About This User's Guide About This User's Guide Intended Audience This manual is intended for people who want to configure the ZyXEL Device using the web configurator. You should have at least a basic knowledge of TCP/IP networking concepts and topology.
Syntax Conventions • This product may be referred to as the “ZyXEL Device”, the “device” or the “system” in this User’s Guide. • Product labels, screen names, field labels and field choices are all in bold font.
Page 5
Document Conventions Icons Used in Figures Figures in this User’s Guide may use the following generic icons. The ZyXEL Device icon is not an exact representation of your device. ZyXEL Device Computer Notebook computer Server Printer Firewall Telephone Switch Router...
Safety Warnings Safety Warnings • Use only No. 26 AWG (American Wire Gauge) or larger telecommunication line cord. • Do NOT use this product near water, for example, in a wet basement or near a swimming pool. • Do NOT expose your device to dampness, dust or corrosive liquids. •...
Page 7
Safety Warnings This product is recyclable. Dispose of it properly. P-974H/HW Series User’s Guide...
Page 8
Safety Warnings P-974H/HW Series User’s Guide...
2.1 Overview ..........................23 2.2 Accessing the Web Configurator ..................23 2.2.1 Logging Out of the Web Configurator ................ 24 2.2.2 Resetting the ZyXEL Device ..................24 2.3 Navigating the Web Configurator ..................25 2.4 Changing the Login Password ..................... 26 Chapter 3 Status ............................
Page 10
Table of Contents Chapter 4 Basic ............................43 4.1 Overview ..........................43 4.1.1 What You Can Do in This Chapter ................43 4.1.2 What You Need to Know .................... 43 4.2 DHCP ..........................44 Chapter 5 Advanced..........................45 5.1 Overview ..........................45 5.1.1 What You Can Do in this Chapter ................
Page 11
Table of Contents Appendix B Sample Configurations..................77 7.5 Overview ..........................77 7.6 Connecting to the ZyXEL Device with Telnet ............... 77 7.6.1 Set Static IP Only ....................... 78 7.6.2 Set Static IP with Public DHCP .................. 78 7.6.3 Set Static IP with NAT ....................79 7.6.4 Set Static IP with NAT and Private DHCP ..............
Page 12
Table of Contents P-974H/HW Series User’s Guide...
List of Figures List of Figures Figure 1 Internet Access Application ..................... 19 Figure 2 Front Panel LEDs: P-974H ....................... 20 Figure 3 Front Panel LEDs: P-974HW ....................20 Figure 4 Status ............................25 Figure 5 Maintenance: Security ......................26 Figure 6 Status: SOFTWARE ........................
Page 14
List of Figures Figure 39 Red Hat 9.0: KDE: Network Configuration: Devices ............. 93 Figure 40 Red Hat 9.0: KDE: Ethernet Device: General ..............94 Figure 41 Red Hat 9.0: KDE: Network Configuration: DNS ..............94 Figure 42 Red Hat 9.0: KDE: Network Configuration: Activate ............
The ZyXEL Device is the ideal high-speed Internet access solution. It is compliant with the DOCSIS 2.0 and Cable Home 1.1 standards. The ZyXEL Device allows you to connect up to four computers to its 10/100 Mbps Ethernet ports and an additional computer to its USB 2.0 port to form your local area network and...
Table 1 Front Panel LEDs COLOR STATUS DESCRIPTION Green The ZyXEL Device is receiving power. The ZyXEL Device is not receiving power. Green The ZyXEL Device is functioning properly. The system is not ready or has malfunctioned. P-974H/HW Series User’s Guide...
Page 21
Green The ZyXEL Device has successfully registered to the cable operator’s network. Blinking The ZyXEL Device is trying to register with the cable operator’s network. The coaxial cable is not connected or the cable link is down. P-974H/HW Series User’s Guide...
Page 22
Chapter 1 Introduction P-974H/HW Series User’s Guide...
H A P T E R The Web Configurator 2.1 Overview The web configurator is an HTML-based management interface that allows easy setup and management via an Internet browser. Use Internet Explorer 6.0 and later or Firefox 1.5 and later versions. The recommended screen resolution is 1024 by 768 pixels.
If you forget your password or cannot access the web configurator, you will need to use the RESET button at the back of the ZyXEL Device to reload the factory- default configuration file. This means that you will lose all configurations that you had previously and the password will be reset to “1234”.
Chapter 2 The Web Configurator You can also use the RESET button to restart the ZyXEL Device (without restoring the defaults) by pressing down for 2 to 14 seconds. 2.3 Navigating the Web Configurator The following summarizes how to navigate the web configurator from the main Status screen.
It is highly recommended that you periodically change the password for accessing the ZyXEL Device. If you didn’t change the default one after you logged in or you want to change to a new password again, then click Maintenance > Security to display the screen as shown next.
Chapter 2 The Web Configurator The following table describes the related labels in this screen. Table 3 Maintenance: Security LABEL DESCRIPTION Password Enter the login user name whose password you want to change. The Change User ID default user name is “user”. New Password Type the new password in this field.
Page 28
Chapter 2 The Web Configurator P-974H/HW Series User’s Guide...
Acquire Downstream Channel In order to establish a successful connection with the cable provider’s network, the ZyXEL Device must first find and lock onto a frequency for communication with the cable operator’s network. The frequency is called a channel. Communication with the cable operator’s network cannot proceed until the ZyXEL Device finds the specific channel for sending and receiving data.
Page 30
If there is a problem making a TFTP connection with the cable operator’s CMTS, you will see the message Waiting for TFTP. If the ZyXEL Device does not receive a DHCP offer from the cable operator’s CMTS you will see the message Waiting for DHCP Offer.
These are called the Downstream Channel and Upstream Channel respectively. The channel numbers and frequencies are advertised by the cable operator’s CMTS during the initial booting of the ZyXEL Device; these may also be set in the configuration file.
Software Status System Up This is the elapsed time the system has been up. Time Network This field displays whether the ZyXEL Device is registered to the cable Access service provider’s network. Cable Modem This field displays the WAN IP address.
ZyXEL Device. Channel Lock Status The ZyXEL Device is either Locked or Not Locked on to the channel advertised by the cable operator’s CMTS. Modulation This is the method used to encode transmission information, similar to FM or AM on your radio.
Page 34
Chapter 3 Status Table 5 Status: CONNECTION (continued) LABEL DESCRIPTION Duration The IP address negotiated with your cable operator has a default lifetime of 7 days (e.g. D: 00 H: 01 M: 00 S: 00). The sequence (D -- H -- M -- S --) indicates that your modem configuration has failed or is in progress;...
The status message will display the This field displays: Downstream frequency in hertz (Hz) of the • Locked - The ZyXEL Device has locked Channel channel the ZyXEL Device has locked onto the downstream channel. onto or is trying to lock onto.
Page 36
Waiting for Time Server - The ZyXEL Device is waiting for a response from the time server. • Waiting for TFTP - The ZyXEL Device is waiting for a response from the TFTP server. • Operational - The ZyXEL Device has successfully gone through the boot up process.
The Event Log screen displays system logs. The logs are useful for debugging purposes when attempting to troubleshoot a connection problem between your ZyXEL Device and the cable operator’s CMTS. Click Status > EVENT LOG to display the screen as shown.
SEVERITY DESCRIPTION DHCP Warning - Critical The ZyXEL Device has received a response to its DHCP request from Non-critical field the cable operator’s CMTS, but the responding DHCP server did not invalid in include all of the required fields in the message. This message might...
Page 39
SW Upgrade Error Your ZyXEL Device has made 16 unsuccessful attempts to download Failed Before a new ZyXEL software image from the TFTP server (CMTS or other Download - TFTP server). After 16 attempts your cable modem aborts the Server not upgrade procedure.
Page 40
16 successive attempts, or until it reaches the maximum transmit power level. Started Unicast Critical Your ZyXEL Device is online and has sent a periodic Ranging Request Maintenance (RNG-REQ) message to the CMTS, without receiving a Ranging Ranging - No...
Page 41
5 minutes until it receives a valid response. ToD Response Warning Your ZyXEL Device received a reply from the ToD server that was received - specified by the DHCP server. The reply from the ToD server was Invalid data...
Page 42
Chapter 3 Status P-974H/HW Series User’s Guide...
The following terms and concepts may help as you read through this chapter. IP Address A static IP is a fixed IP that you configure on the ZyXEL Device. A dynamic IP is not fixed; a DHCP server provides an IP address to an Ethernet device each time it connects to the network.
LABEL DESCRIPTION DHCP DHCP Server Select Yes to set the ZyXEL Device as a DHCP server. Otherwise, select DHCP Server IP Enter the LAN IP address of the ZyXEL Device in the fields provided. DHCP Server Enter the subnet mask associated with the LAN IP address.
Internet. For example a home network and one in a business office. This requires special equipment on both ends of the connection. The ZyXEL Device is not one of the endpoints but it does allow traffic from those endpoints to pass through. The ZyXEL Device allows the following types of VPN traffic to pass through: P-974H/HW Series User’s Guide...
PassThrough using PPTP. Clear this option to disallow this type of VPN traffic. Multicast Enable Select this option to set the ZyXEL Device to forward multicast traffic. The ZyXEL Device acts as an Internet Group Management Protocol (IGMP) proxy and forwards multicast streams to multicast group members on your network.
Chapter 5 Advanced 5.3 IP Filtering You can set the ZyXEL Device to block access based on the IP address of a computer on the LAN. Computers whose IP addresses are specified in the IP Filtering screen are denied access to the ZyXEL Device and the Internet.
Chapter 5 Advanced 5.4 MAC Filtering You can set the ZyXEL Device to block access based on the Media Access Control (MAC) address of a computer on the LAN. Every Ethernet device has a unique MAC address. The MAC address is assigned at the factory and consists of six pairs of hexadecimal characters, for example “00:AC:12:00:01:15”.
Chapter 5 Advanced 5.5 Port Filtering You can set the ZyXEL Device to drop traffic based on service port numbers and protocol types. This feature allows you to specify the applications (such as MSN and TFTP) the computers on the LAN cannot use. See Appendix D on page 99 common services.
Chapter 5 Advanced 5.6 Port Forwarding You can set the ZyXEL Device to forward traffic to certain computers on your network based on the port numbers of incoming traffic. For example, if you set up an FTP server on your local network and you want it be available from the outside your LAN.
The wireless network is the part in the blue circle. In this wireless network, devices A and B use the access point (AP) to interact with the other devices (such as the printer) or with the Internet. Your ZyXEL Device is the AP. Every wireless network must follow these basic guidelines.
Normally, the ZyXEL Device acts like a beacon and regularly broadcasts the SSID in the area. You can hide the SSID instead, in which case the ZyXEL Device does not broadcast the SSID. In addition, you should change the default SSID to something that is difficult to guess.
Usually, you should set up the strongest encryption that every device in the wireless network supports. For example, suppose you have a wireless network with the ZyXEL Device. The ZyXEL Device does not have a local user database, and you do not have a RADIUS server. Therefore, there is no authentication.
The SSID (Service Set IDentification) is a unique name to identify the (SSID) ZyXEL Device in the wireless LAN. Wireless stations associating to the ZyXEL Device must have the same SSID. Enter a descriptive name of up to 32 printable characters (including spaces;...
Both the wireless stations and the access points must use the same WEP key. Your ZyXEL Device allows you to configure up to four 64-bit or 128-bit WEP keys but only one key can be enabled at any one time.
The key is not sent over the network. This key must be the same on the external authentication server and ZyXEL Device. You only need to configure RADIUS server settings if you enable 802.1x authentication.
Wireless clients authenticate with the RADIUS server before they can access your wireless network. Network Key The WEP keys are used to encrypt data. Both the ZyXEL Device and the 1.. 4 wireless stations must use the same WEP key for data transmission.
Chapter 6 Wireless LAN Therefore, if you don't have an external RADIUS server you should use WPA(2)- PSK (WPA -Pre-Shared Key) that only requires a single (identical) password entered into each access point, wireless gateway and wireless client. As long as the passwords match, a client will be granted access to a WLAN.
The key is not sent over the network. This key must be the same on the external authentication server and ZyXEL Device. Apply Click Apply to save your changes back to the ZyXEL Device. P-974H/HW Series User’s Guide...
Chapter 6 Wireless LAN 6.3.4 WPA-PSK/WPA2-PSK If you don’t have an external RADIUS server, you should use WPA(2)-PSK (WPA - Pre-Shared Key). WPA(2)-PSK only requires a single (identical) password entered into each WLAN member. As long as the passwords match, a client will be granted access to the wireless network.
Click Apply to save your changes back to the ZyXEL Device. 6.4 Access Control To change your ZyXEL Device Access Control settings click Wireless > Access Control. Note: Be careful not to list your computer’s MAC address and set the MAC Restrict Mode field to Deny when managing the ZyXEL Device via a wireless connection.
MAC addresses in the MAC Address table. Select Deny to block access to the router, MAC addresses not listed will be allowed to access the ZyXEL Device. Select Allow to permit access to the router, MAC addresses not listed will be denied access to the ZyXEL Device.
It is highly recommended that you periodically change the password for accessing the ZyXEL Device. If you didn’t change the default one after you logged in or you want to change to a new password again, then click Maintenance > Security to display the screen as shown next.
Restore to Select Yes to restore the ZyXEL Device settings to the factory Factory Defaults defaults. Otherwise, select No to keep your ZyXEL Device settings. Apply Click Apply to save your changes.
Ping Size Specify the size of the ping packet the ZyXEL Device is to send. The default is 64 bytes (56 bytes of data plus 8 bytes for the header). If you need to determine the Maximum Transmission Unit (MTU) size TCP/IP connection, change this setting.
Data Size Specify the number of data packet bytes the ZyXEL Device sends on the traceroute. The default is 40 bytes (32 bytes of data plus 8 bytes for the header). If you need to determine the Maximum Transmission Unit (MTU) size TCP/IP connection, change this setting.
This field is applicable when you select EURO in the Plan field. Offset Enter the offset. For example if you enter 50000, the ZyXEL Device will scan frequencies from the starting frequency to the last frequency in 50000 Hz increments.
Page 68
Chapter 7 Maintenance P-974H/HW Series User’s Guide...
Appendices and Index Product Specifications (71) Sample Configurations (77) Setting up Your Computer’s IP Address (81) Common Services (99) Legal Information (103) Customer Support (107) Index (113)
Internet. DHCP (Dynamic Host Use this feature to have the ZyXEL Device assign IP addresses, Configuration Protocol) an IP default gateway and DNS servers to computers on your network.
Appendix A Product Specifications Table 28 Device Specifications (continued) Maximum Data 30 Mbps Rate Symbol Rates 160, 320, 640, 1280, 2560 and 5120* Ksym/s Operating Level TDMA: +8 to +54 dBmV (32 QAM, 64QAM) +8 to +55 dBmV (8 QAM, 16QAM) +8 to +58 dBmV (QPSK) S-CDMA: +8 to +53 dBmV (all modulation types)
Page 75
Appendix A Product Specifications Table 29 P-974H/HW Power Adaptor Specifications (continued) Power Consumption 12W Max Safety Standards EN/IEC 60950-1:2001 AUSTRALIA PLUG STANDARDS AC Power Adapter Model MU18-2120150-A3 Input Power 100~240 Volts AC, 50-60 Hz, 0.6A Output Power 12 Volts DC, 1.5A 18W Power Consumption 12W Max Safety Standards...
Page 76
Appendix A Product Specifications P-974H/HW Series User’s Guide...
Open your Command Line prompt or terminal application. Telnet to 198.162.1.1. Login as admin (default password “1234”). After connecting to the ZyXEL Device, you can enter any of the commands in the following samples. Be sure to customize them first. P-974H/HW Series User’s Guide...
Appendix B Sample Configurations 7.6.1 Set Static IP Only To set only a static IP address, enter the following commands: > defaults > ip_sharing false > dhcp_enable false > dhcp_server 10.13.17.1 255.255.255.0 > static_ip 10.13.17.1 255.255.255.0 > dns_server 172.21.3.88 172.23.5.1 172.23.5.2 >...
Appendix B Sample Configurations 7.6.3 Set Static IP with NAT To set a static IP address with NAT, enter the following commands: > defaults > ip_sharing false > dhcp_enable false > dhcp_server 192.168.1.1 255.255.255.0 > static_ip 10.13.17.1 255.255.255.0 > dns_server 172.21.3.88 172.23.5.1 172.23.5.2 >...
> defaults > router_enable false > save > reset 7.6.6 Set Default IP Sharing / RG Mode To set the ZyXEL Device to its default IP Sharing / RG mode, enter the following commands: > defaults > save > reset Change the settings according to the information provided by your ISP or network administrator.
"communicate" with your network. If you manually assign IP information instead of using dynamic assignment, make sure that your computers have IP addresses that place them in the same subnet as the ZyXEL Device’s LAN port. P-974H/HW Series User’s Guide...
Appendix C Setting up Your Computer’s IP Address Windows 95/98/Me Click Start, Settings, Control Panel and double-click the Network icon to open the Network window. Figure 25 WIndows 95/98/Me: Network: Configuration Installing Components The Network window Configuration tab displays a list of installed components. You need a network adapter, the TCP/IP protocol and Client for Microsoft Networks.
Appendix C Setting up Your Computer’s IP Address Select Microsoft from the list of manufacturers. Select TCP/IP from the list of network protocols and then click OK. If you need Client for Microsoft Networks: Click Add. Select Client and then click Add. Select Microsoft from the list of manufacturers.
Click OK to save and close the TCP/IP Properties window. Click OK to close the Network window. Insert the Windows CD if prompted. Turn on your ZyXEL Device and restart your computer when prompted. Verifying Settings Click Start and then Run.
Appendix C Setting up Your Computer’s IP Address Windows 2000/NT/XP The following example figures use the default Windows XP GUI theme. Click start (Start in Windows 2000/NT), Settings, Control Panel. Figure 28 Windows XP: Start Menu In the Control Panel, double-click Network Connections (Network and Dial- up Connections in Windows 2000/NT).
Appendix C Setting up Your Computer’s IP Address Right-click Local Area Connection and then click Properties. Figure 30 Windows XP: Control Panel: Network Connections: Properties Select Internet Protocol (TCP/IP) (under the General tab in Win XP) and then click Properties. Figure 31 Windows XP: Local Area Connection Properties The Internet Protocol TCP/IP Properties window opens (the General tab in Windows XP).
Appendix C Setting up Your Computer’s IP Address • If you have a dynamic IP address click Obtain an IP address automatically. • If you have a static IP address click Use the following IP Address and fill in the IP address, Subnet mask, and Default gateway fields. •...
Appendix C Setting up Your Computer’s IP Address • Click OK when finished. Figure 33 Windows XP: Advanced TCP/IP Properties In the Internet Protocol TCP/IP Properties window (the General tab in Windows XP): • Click Obtain DNS server address automatically if you do not know your DNS server IP address(es).
Properties window. 10 Close the Network Connections window (Network and Dial-up Connections in Windows 2000/NT). 11 Turn on your ZyXEL Device and restart your computer (if prompted). Verifying Settings Click Start, All Programs, Accessories and then Command Prompt. In the Command Prompt window, type "ipconfig" and then press [ENTER]. You can also open Network Connections, right-click a network connection, click Status and then click the Support tab.
Appendix C Setting up Your Computer’s IP Address Macintosh OS 8/9 Click the Apple menu, Control Panel and double-click TCP/IP to open the TCP/ IP Control Panel. Figure 35 Macintosh OS 8/9: Apple Menu P-974H/HW Series User’s Guide...
• Type your IP address in the IP Address box. • Type your subnet mask in the Subnet mask box. • Type the IP address of your ZyXEL Device in the Router address box. Close the TCP/IP Control Panel. Click Save if prompted, to save changes to your configuration.
Appendix C Setting up Your Computer’s IP Address Macintosh OS X Click the Apple menu, and click System Preferences to open the System Preferences window. Figure 37 Macintosh OS X: Apple Menu Click Network in the icon bar. • Select Automatic from the Location list. •...
• Type your IP address in the IP Address box. • Type your subnet mask in the Subnet mask box. • Type the IP address of your ZyXEL Device in the Router address box. Click Apply Now and close the window.
Appendix C Setting up Your Computer’s IP Address Double-click on the profile of the network card you wish to configure. The Ethernet Device General screen displays as shown. Figure 40 Red Hat 9.0: KDE: Ethernet Device: General • If you have a dynamic IP address click Automatically obtain IP address settings with and select dhcp from the drop down list.
Appendix C Setting up Your Computer’s IP Address Click the Activate button to apply the changes. The following screen displays. Click Yes to save the changes in all screens. Figure 42 Red Hat 9.0: KDE: Network Configuration: Activate After the network card restart process is complete, make sure the Status is Active in the Network Configuration screen.
Appendix C Setting up Your Computer’s IP Address • If you have a static IP address, enter static in the BOOTPROTO= field. Type IPADDR= followed by the IP address (in dotted decimal notation) and type NETMASK= followed by the subnet mask. The following example shows an example where the static IP address is 192.168.1.10 and the subnet mask is 255.255.255.0.
Appendix C Setting up Your Computer’s IP Address Verifying Settings Enter ifconfig in a terminal screen to check your TCP/IP properties. Figure 47 Red Hat 9.0: Checking TCP/IP Properties [root@localhost]# ifconfig eth0 Link encap:Ethernet HWaddr 00:50:BA:72:5B:44 inet addr:172.23.19.129 Bcast:172.23.19.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1...
Page 98
Appendix C Setting up Your Computer’s IP Address P-974H/HW Series User’s Guide...
24032) Software. DNS(UDP/TCP:53) Domain Name Server, a service that matches web names (e.g. www.zyxel.com) to IP numbers. FINGER(TCP:79) Finger is a UNIX or Internet related command that can be used to find out if a user is logged on. FTP(TCP:20.21) File Transfer Program, a program to enable fast transfer of files, including large files that may not be possible by e-mail.
Page 100
Appendix D Common Services Table 30 Commonly Used Services SERVICE DESCRIPTION MSN Messenger(TCP:1863) Microsoft Networks’ messenger service uses this protocol. MULTICAST(IGMP:0) Internet Group Multicast Protocol is used when sending packets to a specific group of hosts. NEW-ICQ(TCP:5190) An Internet chat program. NEWS(TCP:144) A protocol for news groups.
Page 101
Appendix D Common Services Table 30 Commonly Used Services SERVICE DESCRIPTION TELNET(TCP:23) Telnet is the login and terminal emulation protocol common on the Internet and in UNIX environments. It operates over TCP/IP networks. Its primary function is to allow users to log into remote host systems.
Page 102
Appendix D Common Services P-974H/HW Series User’s Guide...
Published by ZyXEL Communications Corporation. All rights reserved. Disclaimer ZyXEL does not assume any liability arising out of the application or use of any products, or software described herein. Neither does it convey any license under its patent rights nor the patent rights of others. ZyXEL further reserves the right to make changes in any products described herein without notice.
Page 104
Appendix E Legal Information • This device must accept any interference received, including interference that may cause undesired operations. This device has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This warranty is in lieu of all other warranties, express or implied, including any implied warranty of merchantability or fitness for a particular use or purpose. ZyXEL shall in no event be held liable for indirect or consequential damages of any kind to the purchaser.
Page 106
(at the discretion of ZyXEL) and the customer will be billed for parts and labor. All repaired or replaced products will be shipped by ZyXEL to the corresponding return address, Postage Paid. This warranty gives you specific legal rights, and you may also have other rights that vary from country to country.
In the event of problems that cannot be solved by using this manual, you should contact your vendor. If you cannot contact your vendor, then contact a ZyXEL office for the region in which you bought the device. Regional offices are listed below (see also http:// www.zyxel.com/web/contact_us.php).
Page 108
• Regular Mail: ZyXEL Communications Oy, Malminkaari 10, 00700 Helsinki, Finland France • E-mail: info@zyxel.fr • Telephone: +33-4-72-52-97-97 • Fax: +33-4-72-52-19-20 • Web: www.zyxel.fr • Regular Mail: ZyXEL France, 1 rue des Vergers, Bat. 1 / C, 69760 Limonest, France P-974H/HW Series User’s Guide...
Page 109
• Sales E-mail: sales@zyxel.in • Telephone: +91-11-30888144 to +91-11-30888153 • Fax: +91-11-30888149, +91-11-26810715 • Web: http://www.zyxel.in • Regular Mail: India - ZyXEL Technology India Pvt Ltd., II-Floor, F2/9 Okhla Phase -1, New Delhi 110020, India Japan • Support E-mail: support@zyxel.co.jp •...
Page 110
• Sales E-mail: sales@zyxel.com.my • Telephone: +603-8076-9933 • Fax: +603-8076-9833 • Web: http://www.zyxel.com.my • Regular Mail: ZyXEL Malaysia Sdn Bhd., 1-02 & 1-03, Jalan Kenari 17F, Bandar Puchong Jaya, 47100 Puchong, Selangor Darul Ehsan, Malaysia North America • Support E-mail: support@zyxel.com •...
Page 111
• Support E-mail: support@zyxel.com.sg • Sales E-mail: sales@zyxel.com.sg • Telephone: +65-6899-6678 • Fax: +65-6899-8887 • Web: http://www.zyxel.com.sg • Regular Mail: ZyXEL Singapore Pte Ltd., No. 2 International Business Park, The Strategy #03-28, Singapore 609930 Spain • Support E-mail: support@zyxel.es • Sales E-mail: sales@zyxel.es •...
Index Index access control in WLAN default configuration Access Point (AP), see AP default IP address Advanced Encryption Standard (AES) default login information AES (Advanced Encryption Standard) device defaults AP (Access Point) device specifications authentication in WLAN DHCP 53, 57 DHCP (Dynamic Host Configuration Protocol) DHCP client DHCP server...
Page 114
Index IEEE 802.11b/g data rates password 24, 26, 63 changing IEEE 802.1x default Internet access 19, 71 physical specifications IP address ping test 65, 66 IP filtering Point-to-Point Tunneling Protocol (PPTP) IP pool setup pop-up windows IP Security (IPSec) port filtering IPSec (IP Security) port forwarding 50, 71...
Page 115
Index connection status event log WLAN status indicators, LEDs 53, 55 syntax conventions WEP (Wired Equivalent Privacy) system requirements Wi-Fi Protected Access (WPA) system status Wireless Local Area Network (WLAN) wireless model WLAN access control authentication 53, 57 basic setup Temporal Key Integrity Protocol (TKIP) encryption 53, 58...