Page 1
THANK YOU We appreciate the trust and confidence you have placed in Everbilt through the purchase of this shallow well jet pump. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home...
Page 2
Table of Contents Safety Information ........2 Replacing An Old Pump .
Page 3
This warranty gives you specific legal rights and you may also have other rights which vary from state to state. Contact the Customer Service Team at 1-844-883-1872 or visit www.HomeDepot.com. HOMEDEPOT.COM Please contact Everbilt at 1-844-883-1872 for further assistance.
Page 4
Pre-Installation APPLICATION This unit is a single stage jet pump designed for shallow water well applications, where the water level is less than 25 ft. deep. If the water level to the pump is deeper than 25 ft. a convertible jet pump or a deep well submersible pump should be used. A pressure switch pre-set at 30 Psi "on", 50 Psi "off"...
Page 5
Wrap thread tape clockwise on all threaded connections. For all non-threaded connections, you must use PVC Purple Primer and PVC Cement to ensure airtight seals. Measure all pipe lengths before attaching. HOMEDEPOT.COM Please contact Everbilt at 1-844-883-1872 for further assistance.
Page 6
Installation WARNING: ELECTRICAL SAFETY Capacitor voltage may be hazardous. To discharge the motor capacitor, hold the insulated handle screwdriver BY THE HANDLE and short capacitor terminals together. Do not touch the metal screwdriver blade or capacitor terminals. If in doubt, consult a qualified electrician. WARNING: The pump body may explode if used as a booster pump unless a relief valve capable of passing full pump flow at 75 Psi is installed.
Page 7
Please go to Pages 10 and 11 for discharge pipe and tank connections. Pressure Switch Check Valve Suction Pipe From Well Priming Tee and Plug Check Valve Drive point below water level Drive Point HOMEDEPOT.COM Please contact Everbilt at 1-844-883-1872 for further assistance.
Page 8
Installation (continued) CASED WELL INSTALLATION, 2 IN. OR LARGER CASING □ Install the pressure gauge in the pump housing. □ Mount the pump as close to the well as possible. □ Assemble the foot valve, strainer, and well pipe. Make sure that the foot valve works freely. □...
Page 9
Please go to Pages 10 and 11 for discharge pipe and tank connections. Pressure Switch Check Valve Priming Tee and Plug 25 ft Max. Screen 10 ft Min. Foot Valve (Check Valve on foot of 5 ft Min. Suction Pipe) HOMEDEPOT.COM Please contact Everbilt at 1-844-883-1872 for further assistance.
Page 10
Discharge Pipe and Pressure Tank Connections PRE-CHARGE TANK CONNECTION □ Install two tees in the pump discharge port. The pipe size must be at least as large as the discharge port. NOTE: A pre-plumbed pump-on-tank system only requires one tee. □...
Page 11
Install reducing bushings down to 1/8 in. NPT for the barbed tting. Install the AVC tube between the barbed tting and the port on the bottom of the AVC (which is mounted on the tank). HOMEDEPOT.COM Please contact Everbilt at 1-844-883-1872 for further assistance.
Page 12
Pressure Switch Assembly Instructions WARNING: Before wiring the pressure switch, turn off WARNING: It is recommended all electrical work be the power source to which you are connecting to avoid performed by a licensed electrician. potentially life threatening electrical shock. WARNING: When wiring from the power source to the pressure switch, it is recommended that you use either a 14-gauge or 12-gauge cord.
Page 13
50 Psi. Run the pump through one or two complete cycles to verify correct operation. This will also help clean the system of dirt and scale dislodged during installation. Fill Pump and Piping through Priming Tee. Congratulations on a successful installation. HOMEDEPOT.COM Please contact Everbilt at 1-844-883-1872 for further assistance.
Page 14
Priming (continued) WINTERIZING THE PUMP To prepare the pump for freezing temperatures: □ Shut off power to the pump. □ Relieve system pressure. Open a faucet and let it drain until water stops flowing. □ Drain the pump. Your pump may have a separate drain plug. Remove this plug and let it drain. □...
Page 15
2 Psi less than the cut-in pressure. □ The pressure switch malfunctioning. □ Replace the pressure switch. □ There is a ruptured diaphragm/bladder □ Replace the tank. (pre-charged tank). HOMEDEPOT.COM Please contact Everbilt at 1-844-883-1872 for further assistance.
Page 16
Questions, problems, missing parts? Before returning to the store, call Everbilt Customer Service 8 a.m. - 6 p.m., EST, Monday - Friday 1-844-883-1872 HOMEDEPOT.COM Retain this manual for future use. Document #: EB-0089 05312024...
Page 17
GRACIAS Apreciamos la confianza que has depositado en Everbilt al comprar esta bomba de chorro para pozos poco profundos. Nos esforzamos en crear continuamente productos de calidad diseñados para mejorar tu hogar. Visítanos por Internet para ver nuestra línea completa de...
Page 18
Tabla de contenido Información de seguridad ......18 Instalaciones de bombas de chorro para pozos Garantía.
Page 19
Esta garantía te otorga derechos legales específicos y puede también tener otros derechos, que varían según el estado. Comunícate con el equipo de servicio al cliente al teléfono 1-844-883-1872 o visite www.HomeDepot.com. HOMEDEPOT.COM Para obtener asistencia, comunícate con Everbilt al 1-844-883-1872.
Page 20
Preinstalación SOLICITUD Esta unidad es una bomba de chorro de una sola etapa diseñada para aplicaciones en pozos de aguas poco profundas, donde el nivel del agua tiene menos de 25 pies (7.62 m) de profundidad. Si el nivel del agua de la bomba es más profundo que 25 pies (7.62 m), se debe usar una bomba de chorro convertible o una bomba sumergible de pozo profundo.
Page 21
área de flujo es demasiado pequeña, la altura de succión de la bomba y el caudal disminuirán significativamente. NOTA: El tamaño del tubo de succión no debe ser inferior a 1-1/4 plg. HOMEDEPOT.COM Para obtener asistencia, comunícate con Everbilt al 1-844-883-1872.
Page 22
Instalación ADVERTENCIA: SEGURIDAD ELECTRICA El voltaje del capacitor puede ser peligroso. Para descargar el condensador del motor, mantén el destornillador de mango aislado POR EL MANGO y las terminales del condensador corto unidos. No toques la hoja metálica del destornillador ni los terminales del condensador. En caso de duda, consulta a un electricista calificado.
Page 23
Interruptor de presión Válvula de retención Tubería de succión del pozo Conector en T y tapón de cebado Válvula de retención Punto de transmisión por debajo del nivel del agua Correa de transmisión HOMEDEPOT.COM Para obtener asistencia, comunícate con Everbilt al 1-844-883-1872.
Page 24
Instalación (continuación) INSTALACIÓN DE POZO ENVESTIDO, 2 PLG O CARCASA MÁS GRANDE □ Instala el manómetro en la carcasa de la bomba. □ Monta la bomba lo más cerca posible del pozo. □ Ensambla la válvula de pie, el colador y la tubería del pozo. Asegúrate de que la válvula de pie funcione libremente. □...
Page 25
Conector en T y tapón de cebado 25 pies máx. Malla Mínimo de 10 pies (3.05 m). Válvula de fondo (Válvula de retención al 5 pies (1,52 m) mín. pie del tubo de succión) HOMEDEPOT.COM Para obtener asistencia, comunícate con Everbilt al 1-844-883-1872.
Page 26
Conexiones de tubería de descarga y tanque de presión CONEXIÓN DEL TANQUE DE PRECARGA □ Instala dos T en el puerto de descarga de la bomba. El tamaño de la tubería debe ser al menos tan grande como el puerto de descarga. NOTA: Un sistema de bomba sobre tanque preinstalado solo requiere una T.
Page 27
Instale casquillos reductores hasta 1/8 pulg. NPT para el conector dentado. Instale el tubo AVC entre el conector de púas y el puerto en la parte inferior del AVC (que está montado en el tanque). HOMEDEPOT.COM Para obtener asistencia, comunícate con Everbilt al 1-844-883-1872.
Page 28
Instrucciones de montaje del interruptor de presión ADVERTENCIA: Antes de cablear el interruptor ADVERTENCIA: Se recomienda que todo el trabajo de presión, apaga la fuente de alimentación a la que eléctrico lo realice un electricista autorizado. se está conectando para evitar descargas eléctricas potencialmente mortales.
Page 29
Esto también ayudará a limpiar el sistema de suciedad y sarro desprendido durante la instalación. Llena la bomba y la tubería a través de la T de cebado. Felicitaciones por una instalación exitosa. HOMEDEPOT.COM Para obtener asistencia, comunícate con Everbilt al 1-844-883-1872.
Page 30
Cebado (continuación) PREPARANDO LA BOMBA PARA EL INVIERNO Para preparar la bomba para temperaturas bajo cero: □ Desconecta la energía a la bomba. □ Alivia la presión del sistema. Abre un grifo y déjalo escurrir hasta que deje de fluir agua. □...
Page 31
□ El interruptor de presión no funciona □ Reemplaza el interruptor de presión. correctamente. □ Hay un diafragma/vejiga roto (tanque □ Reemplaza el tanque. precargado). HOMEDEPOT.COM Para obtener asistencia, comunícate con Everbilt al 1-844-883-1872.
Page 32
¿Preguntas, problemas o piezas faltantes? Antes de regresar a la tienda, llama al Servicio al Cliente de Everbilt de lunes a viernes entre 8:00 a.m. y 6:00 p.m. (hora estándar del Este) 1-844-883-1872 HOMEDEPOT.COM Conserva este manual para referencias futuras.
Need help?
Do you have a question about the HDSWJ5P and is the answer not in the manual?
Questions and answers