Related Manuals for ZyXEL Communications P-974H - QUICK GUIDE V3.70
Summary of Contents for ZyXEL Communications P-974H - QUICK GUIDE V3.70
- Page 1 P-974H/HW Series Cable Router Firmware v3.70 Edition 2, 09/2009 DEFAULT LOGIN DETAILS IP Address: http://192.168.1.1:8080 Username: webadmin Password: 1234 Copyright 2009 ZyXEL Communications Corporation www.zyxel.com...
- Page 2 LEDs (P-974H and P-974HW) DATA POWER SYSTEM CABLE DATA POWER SYSTEM CABLE WLAN...
-
Page 3: How It Works
ENGLISH Introduction The P-974H/HW allows you to connect to the Internet through your cable TV service provider. The P-974H/HW is a DOCSIS2.0 and Cable Home 1.1 compliant Internet cable router with an integrated 4-port switch. The P-974HW also comes with IEEE 802.11g wireless capability. How It Works Overview •... -
Page 4: Hardware Connections
3. CABLE: Tighten one end of the coaxial cable to this port and the other end to a cable outlet. Overly tightened coaxial cable may affect transmission quality and/or break the connector pin. 4. POWER: Use only the included power adaptor to connect the ZyXEL Device to an appropriate power source. - Page 5 If you want to connect a Windows computer to the cable modem via USB, you also have to install the USB driver (see page 6). Do NOT connect the same computer to both the USB and LAN ports on the ZyXEL Device.
-
Page 6: Usb Driver Installation
The USB driver supports Windows 2000 and Windows XP. Follow the steps below to install the USB driver. 1. Save your work and close all applications. 2. Connect the ZyXEL Device to the USB port on your computer. A Found New Hardware Wizard screen displays. - Page 7 Verifying the Connection to the ZyXEL Device After you have finished the hardware connection and/or USB driver installation, check that you can connect to the ZyXEL Device via the USB connection. 1. Connect your computer to the USB port on the ZyXEL Device.
- Page 8 3. Type "ping” followed by a space and the IP address of the ZyXEL Device (192.168.1.1 is the default). 4. Press [ENTER]. The ZyXEL Device should send reply packets. This indicates that you have a successful connection. Connecting to the Web Configurator The ZyXEL Device’s built-in Web Configurator allows you to change the...
-
Page 9: Internet Access
ENGLISH 3. You should now see the Web Configurator’s Status screen. Internet Access Open your web browser and access any web site to test your Internet connection. -
Page 10: Troubleshooting
None of the LEDs turn on when you turn the power on. • Make sure that you use the included power adaptor to connect to the ZyXEL Device and that it is plugged into an appropriate power source. • Check all cable connections. If the LEDs still do not turn on, you may have a hardware problem. -
Page 11: Set Up Your Computer's Ip Address
This section shows you how to set your Windows NT/2000/XP computer to automatically get an IP address. This ensures that your computer can communicate with your ZyXEL Device. Refer to your User’s Guide for detailed IP address configuration for other Windows and Macintosh computer operating systems. -
Page 12: Product Certifications
9. Close the Network Connections screen. Product Certifications 1. Go to www.zyxel.com. 2. Select your product from the drop-down list box on the ZyXEL home page to go to that product's page. 3. Select the certification you wish to view from this page. -
Page 13: Sample Configurations
1. Open your Command Line prompt or terminal application. 2. Telnet to 198.162.1.1. 3. Login as admin (default password “1234”). After connecting to the ZyXEL Device, you can enter any of the commands in the following samples. Be sure to customize them first. -
Page 14: Set Static Ip Only
Set Static IP Only To set only a static IP address, enter the following commands: > defaults > ip_sharing false > dhcp_enable false > dhcp_server 10.13.17.1 255.255.255.0 > static_ip 10.13.17.1 255.255.255.0 > dns_server 172.21.3.88 172.23.5.1 172.23.5.2 > rip_enable true > rip2_md5 true >... -
Page 15: Set Static Ip With Public Dhcp
ENGLISH Set Static IP with Public DHCP To set a static IP address with a public DHCP server, enter the following commands: > defaults > ip_sharing false > dhcp_enable true > dhcp_server 10.13.17.1 255.255.255.0 > dhcp_pool 10.13.17.2 20 > static_ip 10.13.17.1 255.255.255.0 >... -
Page 16: Set Static Ip With Nat
Set Static IP with NAT To set a static IP address with NAT, enter the following commands: > defaults > ip_sharing false > dhcp_enable false > dhcp_server 192.168.1.1 255.255.255.0 > static_ip 10.13.17.1 255.255.255.0 > dns_server 172.21.3.88 172.23.5.1 172.23.5.2 > rip_enable true >... -
Page 17: Set Static Ip With Nat And Private Dhcp
ENGLISH Set Static IP with NAT and Private DHCP To set a static IP address with NAT and a private DHCP server, enter the following commands: > defaults > ip_sharing false > dhcp_enable true > dhcp_server 192.168.1.1 255.255.255.0 > dhcp_pool 192.168.1.2 20 >... -
Page 18: Set Bridge Mode
> defaults > router_enable false > save > reset Set Default IP Sharing / RG Mode To set the ZyXEL Device to its default IP Sharing / RG mode, enter the following commands: > defaults > save > reset Change the settings according to the information provided by your ISP or...