Advertisement
Quick Links
Advertisement
Related Manuals for Metallkraft GS 1000-12 P
Summary of Contents for Metallkraft GS 1000-12 P
- Page 1 Instruction Manual Thread Tapping Machine GS 1000-12 P GS 1000-12 P...
- Page 2 11.1 Ordering spare parts........13 11.2 Spare parts drawing........14 12 EC - Declaration of Conformity ......18 13 Notizen ..............19 Copyright information Copyright © 2021 Stürmer Maschinen GmbH, Hallstadt, Germany. Technical changes and errors excepted. GS 1000-12 P | Version 1.05...
- Page 3 Safety instructions are identified in these operating inst- Spare part order: ructions by symbols. The safety instructions are introdu- Fax: 0049 (0) 951 96555-119 ced by signal words that express the extent of the ha- E-Mail: ersatzteile@stuermer-maschinen.de zard. GS 1000-12 P | Version 1.05...
- Page 4 GS 1000-12 P | Version 1.05...
- Page 5 Certain work may only be carried out by specialist per- sonnel of the manufacturer. Other personnel are not aut- horized to perform this work. Contact our customer ser- vice department to carry out any work that may be required. GS 1000-12 P | Version 1.05...
- Page 6 - Do not touch rotating parts when the pneumatic - Maintenance work on an unsecured machine. tapping machine is working. - Non-observance of wear and damage marks. - Keep children away from the tapping machine. GS 1000-12 P | Version 1.05...
- Page 7 Threaded holes for 400 N / mm² M3 - M12 ning parts of polystyrene (PS). These materials must be [M(x)-M(y)] taken to a collection point for recyclable materials or to the responsible waste disposal company. Speed maximum [1/min] GS 1000-12 P | Version 1.05...
- Page 8 Then as- semble it as described in the following steps. Fig. 3: Description Thread Tapping Machine GS 1000-12 P Step 1: Carefully remove the components from the pac- kaging. Do not allow them to collide.
- Page 9 Step 6: Turn on the air supply. The machine is ready for The machine is equipped with a holder with torque limi- operation. ting function. Assembly instruction: Step 1: Fix the tap. Fig. 4: Mounting the tap Step 2: Connecting the quick-change chuck GS 1000-12 P | Version 1.05...
- Page 10 Do not set the limit torque too high, otherwise the tap 1,10 Nm will be damaged. 2,30 Nm 4,20 Nm 8,50 Nm 15 Nm 25 Nm When tapping in hard material, an adjustment is neces- sary. The following steps must be followed. GS 1000-12 P | Version 1.05...
- Page 11 The user can adjust the adjusting nut There is a risk of injury to the upper limbs when wor- of the tap to increase the torque limit. king improperly with the tapping machine. GS 1000-12 P | Version 1.05...
- Page 12 For maintenance work, please contact your nearest risk of serious injury. Metallkraft dealer. Please write down the following - All maintenance work must be carried out by quali- information from the machine or from the operating instructions beforehand, so that you can be helped fied personnel only.
- Page 13 Drawing number: 1 - In case of any uncertainties, always contact the ma- nufacturer. Item number: Tips and recommendations Use of non-approved spare parts will void the manu- facturer's warranty . GS 1000-12 P | Version 1.05...
- Page 14 11.2 Spare parts drawing Spare parts drawing 1 Upper frame Pneumatic motor Hinge Lower frame Tapping chuck Tapping shaft Air spring Air hose Oil-water se- parator Direction of rotation head Fig. 6: Spare parts drawing 1 GS 1000-12 P | Version 1.05...
- Page 15 Spare parts Spare parts table: Detail view Specification Desigantion Oil water separator Pneumatic motor Control panel Control Threaded shaft Collet/Chuck Reducer On Off Switch Air spring / piston GS 1000-12 P | Version 1.05...
- Page 16 Fig. 7: Spare parts drawing 2 Spare parts list 2 Pos. Description Size Bearing housing Bearing Planet carrier Washer Bearing Internal gear Inverted retaining rings Screw* M3x10 Ø 3 175x16.8 Needle bearing Planet gear Planet Carrier GS 1000-12 P | Version 1.05...
- Page 17 Ball bearing Rear end plate Throttle steam Throttle valve bushing O-Ring Spring Valve plug O-Ring Air regulator O-Ring Reverse bottom O-Ring O-Ring Taping Screw Ø3x18 Air inlet O-Ring Throttle lever Reverse valve bushing Housing Cover GS 1000-12 P | Version 1.05...
- Page 18 DIN EN ISO 11148-3:2013-05 Hand-held non-electric power tools - Safety requirements - Part 3: Drills and tappers Responsible for documentation: Kilian Stürmer, Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 11.11.2020 ______________________ Kilian Stürmer Managing Director GS 1000-12 P | Version 1.05...
- Page 19 Notizen 13 Notizen GS 1000-12 P | Version 1.05...
- Page 20 www.metallkraft.de...
Need help?
Do you have a question about the GS 1000-12 P and is the answer not in the manual?
Questions and answers