BIG ASS FANS HAIKU L Installation Manual
Hide thumbs
Also See for HAIKU L:
- Instructions manual (17 pages) ,
- Installation manual (84 pages) ,
- Installation manual
Subscribe to Our Youtube Channel
Related Manuals for BIG ASS FANS HAIKU L
Summary of Contents for BIG ASS FANS HAIKU L
- Page 1 HAIKU ® Installation Guide Guide d’installation Guía de instalación CONTACT FR127C-U1H FANSHOPPE.CA FR150C-U1H info@fanshoppe.ca FR127C-U1J FR150C-U1J 1-888-333-3239 FR112C-U1H AUTHORIZED DEALER...
- Page 2 CONTENTS Specifications ....................1 Before You Start .................... 2 Fan Installation ....................5 Troubleshooting ..................22 Maintenance ....................24 Contact Us ....................25 For assistance with troubleshooting issues that arise during fan installation, please contact Customer Service while the installer is present at the installation site.
- Page 3 SPECIFICATIONS Maximum Maximum Model Mounting Input Voltage Weight Watts FR127C-U1H 13.89 lb (6.3 kg) 39 W FR150C-U1H 14.33 lb (6.5 kg) 55 W Flat or sloped 100–240 VAC, FR127C-U1J ceilings 8 ft 13.45 lb (6.1 kg) 33 W 1 Φ, 50/60 Hz (2.4 m) or taller FR150C-U1J 13.89 lb (6.3 kg)
- Page 4 BEFORE YOU START ☑ Turn Off Power at Breaker Contact an electrician if you are uncomfortable performing electrical work. A licensed electrician must install the fan if required by local code. ☑ Gather Tools ☑ Prepare Fan Site and Gather Hardware CAUTION Do not use the fan with a dimmer switch or a third-party switch.
- Page 5 BEFORE YOU START ☑ Check Ceiling Slope Consult the table below to make sure you have the appropriate downrod length for your ceiling slope. The fan can be installed on a flat or sloped ceiling with an angle no greater than 33° (approximately 8:12 roof pitch). For minimum clearance guidelines, consult the Important Safety Instructions booklet included with this installation guide.
- Page 6 BEFORE YOU START ☑ Prepare Concrete Ceiling (if applicable) Use mounting bracket as drilling template and drill four Ø 8 mm holes in concrete ceiling (Fig. 1). The hole depth should not exceed 40 mm (Fig. 2). Remove dust from holes. Insert four M6 anchor bolts* into holes. Strike the heads of the anchor bolts with a hammer, ensuring bolt sleeves are flush with ceiling surface.
- Page 7 FAN INSTALLATION The fan stabilizer is required for outdoor installations and is for use on flat ceilings only. Electrical wires and safety cable not shown. Wiring Cover Mounting Bracket Wedge, Wedge Screw, Mounting Ball Fan Stabilizer* Steel Pin (2) M3 x 20 mm Screws* Downrod Control Box...
- Page 8 FAN INSTALLATION Hardware included Airfoil Hardware–Step 3 M5 x 12 mm Screw Motor Cover Hardware–Step 4 M3 x 6 mm Screw Lower Mounting Hardware–Step 5 M8 x 33 mm Bolt M8 Washer M8 Nut Upper Mounting Hardware–Step 7 Steel Pin Wedge Screw Wedge Safety Cable Shackle–Step 11...
- Page 9 FAN INSTALLATION 1. Install mounting bracket WARNING Disconnect power to fan location before installing mounting bracket. Mount only to an outlet box marked acceptable for fan support. Secure mounting bracket to mounting structure with suitable hardware (not supplied) (Fig. 1). Outlet box shown. Your mounting structure may differ. Mounting bracket electrical wires not shown.
- Page 10 FAN INSTALLATION 2. Wire fan WARNING Disconnect power to fan location before wiring fan. Do not connect fan to a damaged power source. Do not attempt to resolve electrical failures on your own. Consult a qualified electrician if uncertain of the electrical installation of this fan.
- Page 11 FAN INSTALLATION Fig. 2 AC NEUTRAL/L2 AC HOT/L1 PE/EARTH GROUND BROWN BLUE GREEN & YELLOW Wiring Harness...
- Page 12 FAN INSTALLATION 3. Install airfoils Make sure sticker color on each airfoil matches corresponding sticker color on fan hub. Tighten airfoil screws to 22.1 in·lb (2.5 N·m). Do not use power tools. Over-tightening screws may cause airfoils to warp and void your warranty.
- Page 13 FAN INSTALLATION 4. Install motor cover Secure motor cover to motor unit with M3 x 6 mm screws (Fig. 4). Fig. 4 M3 x 6 mm Screw Motor Cover...
- Page 14 FAN INSTALLATION 5. Install downrod Remove ground screw and tag from motor shaft (Fig. 5.1). Align arrow on downrod with arrow on shaft and connect downrod ground wire and safety cable to shaft (Fig. 5.2). Make sure cable lugs are pointing straight up and are not turned at an angle (Fig. 5.3). Route each wiring harness out of the downrod on the same side as its matching harness on the motor shaft (Fig.
- Page 15 FAN INSTALLATION Gently pull downrod wiring harnesses downward to create enough slack to reach motor shaft harnesses, and then connect the harnesses (Fig. 5.5). Make sure all hardware is secure, and then gently tug cables at top of downrod to reduce slack (Fig.
- Page 16 FAN INSTALLATION 6. Position motor cover trim and wiring cover Slide motor cover trim down the downrod until it stops. There will be a small gap between the trim and the motor cover. Slide the wiring cover down the downrod, resting it on the motor cover trim (Fig.
- Page 17 FAN INSTALLATION 7. Install mounting ball Do not over-tighten the wedge screw. Slide mounting ball over downrod (Fig. 7.1). Insert steel pin into hole at top of downrod, and then slide the mounting ball upward, seating the steel pin in the inner slots (Fig. 7.2). Insert wedge into mounting ball and secure with wedge screw (Fig.
- Page 18 FAN INSTALLATION 8. Install control box Slide control box into mounting bracket tray (Fig. 8). Fig. 8 Mounting Bracket Control Box 9. Hang fan Raise fan to mounting bracket. Align rib in mounting bracket with slot in mounting ball, position mounting ball, and let fan hang freely (Fig. 9). Gently twist downrod to ensure it is properly seated and will not move during fan operation.
- Page 19 FAN INSTALLATION 10. Connect wiring harnesses and Earth/Ground wire Connect the two wiring harnesses from the downrod to the harnesses on the back of the control box (Fig. 10.1). Remove ground screw and tag from mounting bracket and secure green Earth/Ground wire from downrod to mounting bracket (Fig. 10.1). Connect wiring harness from ceiling to wiring harness on front of control box (Fig.
- Page 20 FAN INSTALLATION 11. Secure safety cable Some local safety codes require the safety cable to be secured directly to an existing part of the building structure (Canada, Singapore). It may be necessary to install additional structural material to provide attachment points. Check your local safety code if you are unsure. Mounting Bracket Loop safety cable around mounting bracket and secure with shackle (Fig. 11a).
- Page 21 FAN INSTALLATION Building Structure Loop safety cable around building structure and secure with shackle (Fig. 11c). Acceptable building structures include a wooden beam or a metal mounting brace secured between two beams. In some cases, it may be necessary to install additional structural material to provide attachment points.
- Page 22 FAN INSTALLATION 13. Secure wiring cover Slide wiring cover up the downrod, aligning yellow arrow stickers so that top of wiring cover sits flush with mounting bracket. Make sure all wires and the safety cable are tucked into wiring cover, and then twist wiring cover clockwise to lock (Fig. 13.1). Fig.
- Page 23 Sleep comfortable while you sleep. Big Ass Fans Mobile App* Download the Big Ass Fans mobile app to group multiple fans, adjust their settings, and set your comfort preferences for hands-free control. For smart device integration instructions, visit www.bigassfans.com/support After connecting your fan to the app, use the app to make sure the fan’s firmware is up to date.
- Page 24 Insert light into bottom of fan and twist clockwise until you hear a click. 5. Turn on power to the fan and test fan/light operation using the remote. If the remote still will not control the fan/light, contact Big Ass Fans Customer Service.
- Page 25 TROUBLESHOOTING Issue Solution Use a long, thin object such as a small Allen wrench or pen tip to press the recessed tab on the wiring cover. While pressing the tab, turn the cover counterclockwise and slide down to remove. I need to remove the fan’s wiring cover.
- Page 26 MAINTENANCE WARNING Risk of fire, electric shock, or injury to persons during cleaning and user maintenance. Disconnect the appliance from the power supply before servicing. Please take a few moments each year to perform the following preventative maintenance procedures on your fan to ensure its safe and efficient operation. Check the safety cable, hardware, and wiring ☑...
- Page 27 CONTACT US FANSHOPPE.CA info@fanshoppe.ca 1-888-333-3239 AUTHORIZED DEALER OF BIG ASS FANS The information contained in this document is subject to change without notice. For the most up-to-date information, see the online printable installation guide at www.bigassfans.com/support/haiku-l Haiku is a trademark of Delta T LLC, registered in the U.S. and/or other countries.
Need help?
Do you have a question about the HAIKU L and is the answer not in the manual?
Questions and answers