Wallenstein WXT15V Operator's Manual

Hide thumbs Also See for WXT15V:

Setup instructions (24 pages)

page of 68

/ 68
Bookmarks

Quick Links

Download this manual

OPERATOR'S MANUAL

Serial number 1102975 and up

WXT 15V / WXT 20V / WXT 30V

Log Splitter

Revision: Nov-2024

Document number: Z97169_En

Need help?

Do you have a question about the WXT15V and is the answer not in the manual?

Questions and answers

Summary of Contents for Wallenstein WXT15V

Page 1 OPERATOR'S MANUAL Serial number 1102975 and up WXT 15V / WXT 20V / WXT 30V Log Splitter Revision: Nov-2024 Document number: Z97169_En...
Page 2 5. Controls .............22 11.1 Machine Specifications ........... 60 5.1 Splitter Control ............22 11.2 Hydraulic System Specifications ......60 5.2 WXT15V Engine Controls ........23 11.3 Bolt Torque ............. 61 5.3 WXT20V Engine Controls ........24 11.4 Hydraulic Fitting Torque .......... 62 5.4 WXT30V Engine Controls ........
Page 3 WARNING! current information, go to WallensteinEquipment.com. Do not start or operate the machine before Wallenstein Equipment Inc. • © 2024. All rights reserved. you read this manual. Make sure that you fully understand all the safety, operation, and No part of this work may be copied, reproduced, replaced,...
Page 4 Log Splitter 1.1 Delivery Inspection Report Wallenstein WXT15V / WXT20V / WXT30V Log Splitter To register your product and start the warranty, go to WallensteinEquipment.com. This form must be completed by the dealer at the time of delivery, and then signed by the dealer and customer.
Page 5 WXT15V / WXT20V / WXT30V Introduction Log Splitter 1.2 Serial Number Location Always provide the model and serial number of your Wallenstein product when you order parts, or request service or other information. The product information plate location is shown in the following illustration.
Page 6 This type of label gives the operator information or shows the operation of There are different types of labels on your Wallenstein product. a control. The labels are for safety, information, and product identification.
Page 7 • Accidents are preventable. You are responsible for the safe operation and maintenance of your Wallenstein Equipment product. You must make sure that you and anyone who uses, maintains, or works around the machine is familiar with the operation and maintenance procedures and related safety information in this manual.
Page 8 • Protective glasses, goggles, or a face shield. W016 • Long exposure to loud noise can Wallenstein Equipment puts considerable effort into designing cause permanent hearing loss. Power products that are safe to use; however, it is the responsibility of equipment, with or without a vehicle the operator to use the equipment safely.
Page 9 WXT15V / WXT20V / WXT30V Safety Log Splitter 2.5 Equipment Safety Guidelines 2.7 Safe Condition Safety is one of the primary concerns in equipment design and References are made to safe condition throughout this manual. development. However, every year there are accidents that can Safe condition means that you put the machine in a state that be prevented.
Page 10 WXT15V / WXT20V / WXT30V Safety Log Splitter 2.8 Training Record The design and manufacture of this product conforms to the applicable provisions in the following standards: Everyone who uses this machine must read and fully understand • ANSI/OPEI B71.7:2018 Powered Consumer Ram-Type Log all safety and operation information in this manual.
Page 11 WXT15V / WXT20V / WXT30V Safety Log Splitter 2.9 Work Site 2.9.2 Create a Safe Work Area Read and obey the instructions for safe operation of the CAUTION! machine. Keep bystanders and workers safe from hazards. Obey the The operator must be fully familiar with the work following important guidelines: site before starting work.
Page 12 WXT15V / WXT20V / WXT30V Safety Log Splitter 1. Safe zone 2. Work zone 10 ft (3 m) 10 ft (3 m) 10 ft (3 m) 10 ft (3 m) 02778 Figure 2 – Example of a safe work area...
Page 13 Replacement safety labels are available damaged, or illegible. If a component is replaced from your local Wallenstein Equipment dealer or distributor. and it has a safety label on it, apply a safety label to the new component. If a person operates •...
Page 14 Safety Labels Log Splitter 3.2 Safety Label Locations The WXT20V is shown; however, the WXT15V and WXT30V safety labels are in the same or almost the same locations. Numbers correspond with the Safety Label Definitions on page 16. 02774 Figure 3 – Safety label locations- left side (WXT20V shown)
Page 15 WXT15V / WXT20V / WXT30V Safety Labels Log Splitter 02775 Figure 4 – Safety label locations- right side (WXT20V shown)
Page 16 WXT15V / WXT20V / WXT30V Safety Labels Log Splitter 3.3 Safety Label Definitions 4. Warning! Put on the necessary PPE 1. Caution! For example: Read the Operator's Manual • A hard hat. There is important safety information and instructions in the Operator's •...
Page 17 WXT15V / WXT20V / WXT30V Safety Labels Log Splitter 7. Warning! Risk of cancer and reproductive harm The machine materials contain chemicals or machine operation can produce gases or dust that are identified by the state of California as causes of cancer, birth defects, or other reproductive harm.
Page 18 A Briggs & Stratton ® rear are determined when standing at the operator controls, (WXT15V) or a Vanguard ® (WXT20V and WXT30V) engine facing the direction of forward machine travel. provides power to the hydraulic system that moves the wedge.
Page 19 Log Splitter 4.4 Machine Components Know the machine components before you operate, service, or maintain the machine. 4.4.1 WXT15V Machine Components 02753 Figure 6 – WXT15V machine components 1. Engine 8. Split bed 15. Frame 2. Split-bed handle 9. Split-bed latch 16.
Page 20 WXT15V / WXT20V / WXT30V Familiarization Log Splitter 4.4.2 WXT20V Machine Components 02754 Figure 7 – WXT20V machine components 1. Engine 8. Split-bed latch 15. Ball-mount hitch (clevis hitch below) 2. Hydraulic fluid reservoir cap and dipstick 9. Tire (1 of 2) 16.
Page 21 WXT15V / WXT20V / WXT30V Familiarization Log Splitter 4.4.3 WXT30V Machine Components 02836 Figure 8 – WXT30V machine components 1. Engine 8. Split bed 15. Split-bed Handle 2. Support stand 9. Split-bed latch 16. Trailer jack 3. Hydraulic fluid reservoir cap and dipstick 10.
Page 22 WXT15V / WXT20V / WXT30V Controls Log Splitter 5. Controls WARNING! Do not operate the machine until you know the location of all the controls and how to use them correctly. WARNING! Before you start the engine, read and understand the safety and operating information under Engine Operation on page 31.
Page 23 Push the top of the switch to set the engine to standby. When the switch is in the Standby position, you can start the engine. 02631 Figure 11 – WXT15V engine choke control 02632 Figure 10 – WXT15V engine switch...
Page 24 The engine switch must be in the Standby position for the engine to start. STOP The engine is stopped. STOP STOP 02630 Figure 12 – WXT15V engine starter-cord handle Figure 13 – WXT20V engine throttle control and fuel shutoff 01733...
Page 25 WXT15V / WXT20V / WXT30V Controls Log Splitter 5.3.2 Choke Control 5.3.3 Starter-cord Handle The choke control lever has the following functions: WARNING! Closed Fast retraction of the starter cord (called Close the choke to start a cold engine. kickback) pulls your hand and arm toward the engine faster than you can let go of the handle.
Page 26 WXT15V / WXT20V / WXT30V Controls Log Splitter 5.4 WXT30V Engine Controls 5.4.2 Fuel Shutoff The fuel shutoff valve has the following functions: IMPORTANT! For complete information about the engine Closed controls, see the engine manufacturer's manual. Fuel valve is closed. The engine is off.
Page 27 WXT15V / WXT20V / WXT30V Controls Log Splitter 5.4.3 Choke Control 5.4.4 Starter-cord Handle The choke control lever has the following functions: WARNING! Closed Fast retraction of the starter cord (called Close the choke to start a cold engine. kickback) pulls your hand and arm toward the engine faster than you can let go of the handle.
Page 28 5.5 Split-bed Latch 5.6 Support Stand The split-bed latch holds the split bed in the horizontal position This section only applies to the WXT15V and WXT30V models. or the vertical position. The support stand stabilizes the machine while you split logs in The split-bed latch has two positions: the horizontal position.
Page 29 WXT15V / WXT20V / WXT30V Operating Instructions Log Splitter 6. Operating Instructions The operator must be familiar with and obey the operating • Read and understand this manual before you start the and safety procedures. machine. Review all safety information annually.
Page 30 WXT15V / WXT20V / WXT30V Operating Instructions Log Splitter 6.2 Pre-start Checklist 6.3 Machine Break-in Do the following before you start the machine the first time and Before and during the first eight hours of operation, do the each time after that.
Page 31 WXT15V / WXT20V / WXT30V Operating Instructions Log Splitter 6.3.4 After Eight Hours of Operation WARNING! 1. Complete the tasks that are listed under After One Hour of Operation. Fast retraction of the starter cord (called kickback) pulls your hand and arm toward the 2.
Page 32 If the engine floods, do one of the following: operation. Do not let the fuel tank become empty. • WXT15V: set the choke control to Open, and then try to 1. Park the machine on level ground. start the engine again.
Page 33 WXT15V / WXT20V / WXT30V Operating Instructions Log Splitter 6.4.4 Add Fuel to the Engine The engine needs clean, fresh, unleaded gasoline with a pump octane rating of 87 or higher (research octane number [RON] of 91 or higher). Gasoline with up to 10% ethanol (gasohol) is acceptable.
Page 34 (upper) mark. For instructions, Add Oil to the Engine on page 35. 7. Install the oil-level dipstick and make sure that it is tight. 02045 Figure 28 – WXT30V- check the engine oil level Figure 26 – WXT15V- check the engine oil level 02629...
Page 35 5. Remove the funnel, and then check the engine oil level. 6. Install the oil-fill cap and make sure that it is tight. 01779 Figure 30 – WXT20V- engine oil-fill locations 02628 Figure 29 – WXT15V- engine oil-fill location 02043 Figure 31 – WXT30V- engine oil-fill locations...
Page 36 WXT15V / WXT20V / WXT30V Operating Instructions Log Splitter 6.5 Hydraulic System Operation • Put on the correct eye protection when doing an inspection for a high-pressure hydraulic leak. A hydraulic system is a closed-loop system that provides pressurized hydraulic fluid to the splitter control.
Page 37 For instructions, see Lower the Jack Stand on page 47. 6.5.3 Add Hydraulic Fluid to the Reservoir 5. WXT15V or WXT30V: Lower the support stand and make sure that it is on the ground. For more information, see Lower the Support Stand on IMPORTANT! Do not fill the hydraulic-fluid reservoir higher page 38.
Page 38 When you remove the snap pin, the support stand can lower and cause injury. WARNING! This section only applies to the WXT15V or WXT30V models. Fast retraction of the starter cord (called Always lift the support stand before you move the split bed to kickback) pulls your hand and arm toward the the vertical position or before you transport the machine.
Page 39 For more information, see Splitter Control on page 22 and 3. Move the splitter control to the Neutral position. WXT15V Engine Controls on page 23. 4. Move the choke control to the Closed position. 1. Move the splitter control to the Retract position.
Page 40 If the support stand is not lowered, the machine can tip over and cause personal injury. For more information about the split-bed latch, see Split-bed Latch on page 28. 02799 Figure 34 – Split bed in the vertical position (WXT15V shown)
Page 41 • Cut logs to a correct length for the split bed. • Hold the sides of a log when you put it on the machine. Do not hold the cut ends of the log. 02798 Figure 35 – Split bed in the horizontal position (WXT15V shown)
Page 42 WXT15V / WXT20V / WXT30V Operating Instructions Log Splitter 6.12.2 Split a Log in the Horizontal Position IMPORTANT! Release the splitter control immediately when the wedge gets to the fully extended position. If you hold the splitter control after the wedge is fully extended, the hydraulic fluid will become too hot.
Page 43 WXT15V / WXT20V / WXT30V Operating Instructions Log Splitter 6.12.3 Split a Log in the Vertical Position 6.12.4 Remove a Blockage IMPORTANT! Release the splitter control immediately when WARNING! the wedge gets to the fully extended position. If you hold...
Page 44 1. Stop the machine. authority. For instructions, see Stop the Machine on page 39. WXT15V models are not intended for use or transport on 2. Put the split bed in the horizontal position. public roadways. Therefore, the machine does not include For instructions, see Move the Split Bed to the Horizontal the necessary lights, reflectors, and markings.
Page 45 WXT15V / WXT20V / WXT30V Transport Log Splitter 7.3 Ball-mount Hitch 7.3.3 Connect to a Ball-mount Hitch Make sure that there is space and clearance to safely reverse The machine comes with a ball-mount hitch coupler. the tow vehicle to the machine.
Page 46 8. Install the hitch pin through clevis hitch, and then install the snap-lock pin through the hitch pin. 02763 Figure 42 – Clevis hitch (WXT15V shown) 7.4.1 Connect to a Clevis Hitch Make sure that there is space and clearance to safely reverse the tow vehicle to the machine.
Page 47 WXT15V / WXT20V / WXT30V Transport Log Splitter 7.5 Jack Stand 7.5.2 Lift the Jack Stand 1. Support the machine to remove weight from the jack stand. Attach the machine to a tow vehicle or support the front of CAUTION! the machine with blocks.
Page 48 WXT15V / WXT20V / WXT30V Transport Log Splitter 7.6 Trailer Jack 7.6.2 Stow the Trailer Jack 1. Support the machine to remove weight from the trailer jack. WARNING! Attach the machine to a tow vehicle or support the trailer tongue with blocks.
Page 49 • Store the machine indoors, where possible. • If necessary, support the frame with planks. 8.2 Put the Machine in Storage WXT15V or WXT30V: Keep the support stand in the lifted position for storage. For information about engine storage, see the engine manufacturer's manual.
Page 50 WXT15V / WXT20V / WXT30V Storage Log Splitter 8.2.1 Replace the Engine Fuel 1. Remove the current fuel from the engine. Operate the machine until the fuel tank is empty or drain the fuel tank and properly dispose of the fuel.
Page 51 WXT15V / WXT20V / WXT30V Service and Maintenance Log Splitter 9. Service and Maintenance Regular preventive maintenance can improve performance and SAFE CONDITION prolong the life of the machine. Machine maintenance is your responsibility. 1. If the machine is attached to a tow vehicle, set the tow-vehicle parking brake, stop the engine, and remove the ignition key.
Page 52 WXT15V / WXT20V / WXT30V Service and Maintenance Log Splitter 9.2 Fluids and Lubricants 9.2.3 Engine Fuel For complete fuel information and use at high altitudes, see The machine needs the correct fluids and lubricants for the engine manufacturer's manual.
Page 53 Clean the machine. See page 58. WXT15V model engines have Briggs & Stratton Just Check & Add™ Technology, which means that it is not necessary to Change the hydraulic fluid and filter. See page 57. change the oil.
Page 54 Clean the grease fitting thoroughly or get a new grease fitting. d. Install the grease fitting. Number of Item Location Frequency Locations Wheel bearings 100 hours or annually 02761 Figure 48 – Grease fitting, hinge, and pivot point locations (WXT15V shown)
Page 55 • Do not hit the flywheel with a hard object or metal tool. This can cause the flywheel to shatter during operation. Use the correct tools to service the engine. • Do not touch a hot muffler, cylinder, or fins. Contact can cause burns. 02627 Figure 49 – WXT15V- engine air filter...
Page 56 WXT15V / WXT20V / WXT30V Service and Maintenance Log Splitter 9.6.1 Hydraulic System Maintenance Safety WARNING! Pressurized hydraulic fluid can penetrate the skin or eyes and cause serious illness, injury, or death. • Make sure that all hydraulic connections are tight before you apply pressure to the hydraulic system.
Page 57 WXT15V / WXT20V / WXT30V Service and Maintenance Log Splitter • Immediately replace a hydraulic hose or tube that shows The hydraulic fluid filter is on the rear of the machine, on the left signs of swelling, wear, leaks, or damage. A swollen, worn, side.
Page 58 WXT15V / WXT20V / WXT30V Service and Maintenance Log Splitter 9.7 Clean the Machine 9.8 Tire Maintenance IMPORTANT! Do not use gasoline, diesel fuel, or thinners WARNING! for cleaning. Harsh chemicals can damage the machine finish. Failure to follow the correct procedures when...
Page 59 Set the machine to a safe condition. or Wallenstein Equipment. When you contact someone, please have the serial number of your product available. To find the For engine troubleshooting, see the engine manufacturer's serial number on your machine, see Serial Number Location on manual.
Page 60 WXT15V / WXT20V / WXT30V Specifications Log Splitter 11. Specifications For engine specifications, see the engine manufacturer's documentation. For available accessories, go to WallensteinEquipment.com. 11.1 Machine Specifications Parameter WXT15V WXT20V WXT30V Compatibility Towable or self-contained Engine Briggs & Stratton® 5.5 hp (190 cc) Vanguard®...
Page 61 WXT15V / WXT20V / WXT30V Specifications Log Splitter 11.3 Bolt Torque Imperial Bolt Torque Specifications Torque IMPORTANT! If you replace hardware, use fasteners Bolt of the same grade. SAE Gr. 2 SAE Gr. 5 SAE Gr. 8 Diameter lbf•ft N•m lbf•ft...
Page 62 WXT15V / WXT20V / WXT30V Specifications Log Splitter 11.4 Hydraulic Fitting Torque Hydraulic Fitting Torque Specifications Tighten flare-type tube fittings: Hex size Tube size across Flats from finger 1. Check the flare and flare seat for defects that might flats...
Page 63 Warranty Log Splitter 12. Warranty LIMITED WARRANTY Wallenstein products are warranted to be free of defects in materials and workmanship under normal use and service, for a period of Five Years for Consumer Use Two Years for Commercial/Rental Use from the date of purchase, when operated and maintained in accordance with the opera�ng and maintenance instruc�ons supplied with the unit.
Page 64 WXT15V / WXT20V / WXT30V Index Log Splitter 13. Index Operation 31 Operation safety 31 Air filter, clean 55 Specifications 60 Switch 23 Equipment guidelines, safety 9 Ball-mount hitch 45 Connect to 45 Coupler...
Page 65 WXT15V / WXT20V / WXT30V Index Log Splitter Inspection Remove a blockage 43 Dealer checklist 4 Report, delivery inspection 4 Delivery report 4 Rewind start 27 Introduction 3 Rust protection oil Hinge and pivot point locations 54...
Page 66 WXT15V / WXT20V / WXT30V Index Log Splitter Storage 49 Put the machine in storage 49 Remove the machine from storage 50 Replace engine fuel 50 Storage safety 49 Support stand 28 Change position 38 Switch, engine 23...
Page 67 WXT15V / WXT20V / WXT30V Index Log Splitter...
Page 68 WallensteinEquipment.com...

This manual is also suitable for:

Wxt20v Wxt30v