Advertisement
Quick Links
Instruction Manual
Model:
CSX6-M-EU
CSX6-M1-EU
CORDLESS CHAINSAW
• SAFETY
• ASSEMBLY
• OPERATION
CAUTION: Before using this tool, please read this manual completely,
• MAINTENANCE
and follow all operating safety measures.
Senix Australia Pty Ltd. 32/3 Westside Avenue, #Port Melbourne, Victoria, 3207
For customer support, please call 1300 461 825 or email us at info@senixtool.com
SENIX.COM.AU
English
Advertisement
Related Manuals for Senix X6 60V Brushless CSX6-M-EU
Summary of Contents for Senix X6 60V Brushless CSX6-M-EU
- Page 1 CAUTION: Before using this tool, please read this manual completely, • MAINTENANCE and follow all operating safety measures. Senix Australia Pty Ltd. 32/3 Westside Avenue, #Port Melbourne, Victoria, 3207 For customer support, please call 1300 461 825 or email us at info@senixtool.com SENIX.COM.AU...
- Page 2 Wear respiratory protection. of in an environmentally correct manner. Wear tight-fitted protective clothes. Use appropriate protection for foot-leg and hand-arm. Do not expose the product to rain or wet conditions. EN - 2 SENIX.COM.AU...
- Page 3 Damaged or entangled cords increase the correct power tool will do the job better and risk of electric shock. safer at the rate for which it was designed. e. If operating a battery charger in a damp 3 - EN SENIX.COM.AU...
- Page 4 Keep cutting tools sharp and clean. Prop- WARNING! erly maintained cutting tools with sharp cutting edges are less likely to bind and are Use only with SENIX X6 battery (B30X6/ easier to control. B40X6/B60X6/B80X6/B120X6) and g. Use the power tool, accessories and chargers (CHX6-L-EU/CHQX6-EU/CHQX6-M- tool bits etc.
- Page 5 Use of the chain saw for control of the chain saw in unexpected operations different than intended could situations. result in a hazardous situation. 5 - EN SENIX.COM.AU...
- Page 6 These conditions may significantly reduce the EN - 6 SENIX.COM.AU...
- Page 7 These symptoms normally appear in the fingers, hands or wrists. The risk increases at low temperatures. WARNING! This product produces an electromagnetic field during operation! This field may under some circumstances interfere with active 7 - EN SENIX.COM.AU...
- Page 8 Guide bar Battery-release button Saw chain Electric contacts Oil-tank cap Control panel Chain kickback brake handle Chain tensioning knob Front handle Side cover Lock-off button Side cover knob Trigger Oil storage plate Rear handle Guide bar cover EN - 8 SENIX.COM.AU...
- Page 9 Measurement Uncertainty K 105 dB(A) and K Recommended Operating -15°C-40°C Temperature Recommended Storage -20°C-70°C Temperature Weight (Tool Only) 4.1 kg *60V Max battery, maximum initial battery voltage (measured without a workload) is 60V. The nominal voltage is 56V. 9 - EN SENIX.COM.AU...
- Page 10 Ensure the battery pack is removed from the the side cover knob. chainsaw before attaching the bar and chain. Turn the side cover knob counterclockwise to remove the side cover and then loose the chain tensioning knob as much as possible. EN - 10 SENIX.COM.AU...
- Page 11 Charge the battery at an ambient temperature flat surface, so that the tank cap is facing of 4°C to 40°C (39.2°F to 104°F). upwards. Lift up the semicircular plate and rotate the oil tank cap counterclockwise to NOTE: remove it. 11 - EN SENIX.COM.AU...
- Page 12 Pull the chain kickback brack handle a correctly tensioned warm chain will hang towards the front handle to the operation approximately 1.3 mm out of the bar groove. position. 1.3 mm Fig. 9 Fig. 7 THE CONTROL PANEL EN - 12 SENIX.COM.AU...
- Page 13 If the tree in the figure. does make contact with any utility line, the company should be notified immediately. 13 - EN SENIX.COM.AU...
- Page 14 When the tree begins to fall remove the Fig. 16 product from the cut, switch off and put the product down then use the retreat path When the log is supported on both EN - 14 SENIX.COM.AU...
- Page 15 WARNING! property. Only perform cleaning and maintenance work according to these instructions! All further STORAGE works must be performed by a qualified • Clean chainsaw thoroughly as described specialist! above. 15 - EN SENIX.COM.AU...
- Page 16 Electrical products should not be discarded with household products. Used electrical products must be collected separately and disposed of at collection points provided for this purpose. Talk with your local authorities or dealer for advice on recycling. EN - 16 SENIX.COM.AU...
- Page 17 Refer to the manual to properly Chain installed backwards install the saw chain and guide Battery is discharged Charge the battery pack Product stops running suddenly Release the trigger and restart Overcurrent protection the machine 17 - EN SENIX.COM.AU...
Need help?
Do you have a question about the X6 60V Brushless CSX6-M-EU and is the answer not in the manual?
Questions and answers