Source SEM-BH P04 Installation Instructions

DISASSEMBLY INSTRUCTIONS
e below. For the cable color of power cable, I just give a suggestion to you ,you can change it according to your local regulation
So, Please reivse wiring diagram as the below. For the cable color of power cable, I just give a suggestion to you ,you can change it according to your local regulation
So, Please reivse wiring diagram as the below. For the cable color of power cable, I just give a suggestion to you ,you can change it according to your local regulation
you can change it to Brown according to your local regulation. It depends on your local usage
Example,my diagram is L -BLACK, but you can change it to Brown according to your local regulation. It depends on your local usage
Example,my diagram is L -BLACK, but you can change it to Brown according to your local regulation. It depends on your local usage
So, Please reivse wiring diagram as the below. For the cable color of power cable, I just give a suggestion to you ,you can change it according to your local regulation
Example,my diagram is L -BLACK, but you can change it to Brown according to your local regulation. It depends on your local usage
Product end of life instruction.
This Lighting product is in the scope of EU 2019/2020 directive on Waste Electrical and Electronic Equipment
(WEEE). This product must be disposed of, according to the legislation. This document is intended for use by
end of life recyclers or treatment facilities. It provides the basic information to assure an appropriate end of life
treatment for the components and materials of the product.
Please follow pictured diagram on the back of this manual showing how to dismantle the product into different
components which should be disposed of correctly. These components consist of plastic, metal and electronic
materials.
It is the responsibility of the end user to dispose of this product correctly. Contact www.weeeireland.ie or your
local council for further information.
Loosen screws with
SEM-BH P04
SEM-BH P04
ording to your local usage, but you can not change link wire to connector.
You can change power cable color according to your local usage, but you can not change link wire to connector.
SEM-BH P04
You can change power cable color according to your local usage, but you can not change link wire to connector.
bring confusion to customer. Please amend
It will not match product wiring, it will bring confusion to customer. Please amend
It will not match product wiring, it will bring confusion to customer. Please amend
You can change power cable color according to your local usage, but you can not change link wire to connector.
It will not match product wiring, it will bring confusion to customer. Please amend
Dismantle middle plate
Unit 7/8 Ashbourne Business Centre, Ballybin Road, Ashbourne, Co. Meath, Ireland, A84 YP58,
For more information contact: Phone: 00353 1 835 7447
Unit 32 Junction One Business Park, Valley Road, Birkenhead, Merseyside, UK, CH41 7ED,
UK Ph: 0330 551 7000
Website:
SAFETY This is a mains powered product. It is designed to be installed by a qualified electrician and in accordance with the
applicable building and electrical regulations. Before installation or maintenance the electrical supply to the product must be
isolated.
WARRANTY This product is warranted to be free of defects in materials, design and workmanship for 5 years from the date of
purchase. This warranty does not include batteries or consumable items such as fuses. The NiCd Battery has a 2 year warranty.
The LiFeP04 has a 3 year warranty.
LUMINAIRE INSTALLATION
Loose screw by screwdriver
screwdriver
Dismantle middle plate
Dismantle battery,
driver and LED plate
OPERATION / MAINTENANCE
RECESSED MOUNT KIT INSTALLATION –
IP65
www.sgd.ie
Quality
Assurance
EMERGENCY BULKHEAD INSTRUCTIONS
SAFETY This is a mains powered product. It is designed to be installed by a qualified electrician and in accordance with the
applicable building and electrical regulations. Before installation or maintenance the electrical supply to the product must be
isolated.
SAFETY This is a mains powered product. It is designed to be installed by a qualified electrician and in accordance with the
applicable building and electrical regulations. Before installation or maintenance the electrical supply to the product must be
WARRANTY This product is warranted to be free of defects in materials, design and workmanship for 5 years from the date of
isolated.
purchase. This warranty does not include batteries or consumable items such as fuses. The NiCd Battery has a 2 year warranty.
The LiFeP04 has a 3 year warranty.
WARRANTY This product is warranted to be free of defects in materials, design and workmanship for 5 years from the date of
purchase. This warranty does not include batteries or consumable items such as fuses. The NiCd Battery has a 2 year warranty.
LUMINAIRE INSTALLATION
The LiFeP04 has a 3 year warranty.
1.
1.
Remove diffuser by unscrewing the two screws.
Remove diffuser by unscrewing the two screws.
LUMINAIRE INSTALLATION
2.
2.
Hinge the gear tray open by pushing apart the two retaining clips.
Hinge the gear tray open by pushing apart the two retaining clips.
3. 3.
Screw fix the base to the chosen mounting surface using the two screw Screw fix the base to the chosen mounting surface using the two screw
1.
Remove diffuser by unscrewing the two screws.
fixing points in the base moulding at 240mm centres. These should be fixing points in the base moulding at 240mm centres. These should be
2.
Hinge the gear tray open by pushing apart the two retaining clips.
drilled to a size to suit the fixing screws.
drilled to a size to suit the fixing screws.
3.
Screw fix the base to the chosen mounting surface using the two screw
Note: It is responsibility of the installer to ensure these fixing points Note: It is responsibility of the installer to ensure these fixing points
fixing points in the base moulding at 240mm centres. These should be
are sealed to ensure the IP65 rating is maintained. The use of a are sealed to ensure the IP65 rating is maintained. The use of a
drilled to a size to suit the fixing screws.
silicone sealant is recommended. silicone sealant is recommended.
Note: It is responsibility of the installer to ensure these fixing points
4.
4.
Select one of the available cable entry points on the base (one on either
Select one of the available cable entry points on the base (one on either
are sealed to ensure the IP65 rating is maintained. The use of a
end, on one side, or through the bottom) & drill to suitable size to suit IP65 end, on one side, or through the bottom) & drill to suitable size to suit IP65
silicone sealant is recommended.
rated (or better) cable entry gland (not provided). 4. rated (or better) cable entry gland (not provided).
Select one of the available cable entry points on the base (one on either
5. 5.
Install cable entry gland. Install cable entry gland.
end, on one side, or through the bottom) & drill to suitable size to suit IP65
6.
6.
Depending on which variant of the product you have, determine your
Depending on which variant of the product you have, determine your
rated (or better) cable entry gland (not provided).
5.
required function & route the appropriate power supply cable to the terminal required function & route the appropriate power supply cable to the terminal
Install cable entry gland.
block & terminate as shown. 6. block & terminate as shown.
Depending on which variant of the product you have, determine your
required function & route the appropriate power supply cable to the terminal
block & terminate as shown.
Plug in Connector
7. If applicable, tighten cable gland to seal & secure mains cable. 7. If applicable, tighten cable gland to seal & secure mains cable.
8. Connect the battery pack to the PCB by connecting the female socket on the battery wires to the male plug mounted on
8. Connect the battery pack to the PCB by connecting the female socket on the battery wires to the male plug mounted on
the PCB, ensuring the correct orientation. the PCB, ensuring the correct orientation.
7. If applicable, tighten cable gland to seal & secure mains cable.
9. Enter the "Installation Date" in the appropriate place on the battery pack label. 9. Enter the "Installation Date" in the appropriate place on the battery pack label.
8. Connect the battery pack to the PCB by connecting the female socket on the battery wires to the male plug mounted on
10. Hinge the gear tray closed & snap fit of clips to secure. 10. Hinge the gear tray closed & snap fit of clips to secure. the PCB, ensuring the correct orientation.
Dismantle battery,driver, led
11. Refit the diffuser & secure using the two screws.
11. Refit the diffuser & secure using the two screws. 9. Enter the "Installation Date" in the appropriate place on the battery pack label.
12. Reconnect the power supply & check the green LED charge indicator illuminates. 10. Hinge the gear tray closed & snap fit of clips to secure. 12. Reconnect the power supply & check the green LED charge indicator illuminates.
plate
13. The batteries should be allowed to charge for at least 24 hours before carrying out a full discharge test to check they are 11. Refit the diffuser & secure using the two screws. 13. The batteries should be allowed to charge for at least 24 hours before carrying out a full discharge test to check they are
charging correctly & the maintained duration is being achieved. 12. Reconnect the power supply & check the green LED charge indicator illuminates. charging correctly & the maintained duration is being achieved.
13. The batteries should be allowed to charge for at least 24 hours before carrying out a full discharge test to check they are
OPERATION / MAINTENANCE charging correctly & the maintained duration is being achieved.
1. NiCd battery life is 2 years, after which time it should be replaced with a suitable equivalent. TheP04LiFe battery 1. NiCd battery life is 2 years, after which time it should be replaced with a suitable equivalent. TheP04LiFe battery
should be changed after 3 years.
should be changed after 3 years.
OPERATION / MAINTENANCE
2. This luminaire MUST be disconnected before it is subjected to any high voltage or insulation resistance testing, 1. 2. NiCd battery life is 2 years, after which time it should be replaced with a suitable equivalent. TheP04LiFe battery This luminaire MUST be disconnected before it is subjected to any high voltage or insulation resistance testing,
otherwise irreparable damage will occur to luminaire components. should be changed after 3 years. otherwise irreparable damage will occur to luminaire components.
3. 3.
2. This luminaire MUST be disconnected before it is subjected to any high voltage or insulation resistance testing,
Ensure cleanliness of luminaires is maintained so as not to affect performance. Ensure cleanliness of luminaires is maintained so as not to affect performance.
otherwise irreparable damage will occur to luminaire components.
RECESSED MOUNT KIT INSTALLATION – 3.
Ensure cleanliness of luminaires is maintained so as not to affect performance.
1. Prepare ceiling by cutting suitable size aperture. We recommend 360mm x 110mm.
1. Prepare ceiling by cutting suitable size aperture. We recommend 360mm x 110mm.
RECESSED MOUNT KIT INSTALLATION –
2. Bend springs up to vertical & push the back of the frame up through aperture, then allow the springs to snap back 2. Bend springs up to vertical & push the back of the frame up through aperture, then allow the springs to snap back
1. Prepare ceiling by cutting suitable size aperture. We recommend 360mm x 110mm.
against the top of the ceiling to retain. against the top of the ceiling to retain.
2. Bend springs up to vertical & push the back of the frame up through aperture, then allow the springs to snap back
3. Drill out the two fixing points at 240mm centres in the base of the luminaire & then secure the base to the frame using 2-
3. Drill out the two fixing points at 240mm centres in the base of the luminaire & then secure the base to the frame using 2-
against the top of the ceiling to retain.
off M4 screws aligned with the tapped holes on the brackets of the frame. off M4 screws aligned with the tapped holes on the brackets of the frame.
3. Drill out the two fixing points at 240mm centres in the base of the luminaire & then secure the base to the frame using 2-
4. Other installation details as per LUMINAIRE INSTALLATION section above. 4. Other installation details as per LUMINAIRE INSTALLATION section above.
off M4 screws aligned with the tapped holes on the brackets of the frame.
4. Other installation details as per LUMINAIRE INSTALLATION section above.
COMPLIANT
Installation Instructions
years
EMERGENCY SELF TESTING
EMERGENCY BULKHEAD INSTRUCTIONS
BULKHEAD
PRODUCT CODE: SEM-BH P04
EMERGENCY BULKHEAD INSTRUCTIONS
SAFETY This is a mains powered product. It is designed to be installed by a qualified electri
applicable building and electrical regulations. Before installation or maintenance the electrica
isolated.
WARRANTY This product is warranted to be free of defects in materials, design and workmansh
purchase. This warranty does not include batteries or consumable items such as fuses. The NiC
The LiFeP04 has a 3 year warranty.
LUMINAIRE INSTALLATION
1.
Remove diffuser by unscrewing the two screws.
2.
Hinge the gear tray open by pushing apart the two retaining clips.
3.
Screw fix the base to the chosen mounting surface using the two screw
fixing points in the base moulding at 240mm centres. These should be
drilled to a size to suit the fixing screws.
Note: It is responsibility of the installer to ensure these fixing points
are sealed to ensure the IP65 rating is maintained. The use of a
silicone sealant is recommended.
4.
Select one of the available cable entry points on the base (one on either
end, on one side, or through the bottom) & drill to suitable size to suit IP65
rated (or better) cable entry gland (not provided).
5.
Install cable entry gland.
6.
Depending on which variant of the product you have, determine your
required function & route the appropriate power supply cable to the terminal
block & terminate as shown.
BLUE
BLUE
BLACK
BROWN
BROWN
GREEN & YELLOW
GREEN & YELLOW
Remove Connector
7. If applicable, tighten cable gland to seal & secure mains cable.
8. Connect the battery pack to the PCB by connecting the female socket on the battery wir
the PCB, ensuring the correct orientation.
9. Enter the "Installation Date" in the appropriate place on the battery pack label.
10. Hinge the gear tray closed & snap fit of clips to secure.
11. Refit the diffuser & secure using the two screws.
12. Reconnect the power supply & check the green LED charge indicator illuminates.
13. The batteries should be allowed to charge for at least 24 hours before carrying out a full
charging correctly & the maintained duration is being achieved.
OPERATION / MAINTENANCE
1. NiCd battery life is 2 years, after which time it should be replaced with a suitable equiva
should be changed after 3 years.
2. This luminaire MUST be disconnected before it is subjected to any high voltage or insula
otherwise irreparable damage will occur to luminaire components.
3.
Ensure cleanliness of luminaires is maintained so as not to affect performance.
RECESSED MOUNT KIT INSTALLATION –
1. Prepare ceiling by cutting suitable size aperture. We recommend 360mm x 110mm.
2. Bend springs up to vertical & push the back of the frame up through aperture, then allow
against the top of the ceiling to retain.
3. Drill out the two fixing points at 240mm centres in the base of the luminaire & then secu
off M4 screws aligned with the tapped holes on the brackets of the frame.
4. Other installation details as per LUMINAIRE INSTALLATION section above.
EMERGENCY BULKHEAD INSTRUCTIONS
EMERGENC
SAFETY This is a mains powered product. It is de
applicable building and electrical regulations. Befo
isolated.
WARRANTY This product is warranted to be free of
purchase. This warranty does not include batteries o
The LiFeP04 has a 3 year warranty.
LUMINAIRE INSTALLATION
1.
Remove diffuser by unscrewing the two scre
2.
Hinge the gear tray open by pushing apart t
3.
Screw fix the base to the chosen mounting s
fixing points in the base moulding at 240mm
drilled to a size to suit the fixing screws.
Note: It is responsibility of the installer to
are sealed to ensure the IP65 rating is ma
silicone sealant is recommended.
4.
Select one of the available cable entry point
end, on one side, or through the bottom) & d
rated (or better) cable entry gland (not provi
5.
Install cable entry gland.
6.
Depending on which variant of the product y
required function & route the appropriate po
block & terminate as shown.
BLUE
BROWN
GREEN & YELLOW
Remove Connector
7. If applicable, tighten cable gland to seal & s
8. Connect the battery pack to the PCB by con
the PCB, ensuring the correct orientation.
9. Enter the "Installation Date" in the appropria
10. Hinge the gear tray closed & snap fit of clips
11. Refit the diffuser & secure using the two scr
12. Reconnect the power supply & check the gr
13. The batteries should be allowed to charge fo
charging correctly & the maintained duration
OPERATION / MAINTENANCE
1.
NiCd battery life is 2 years, after which time
should be changed after 3 years.
2. This luminaire MUST be disconnected befor
otherwise irreparable damage will occur to l
3.
Ensure cleanliness of luminaires is maintain
RECESSED MOUNT KIT INSTALLATION –
1. Prepare ceiling by cutting suitable size aper
2. Bend springs up to vertical & push the back
against the top of the ceiling to retain.
3. Drill out the two fixing points at 240mm cent
off M4 screws aligned with the tapped holes
4. Other installation details as per LUMINAIRE