Metallkraft KRBS 101 Instruction Manual

Metallkraft KRBS 101 Instruction Manual

Combined pipe, section and belt grinding machine

Advertisement

Instruction Manual
Combined pipe,
section and belt grinding machine
KRBS 101
KRBS 101

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the KRBS 101 and is the answer not in the manual?

Questions and answers

Summary of Contents for Metallkraft KRBS 101

  • Page 1 Instruction Manual Combined pipe, section and belt grinding machine KRBS 101 KRBS 101...
  • Page 2: Table Of Contents

    Passing on as well as copying of this document, the use 13 Wiring Diagram........23 and distribution of its content are prohibited if not explic- 14 EC Declaration of Conformity....24 itly permitted. Contraventions are liable to compensa- 15 Notes............25 tion. Subject to technical modifications and error. KRBS 101 | Version 1.03...
  • Page 3: Introduction

    Fax: 0951 96555-119 avoided. E-Mail: ersatzteile@stuermer-maschinen.de We are always interested in valuable experience and knowledge gained from using the application, which then could be shared and be valuable to develop our products even further. KRBS 101 | Version 1.03...
  • Page 4: Obligations Of The Operating Company

    Machine. She must implement these in form of operating manuals for the operation the Machine. KRBS 101 | Version 1.03...
  • Page 5: Personal Protective Equipment

    The hearing protection protects the ears against damages of hearing due to noise. Breathing protection Fig. 1: Safety signs The breathing protection serves for protecting the respiratory passages and the lung against the intake of dust particles. KRBS 101 | Version 1.03...
  • Page 6: Intended Use

    Any use beyond the intended use or oth- erwise is considered misuse. Misuse: Fig. 2: Type Plate KRBS 101 The Pipe belt sander must neither be used for grinding flammable materials (e. g. magnesium, wood or similar).
  • Page 7: Packaging

    1 Cover for surface grinding station 2 Feed grinding 3 Cover belt grinding station 4 Cover grinding belt 5 Suction 6 Emergency stop button 7 Speed stage switch 8 Changeover switch pipe grinder L - belt sander R KRBS 101 | Version 1.03...
  • Page 8: Scope Of Supply

    - Roller for 1 1/2“ pipe - Roller for 50 mm pipe - Roller for 2“ pipe - Roller for 62 mm pipe - Roller for 2 1/2“ pipe - Roller for 28 mm pipe - Extraction unit (optional) KRBS 101 | Version 1.03...
  • Page 9: Mounting

    Step 3: Put both screws in and tighten them. Step 4: Connect the engine cable with the main connec- tion cable in the chassis. ATTENTION! The electrical connection of the engine cable has to be done by an electircan. KRBS 101 | Version 1.03...
  • Page 10: Electrical Connection

    The distance of the work surface to the sanding belt may be max. 2 tacle can be selected and mounted. KRBS 101 | Version 1.03...
  • Page 11 Step 4: To process the next workpiece, fold in the work- tighten the clamp screw again. piece stop and position the workpiece against the stop. KRBS 101 | Version 1.03...
  • Page 12: Surface Grinding Station

    The position of the contact roller (-20 mm - 0 mm - +20 mm) can be read on the scale. Step 4: Tighten the two clamping levers R. Fig. 16: Never reach into the openings on the Machine KRBS 101 | Version 1.03...
  • Page 13: Working Position Pipe Grinder

    Step 5: If necessary, adjust the desired grinding angle green Start Button. via the angle setting. To do this, loosen the Al- len screw and turn the workpiece clamping device to the desired degree. After adjust- ment, tighten the screw again. KRBS 101 | Version 1.03...
  • Page 14: Working Position Belt Sander

    Step 11: If machining of the workpiece on the belt sander tance of the work surface to the sanding belt may is complete, deburr the workpiece with the sur- be max. 2 mm. face grinding surface (2, Fig. 3) if necessary. KRBS 101 | Version 1.03...
  • Page 15: Working Position Surface Grinder

    Step 2: Switch off the extraction system. Machine. Step 3: Pull the mains plug of the grinding Machine. Damaged protection devices and machine parts must be properly repaired or replaced by an acknowledged specialist workshop. KRBS 101 | Version 1.03...
  • Page 16: Cleaning And Lubrication Of The Machine

    . WARNING! Step 4: Remove the sanding belt. When changing the sanding belt, the upper limbs between the drive roller and the sanding belt can be crushed. Step 5: Remove the contact roll. KRBS 101 | Version 1.03...
  • Page 17: Troubleshooting

    NOTE! Contact your neared Metallkraft dealer if you are una- ble to solve the problems with your machine. Please take the following information from the machine or from the operating manual so that we can help you in the best possible way.
  • Page 18: Disposal, Recycling Of Used Devices

    The contact roller for the Combined pipe, section and belt grinding machine KRBS 101 must be ordered. The These components must be disposed of separately and contact roller has the number 218 in the spare parts professionally.
  • Page 19: Spare Parts Drawings

    In case of service, the following drawings shall help to identify the necessary spare parts. If necessary, send a copy of the parts drawing with the marked components to your authorised dealer. Fig. 23: Spare Parts Drawing 1 KRBS 101 KRBS 101 | Version 1.03...
  • Page 20 Spare parts Fig. 24: Spare Parts Drawing 2 KRBS 101 KRBS 101 | Version 1.03...
  • Page 21 Spare parts Fig. 25: Spare Parts Drawing 3 KRBS 101 KRBS 101 | Version 1.03...
  • Page 22 Spare parts Fig.. 26: Spare Parts Drawing 4 KRBS 101 KRBS 101 | Version 1.03...
  • Page 23: Wiring Diagram

    Wiring Diagram 13 Wiring Diagram Fig. 27: Wiring Diagram KRBS 101 KRBS 101 | Version 1.03...
  • Page 24: Ec Declaration Of Conformity

    Risk assessment and reduction of risks (ISO 12100:2010) DIN EN 60204-1:2007-06 Safety of machinery - Electrical equipment of machines – Part 1: General requirements Responsible for documentation: Kilian Stürmer, Dr.-Robert-Pfleger-Str. 26, D-96103 Hallstadt Hallstadt, 27.06.2017 ______________________ Kilian Stürmer General Manager KRBS 101 | Version 1.03...
  • Page 25: Notes

    Notes 15 Notes KRBS 101 | Version 1.03...
  • Page 26 www.metallkraft.de...

Table of Contents