Download Print this page

CP Plus ORANGE CP-UNC-VB21L3C-MDS Quick Start Manual

Advertisement

Quick Links

Network Camera
Quick Start Guide
Version: 1.0
Introduction 1

Advertisement

loading
Need help?

Need help?

Do you have a question about the ORANGE CP-UNC-VB21L3C-MDS and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for CP Plus ORANGE CP-UNC-VB21L3C-MDS

  • Page 1 Network Camera Quick Start Guide Version: 1.0 Introduction 1...
  • Page 2 Foreword General Safety This manual introduces the functions, installation and operations of the camera. Instructions The following categorized signal words with defined meaning might appear in the manual. Signal Words Meaning Indicates a medium or low potential hazard which, if not avoided, could result in slight or moderate injury.
  • Page 3 All the designs and software are subject to change without prior written notice. The product updates might cause some differences between the actual product and the manual. Please contact the customer service for the latest program and supplementary documentation. There still might be deviation in technical data, functions and operations description, or errors in print.
  • Page 4 Important Safeguards and Warnings Electrical safety All installation and operation should conform to your local electrical safety codes. The power source shall conform to the Safety Extra Low Voltage (SELV) standard, and supply power with rated voltage which conforms to Limited power Source requirement according to IEC60950-1.
  • Page 5 Device body can be cleaned with soft dry cloth, which can also be used to remove stubborn stains when moistened with mild detergent. To avoid possible damage on device body coating which could cause performance decrease, do not use volatile solvent such as alcohol, benzene, diluent and so on to clean the device body, nor can strong, abrasive detergent be used.
  • Page 6 Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Introduction 6...
  • Page 7 Table of Contents Foreword ..............................2 Important Safeguards and Warnings ......................4 Regulatory Information ..........................5 FCC Information ............................5 1 Introduction ............................8 1.1 Cable ............................. 8 1.2 Connecting Alarm Input/output ...................... 9 2 Network Configuration ........................11 2.1 Initializing Device ......................... 11 2.2 Modifying Device IP Address .......................
  • Page 8 Introduction 1.1 Cable Cable type might vary with different devices, and the actual product shall prevail. Please waterproof all the cable joints with insulating tape and waterproof tape to avoid short circuit and water damage. For the detailed operation, see the FAQ Manual. Figure 1-1 Cable list For more information about cable ports, see Table 1-1.
  • Page 9 Inputs 12V DC power. Please be sure to supply power as instructed in the Guide. 12V DC power input Device abnormity or damage could occur if power is not supplied correctly. For more information about I/O port, see Table 1-2. Table 1-2 Alarm information Port Port Name...
  • Page 10 up voltage) after adding external pull-up resistor; the output signal becomes low level when there is alarm output. The operating current of alarm output port is recommended to be less than 10mA. The max current which is used to drive external circuit is 80mA, it is recommended to add relay externally when it is beyond the value.
  • Page 11 Introduction Network Configuration Device initialization and IP setting can be finished with the "IP Finder" or in web interface. For more information, see the WEB Operation Manual. Device initialization is available on select models, and it is required at first use and after device is being reset.
  • Page 12 Step 3 Click Search setting. The Setting interface is displayed. Step 4 Enter the start IP and end IP of the network segment in which you want to search devices, and then click OK. All the devices found in the network segment are listed. Step 5 Select one or several devices which Status are Uninitialized, and then click Initialize.
  • Page 13 Modifying IP addresses in batch is available only when the corresponding devices have the same login password. Step 1 Follow Step 1 to Step 4 in 2.1 to search devices in your network segment. After clicking Search setting, please make sure the username and password are the same as what you set during initialization, otherwise there will be "wrong password"...
  • Page 14 2.3 Logging in Web Interface Step 1 Open IE browser enter the IP address of the device in the address bar and press Enter. If the setup wizard is displayed, follow the instructions to finish the settings. Step 2 Enter user name and password in the login box, and then click Login. Step 3 For first time login, click Click Here to Download Plugin and install the plugin as instructed.
  • Page 15 3.2 Dimension Following figures are for reference only, the actual product shall prevail. (Unit: mm [in]) Installation...
  • Page 16 3.3 Installing Device 3.3.1 Installation method、...
  • Page 17 3.3.2 Installing SD Card (Optional) SD card slot is available on select models. Disconnect the power from the device before installing the SD card. Pressing reset button: Short press reset button for 1-2 s, press WPS button on the router and the device can be connected to corresponding router within 1 minute (only supported by some models).
  • Page 19 Option 2: -Cable going through the side cable tray 3.3.4 Installing Waterproof Connector This part is only needed when there is waterproof connector come with the device and the device is used outdoor.
  • Page 20 3.3.5 Adjusting Angle Vertical rotation ring is available on select models, which fails to support image rotation. Please refer to the real model for more details. IR light layout is different according to different models; please refer to the real model for more details.
  • Page 21 Thank You for choosing CP PLUS!!! Website: - www.cpplusworld.com Email id: - sales@cpplusworld.com; support@cpplusworld.com...

This manual is also suitable for:

Orange cp-unc-vb51l3c-mdsOrange cp-unc-vb41l3c-mds