VSG1432-B101 Series Overview The VSG1432-B101 is a VDSL2 router and Gigabit Ethernet gateway with a four-port built-in Ethernet switch and IEEE 802.11n wireless. The VSG1432-B101 allows wired and wireless clients to safely access the Internet. The built-in firewall blocks unauthorized access to your network. The USB port allows you to connect USB memory stick or USB hard drive for storing or sharing files through the network.
Page 4
• Always disconnect all cables from this device before servicing or disassembling. • Use ONLY an appropriate power adaptor or cord for your device. • Connect the power adaptor or cord to the right supply voltage (for example, 110V AC in North America or 230V AC in Europe). •...
VSG1432-B101 Series Hardware Setup Place the VSG1432-B101 flat on a desk or table or on the stand for a vertical installation. Remove the VSG1432-B101’s clear plastic covers before using it. To connect the stand, line up the arrow on the stand with the arrow on the bottom of the device as shown.
Page 6
To connect your VSG1432-B101: 1. Attach the antenna and point it up.
Page 7
VSG1432-B101 Series 2. Do one of the following for your Internet connection: a. DSL WAN: Use a telephone cable to connect your VSG1432- B101’s DSL port to a telephone jack (or the DSL or modem jack on a splitter if you have one). b.
Page 8
• The WLAN / WPS light flashes green and orange while WPS is in process. It stays on green when the wireless LAN is ready and blinks when there is traffic. • The INTERNET light turns on when the gateway is able to access the Internet and will blink when your VSG1432-B101 is sending or receiving data.
VSG1432-B101 Series Set Up a Wireless Network You can set up a wireless network using the following methods: Using Wireless Protected Setup (WPS) Press the WPS button on the VSG1432-B101’s front panel for more than 5 seconds to turn the WPS function on. Follow these steps to add a WPS-enabled device to the wireless network using the WPS/WLAN button.
Page 10
Set Up a Wireless Network Manually The wireless LAN on your VSG1432-B101 is enabled by default. To add a wireless client to the network, use the settings found on the bottom panel of your VSG1432-B101, which will look similar to the following example: SSID: ZyXEL00561 Security Mode: WPA-PSK...
Page 11
VSG1432-B101 Series 1. In your browser, if the VSG1432-B101 does not automatically re- direct you to the login screen, go to http://192.168.1.1. 2. Enter the default user name admin and password 1234. Click Login. If the login screen does not open, make sure you allow web browser pop-up windows, JavaScripts and Java permissions.
Page 12
4. In the next screen, you can change the login password. This is recommended. Enter your new password in the New Password field. Re-type your new password in the second field and then click Apply. If you prefer not to change the password, leave the two fields blank and click Skip.
Page 13
VSG1432-B101 Series 5. The Network Map page appears. This shows whether the VSG1432- B101 and computers/devices connected to it have Internet access. 6. Click Status to display the following screen, where you can view the VSG1432-B101’s device, interface, and system information.
Page 14
Viewing Certifications • Go to www.zyxel.com. • Select your product from the drop-down list box on the ZyXEL home page to go to that product's page. • Select the certification you wish to view from this page or click on...
VSG1432-B101 Series FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.