Cleaning And Maintenance - Chicco KEY 2-3 ULTRAFIX Manual

entitled "FITTING THE CHILD CAR SEAT INSIDE THE
VEHICLE USING SAFETY BELTS".
REMOVING THE CHILD SEAT FROM THE CAR
1. Release the car safety belt.
2. Unthread the diagonal strap through the slot, ac-
companying it as it retracts.
If the Ultrafix clasps have been used to fasten the
car seat in place, they must now also be released:
1. Press the red button on the Ultrafix clasps and pull
the clasp out of the anchor point (Diag. 20).
2. Replace the clasps in the rear compartment and
pull the strap to make sure it is positioned correctly.
INSTALLING AND REMOVING THE CUP HOLDER
The child car seat has 2 inserts, one on the right and
one on the left of the side of the seat where you can
fit the cup holder whenever you like.
To install the cup holder:
1. Insert the cup holder into the relative slot (Diag. 21).
2. Press the cup holder downwards until it clicks into
place (Diag. 22).
WARNING! Do not place glass containers or hot
liquids on the cup holder as they could harm the
child.
To remove it:
1. Press the lever on the back of the cup holder and
lift it upwards, out of the slot (Diag. 23).
The cup holder slots are fitted with a special device
that makes sure it always remains in a horizontal
position.
To rotate and position the cup holder:
1. Press the lever on the back of the cup holder as
seen in Diag. 23 and rotate it to the desired position
(Diag. 24)
ADJUSTING THE HEIGHT OF THE BACKREST
It is possible to adjust the height of the backrest and
headrest to 8 different positions to guarantee that
the child's head is always well protected and the belt
is positioned properly on the shoulder.
To give you an idea, the child's ears must never be
higher than the headrest and the belt slot must al-
ways be higher than the child's shoulders (Diag. 25).
To adjust the backrest:
1. Use one hand to press the lever on the back of
the headrest whilst the other hand holds the seat
in place (Diag. 26).
2. Raise or lower the headrest/backrest to the de-
sired position (Diag. 27), then release the lever; you
will hear it click into place when it is locked in po-
sition.
ADJUSTING THE WIDTH OF THE BACKREST
The width of the backrest can be adjusted to adapt
the child car seat to the physique of the child.
To do so, use one hand to rotate the handle on the
back of the child car seat backrest and then:
1. turn it clockwise to widen the backrest (Diag.
28).
2. turn it counter clockwise to reduce the width of
the backrest (Diag. 29).
ADJUSTING THE INCLINATION OF THE BACK-
REST
The child car seat backrest can easily be moved and
adapted to fit the vehicle seat (Diag. 30).
The child car seat backrest can be reclined to 3 diffe-
rent positions to allow the child to travel in absolute
comfort.
Before adjusting the backrest, remove the child from
the child car seat.
To recline the backrest:
1. Insert a finger into the slot on the seat as seen
in Diag. 31.
2. Press the button in the slot whilst pulling/pushing
the rear adjuster handle to the desired position, as
illustrated in Fig. 32. Each click corresponds to one
position change
WARNING! On completing this operation, make sure
the adjuster handle is fixed firmly in place. When
you have completed the operations above, you can
install the child car seat in the vehicle and strap the
child inside as indicated in the relative chapter.
WARNING! Check that the car safety belt retractor
is behind the backrest of the car seat (or at least
aligned to it) (Diag. 5).
CLEANING AND MAINTENANCE
The covers on the headrest, backrest and seat are
all fastened with zips and Velcro so they are easy to
remove and replace whenever necessary.
HOW TO CLEAN THE FABRIC COVER
The child car seat's fabric cover can be removed and
cleaned by hand or in a washing machine at 30°C.
Please refer to the cleaning instructions on the fa-
bric label which illustrates the following washing
symbols:
Clean in a washing machine at 30°
Do not bleach
Do not dry clean
Do not tumble dry
Do not iron
Never use abrasive detergents or solvents. Do not
spin dry the fabric cover; let it dry without wringing
it.
To remove the various sections of the fabric cover
from the child car seat frame, follow the instructions
below:
Backrest
1. Open the 2 side zips on the headrest completely
22