the upper side of the and insert the waste hole punch box (D) along punch PCB (B) with the groove at the back of Except for Swedish specification) the guide (E) which was installed in step 5.
  • Page 122 14/15 19/20 21/22 23/24 13/16 17/18 25/26 14. Open the wire saddle (12) and put the 2P-connector (13) on the motor Figure (d): 6P-connector (19) of power cord (C) and YC3 connector through the wire saddle to fix the punch PCB (B). (20) of punch PCB (B) 15.
  • Page 123 Installing the cover 16. Engage the pawl (27) of the document finisher with the concave section (28) at the back of the top cover (7) which was removed in step 3. After that, reinstall the top cover (7) by pressing the finisher releasing lever (6) with four screws (5). If the pawl (27) is not securely engaged with the concave section, the top cover (7) is loose, which may cause incorrect operation of the document fin- isher.
  • Page 124 X’ -2mm X’ +2mm 18. Use four screws (1) to reinstall the back [Checking the center of the punch hole] cover (2) which was removed from the docu- 1. Plug the MFP into a power outlet, and turn on its main power switch. ment finisher in step 1.
  • Page 125 G G G G G G Centering punch-holes 3. Loosen two M4 × 10 tap Tight S screws (G) of the hole punch unit (A). 4. Adjust the position of the hole punch unit (A). 1. Open the upper cover (1) and the tray C (2) When holes are punched too far lower copy example (a): Slide the hole punch unit (A) to the of the document finisher.
  • Page 126 X’ -2mm X’ +2mm 7. Repeat steps 1 to 6 until the vertical gap of the punch holes on the copy sample are within the reference value. 8. After adjustment, tighten two M4 × 10 tap Tight S screws (G) loosened in step 3. 9.
  • Page 127 a: 9.5 2 mm a: 5.5 2 mm [Checking distance from leading edge to the punch holes] Adjusting distance from leading edge to the punch holes 1. In the punch mode, perform a test copy with paper fed from the MP 1.
  • Page 128 a: 9.5 2 mm a: 5.5 2 mm 3. Perform a test copy. 4. Repeat steps 1 to 3 until the distance from the leading edge to the punch hole indicates the value within the reference range. <Reference value> Distance (a) in metric specification: 9.5 ±2 mm Distance (a) in inch specification: 5.5 ±2 mm 3.

  • Page 129: Job Separator

    INSTALLATION GUIDE FOR JOB SEPARATOR...

  • Page 130: Piezas Suministradas

    F M4 × 10-tap-tight S screws ...... 6 I Stationary plate F ........1 J Stationary plate R ........1 G Wire saddle..........1 K M4 × 10 tap-tight screws......9 H Cover left OP ........... 1 Supplied Parts L Shoulder screw ........1 A Job separator...........
  • Page 131 Procedure Remove the left front cover. 2. Remove clip support (2). 3. Remove the two screws (3), release the Be sure to remove any tape and/or cushioning 1. Open the front cover (1). three latches (4) and remove the left front material from supplied parts.
  • Page 132 Remove the copy cover. Attach the retainer. 4. Unlock copy cover pawl (6) and then remove 6. Install the retainer (C) in the direction of the arrow and secure it with two M4 x 10 tap-tight S ejection cover (7). screws (F).
  • Page 133 Attach the copy tray. Attach the job separator. 8. Insert the copy tray (E) into the slot (14) in the MFP. 10. Open left cover (20). Push copy tray (E) until its hook (15) is engaged with the MFP projection (16). 11.
  • Page 134 12. Insert job separator (A) in the direction of the 13. Attach wire saddle (G) to the left side of the Attaching the upper left cover JS. arrow and secure it with two M4 × 10-tap- MFP. 16. Remove the screw (26) from the rear side of tight S (F) screws.
  • Page 135 17. Use the screw (26) that has been removed 18. Fit the engaging fitting (27) on the upper left cover JS (D) into the MFP and secure the cover by Procedure 16 to attach engaging fitting using the two M4 x 10 tap-tight S screws (F). (27) to the rear side of the supplied upper left cover JS (D).
  • Page 136 When installing the document finisher to the MFP, no need to per- Assemble the left front cover JS. form step 19. 20.Remove the screw (28) from the left cover that has been removed in 19. Attach cover left OP (H) to upper left cover JS (D) by engaging the pawl Procedure 3.
  • Page 137 22. Assemble by fitting the two pawls (31) on left front cover 1 (29) into the holes in the left front cover Attach the left front cover JS. JS (B). 25. Attach left front cover JS that has been 23. Fit the part (33) into the groove (32) of left front cover JS (B). assembled in Procedure 24 to the MFP and 24.
  • Page 138 26. Attach clip support (2) that has been [Operation check] removed in Procedure 2. 1. Insert the power plug of the MFP into an out- 27. Close the front cover (1). let and then turn the main power switch on. 2.

  • Page 139: Fax System

    INSTALLATION GUIDE FOR FAX System...
  • Page 140 English To install the FAX circuit board, see page 1. To install the FAX circuit board as Dual FAX, see page 11. Français Pour installer la carte à circuits FAX, se reporter à la page 1. Pour installer la carte à circuits FAX comme FAX double, se reporter à la page 11. Español Para instalar la tarjeta de circuitos de FAX, vea la página 1.
  • Page 141 Supplied parts E FAX operation section label ...... 1 (F) and (G) are not bundled. H Approval label When installing the Dual FAX, (A), (B), (C) are A FAX circuit board ........1 required. (Australian/New Zealand models only) ..2 B Modular connector cable Memory DIMM ..........
  • Page 142 <42,52 ppm> <42,52 ppm> Precautions Procedure 2. Install the memory DIMM (I) or the optional memory DIMM (J) into the memory slot (3) on Be sure to turn the MFP switch OFF and unplug Installing the memory DIMM the MFP from the power supply before installing <42,52 ppm (Monochrome machines)>...
  • Page 143 <30 ppm> <30 ppm> Installing the memory DIMM 2. Install the memory DIMM (I) or the optional <30 ppm (Monochrome machine)> memory DIMM (J) into the memory slot (3) 1. Remove 2 screws (1), and then remove the on the lower level (FLS). cover (2).
  • Page 144 <55/50 ppm> <25/25,30/30,40/40,50/40ppm> <25/25,30/30,40/40, 50/40,55/50 ppm> Installing the memory DIMM 2. Install the memory DIMM (I) or the optional memory DIMM (J) into the memory slot (3) on <25/25, 30/30, 40/40, 50/40, 55/50 ppm the middle level (FLS) <25/25, 30/30, 40/40, 50/40 ppm>. (Full-color machines)>...
  • Page 145 Remove the cover. Install the FAX circuit board. 4. Remove two screws (4) and then remove 5. Insert the FAX circuit board (A) along the groove in OPT1 and secure the board with two screws OPT1 cover (5). (4) that have been removed in step 4. Do not directly touch the FAX circuit board (A) terminal.
  • Page 146 Connect the MFP to the telephone line. For 100 V/120 V/Australian or Chinese models, 6. Plug the modular connector cable (7) into the use the supplied modular connector cable (B). line terminal, and then connect the other end to the telephone line. Connecter le MFP à...
  • Page 147 Connect the MFP to the separate phone If you don't connect the MFP to the separate (except for New Zealand model). phone, wipe the surface of the telephone 7. Plug the modular connector cable (8) into the terminal with alcohol and adhere the terminal telephone terminal, and then connect the seal (C) upon the customer's request.
  • Page 148 Seal the terminal (for New Zealand model). Attach the alphabet labels. 8. Wipe the surface of the telephone terminal 9. Wipe the area above the numeric keys at the right side of the operation panel with alcohol and with alcohol and adhere the terminal seal adhere the alphabet labels (D) here.
  • Page 149 Attach the FAX operation section label. 10.Wipe the label surface shown in the figure with alcohol and adhere the FAX operation section label (E) of the corresponding language. <When installing in 42,52 ppm (Monochrome machines)> Adhere the FAX operation section label (E) that A is shown. <When installing in 30 ppm (Monochrome machines)>...
  • Page 150 OPT2 42,52 ppm 30 ppm 25/25,30/30,40/40,50/40,55/50 ppm (305JP34010) (305JP34040) (305JP34070) OPT1 Attach the JATE label (for 100 V model only). 11. Perform this procedure for 100 V model only. Fixer l’étiquette JATE (modèle 100 V seulement). 11. Effectuer cette procédure pour le modèle 100 V seulement. Coloque la etiqueta JATE (sólo para el modelo de 100 V).
  • Page 151 <42,52 ppm> <30 ppm> For Australian model <25/25,30/30,40/40,50/40,55/50 ppm> OPT2 For New Zealand model Install the Dual FAX Attach the approval label (for Australian/New When installing the optional Dual FAX (when Zealand model only). adding the FAX circuit board to OPT2), proceed Refer to page 1 for the supplied parts.
  • Page 152 Remove the cover. Install the FAX circuit board. Do not directly touch the FAX circuit board (A) 1. Remove two screws (1) and then remove 2. Insert the FAX circuit board (A) along the terminal. Hold the top and bottom of the FAX OPT2 cover (2).
  • Page 153 Seal the terminal. Connect the MFP to the telephone line. 3. Wipe the surface of the telephone terminal 4. Plug the modular connector cable (4) into the with alcohol and adhere the terminal seal line terminal, and then connect the other end (C).
  • Page 154 Initialize the FAX circuit board. 3. If the FAX circuit board has been added to If [ALL] is selected in U698, both OPT1 and 1. Plug the MFP into a power outlet, and turn OPT2 (to initialize the FAX circuit board in OPT2 are initialized.
  • Page 155 INSTALLATION GUIDE FOR DT-710...
  • Page 156 Supplied parts 1. Reverse the document tray (A) and remove the 2. Remove the four screws (2) and remove the 3. Remove the two screws (6) and remove the 4. Remove the screw (8) and remove the upper English A Document tray ..........1 drawer (1).
  • Page 157 S tite screws M3 × 6 S tite screws M3 × 6 5. Temporarily tighten two 6. Fit the screw holes of the retainer (3) to the two 7. Use the two (C) that have 9. Use the four screws (2) that have been 10.Attach the upper right cover (9) so that the 11.
  • Page 158 INSTALLATION GUIDE FOR DUCT UNIT...
  • Page 159 E M3 x 20 tap-tight P screw 2. Attach DUCT A (A) using the following English (100-volt models only) ....... 2 screws: DUCT OPTION UNIT Installation Screws (1) removed in step 1: 2 Instructions M3 x 8 tap-tight P screw (C): 1 Supplied parts 1.
  • Page 160 3. Remove the filter cover (2). 4. Fit the two hooks (3) on DUCT B (B) into the 5. Attach DUCT B (B) using the two M3 x 8 tap- two holes (4). tight P screws (C). 3. Déposer le couvercle du filtre (2). 4.