Page 1
Member’s Mark 5-SHELF STORAGE RACK Item Number: 990332027 Model Number: 12-00005-MM Customer Assistance 1-888-549-1029 (spare/replacement parts): or Email: help@armadillotough.com 9 AM-5 PM EST, Monday-Friday, excluding US holidays 5x1.5_IM_banner_Q CONFIGURATION I CONFIGURATION II 48” X 24” X 72” (121.92 cm X 60.96 cm X 182.88 cm) 96”...
Page 2
Table of Contents Quality Statement........................3 Important Safety Information......................3 Before Assembly.........................3 Care & Use............................3 Configuration I / Components / Tools..................4 Configuration I: Step 1 – Step 11....................5 Configuration II / Components / Tools..................8 Configuration II: Step 1 – Step 4....................9 Warning..........................11 Danger..........................11 Limited Warranty Information....................11 Scan for easy 3D instructions...
Page 3
Quality Statement Question or Comments? We would love to hear about your Member’s Mark experience! Visit us at: Samsclub.com/membersmarkhelp Important Safety Information • Please read all instructions carefully before assembling this product. • Where applicable, and for your safety, assembly by two adults is recommended. •...
Page 4
Configuration I 48”W x 24”L x 72”H (121.92 cm x 60.96 cm x 182.88 cm) Maximum Capacity per Shelf: 800 lbs (362.9 kg). Maximum Capacity per Unit: 4000 lbs (1814.4 kg). Components A - Post B - Beam C - Brace D - Shelf E - Post Insert F - Post Cap...
Page 5
Configuration I STEP 1 STEP 2 Note: Posts are directional. The slot must point down. Shelf ledge up Tap lightly Skipping ONE slot from the bottom Post slot points down Tap lightly to seat rivets. Repeat for the opposite side. STEP 3 STEP 4 Shelf ledge up...
Page 6
Configuration I STEP 5 STEP 6 STEP 7 STEP 8 To create proper structure, the top and bottom rivets from the Beam To create proper structure, the top and bottom rivets from the Beam (part B) and Brace (part C) must be installed into the top and bottom (part B) and Brace (part C) must be installed into the top and bottom key holes of the posts (part A) on either side of the post insert (part E).
Page 7
Configuration I STEP 9 STEP 10 Shelf ledge up STEP 11 STEP 12 Need Assistance? Visit us at: samsclub.com/membersmarkhelp...
Page 8
Configuration II 96”W x 24”L x 36”H (243.84 cm x 60.96 cm x 91.44 cm) Maximum Capacity per Shelf: 800 lbs (362.9 kg). Maximum Capacity per Unit: 4000 lbs (1814.4 kg). Components A - Post B - Beam C - Brace D - Shelf E - Post Insert F - Post Cap...
Page 9
Configuration II STEP 1 STEP 2 Note: Posts are directional. The slot must point down. Shelf ledge up Tap lightly Skipping ONE slot from the bottom Post slot points down Tap lightly to seat rivets. Repeat for the opposite side. STEP 3 STEP 4 Shelf ledge up...
Page 10
Configuration II STEP 5 STEP 6 Shelf ledge up Install beams B & C at the bottom skipping 1st slot. It is not recommended to install higher than slot 6. Repeat for the opposite side. STEP 7 STEP 8 Need Assistance? Visit us at: samsclub.com/membersmarkhelp...
Page 11
Warning • The product is not recommended for outdoor use. • Do not alter the product in any way as it could compromise the performance of the unit as intended and will void all warranties. • Load small stable items on the top shelves, heavier and bulkier items should be stored on the lower shelves.
Need help?
Do you have a question about the 12-00005-MM and is the answer not in the manual?
Questions and answers