Summary of Contents for Audio Physic REFERENCE CENTER 2
Page 1
Owner´s Manual Bedienungsanleitung REFERENCE CENTER 2...
Page 2
Included in the Delivery Your new loudspeaker is delivered in one box. This box contains the REFERENCE CENTER and an accessory pack, as well as your “Welcome to the Audio Physic Family“ package containing this Owner‘s Manual and the Final Inspection Certificate.
Page 3
Werk. Diese Maßnahmen tragen dazu bei, dass Sie zuhause in den vollen Genuss der hohen Material-, Fertigungs- und Klangqualität von AUDIO PHYSIC-Lautsprechern kommen. Im Regelfall wird Ihnen der kompetente AUDIO PHYSIC-Fachhändler den Lautsprecher liefern und installie- ren. Sollten Sie dies selbst tun wollen, helfen Ihnen die auf den folgenden Seiten beschriebenen Tipps und Schritte bei der sicheren Inbetriebnahme.
Page 4
Allgemeine Tipps Je nach Größe und Gewicht des Lautsprechers, bietet es sich an, diesen zu zweit auszupacken. Entnehmen Sie dem Karton zuerst das Zubehör. Folgen Sie für die sichere und korrekte Installation den Hinweisen im Kapitel „Auspacken und Aufstellen des Lautsprechers“. Der Lautsprecher sollte etwa Zimmertemperatur erreichen, bevor Sie ihn mit der HiFi-Anlage verbinden und in Betrieb nehmen.
Page 5
Auspacken und Aufstellen des Lautsprechers Stellen Sie den Karton auf den Fußboden. Öffnen Sie die Verpackung vorsichtig an den Klebestel- len der Längsseiten, am besten mit einem Taschen- oder Küchenmesser. Entnehmen Sie das Zubehör aus dem Karton. Ziehen Sie den Lautsprecher, gegebenenfalls zu zweit, aus dem Karton. Achten Sie unbedingt darauf, dass Sie beim An- oder Umgreifen der Box nicht die Chassis berühren, diese könnten irreparabel beschädigt werden.
Page 6
Anschließen des Lautsprechers Bitte schalten Sie alle Geräte Ihrer HiFi-Anlage aus, bevor Sie mit dem Anschließen des Lautsprechers beginnen. Befestigen Sie das Lautsprecherkabel an den Polklemmen der Box. Achten Sie dabei auf die korrekte Polarität. In aller Regel sind Lautsprecherkabel entsprechend gekennzeichnet, entweder mittels einer durchgehenden Markierung auf dem Kabel an einem der beiden Leiter oder über eine Kennzeichnung an den Kabelenden nach Plus „+“...
Page 7
AUDIO PHYSIC loudspeakers in the comfort of your own home. As a rule, your competent AUDIO PHYSIC dealer will deliver and install your loudspeaker. If you would rather install your product yourself, the following pages provide you with detailed tips and steps to follow in order to safely set up your loudspeakers.
Page 8
Anodised surfaces are sensitive to acids and alkalis and to ultraviolet light and may fade. The drivers in this range of AUDIO PHYSIC loudspeakers use a unique mounting technique. Rather than directly mounting the drivers onto the cabinet of the loudspeaker, the drill holes of the REFERENCE CENTER contain special neoprene plugs.
Page 9
Unpacking, Assembly and Set-up Place the box on the floor and and carefully open the packaging on the long side where it has been taped up, preferably using a pocket knife or kitchen knife. Remove the accessory pack from the box. Carefully remove the loudspeaker from the box.
Page 10
Connecting the Loudspeaker Please switch off all equipment in your HiFi system before you begin to connect your loudspeaker. Attach the loudspeaker cable to the connectors on the loudspeaker. When doing so, please make sure that you have the right polarity. As a rule, loudspeaker cables are accordingly labelled, either by a permanent marking on one of the two conductors of the cable or by plus “+”...
Page 11
4 Ohm Frequency range 40 Hz - 35 kHz Sensitivity 89 dB Loudspeaker systems Woofer 2x 7” DS Midrange 1x 5,9” HHCM SL Tweeter 1x 1,75”HHCT III AUDIO PHYSIC GmbH Almerfeldweg 38 59929 Brilon / Deutschland Germany Tel. +49(0)2961/9617-0 info@audiophysic.com www.audiophysic.com...
Need help?
Do you have a question about the REFERENCE CENTER 2 and is the answer not in the manual?
Questions and answers