Philips S5898, S5889, S5882, S5881, S5898/50 - Electric Shaver Manual
![]()
Introduction
Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome or via the app.
General description
![Philips - S5898 - General description General description]()
- Pop-up trimmer
- Trimmer release slide
- Shaving unit
- Shaving unit release button
- On/off button
- Handle
- Socket for small plug
- Charging stand (specific models only)
- USB cable
Note: A suitable supply unit (e.g. Philips HQ87) is available via www.philips.com/support. - Protection cap
- Pouch
- Quick Clean Pod Cartridge (specific models only)
- Quick Clean Pod (specific models only)
- Cleaning brush
Note: The accessories supplied may vary for different products. The box shows the accessories that have been supplied with your appliance.
What do the icons on my appliance handle mean?
Icon | Behavior | Meaning |
![]() | Flashing | Clean the appliance under the tap (see 'How do I clean my appliance and the attachments?'). |
![]() | Flashing when you press the on/off button | The travel lock is activated. |
![]() | Lights up when you pick up the appliance | The number of bars lit up show the remaining battery charge. |
![]() | Bottom light flashing orange | The battery is almost empty (see 'How do I charge my appliance?'). |
![]() | Lights flashing in sequence | The appliance is charging. |
![]() | Lights up continuously | The appliance is fully charged. |
![]() | Flashing | The appliance must be disconnected from the wall socket before you can switch it on (see 'How do I charge my appliance?'). |
What does the icon on my Quick Clean Pod mean? (specific models only)
Icon | Behavior | Meaning |
![]() | Becomes visible on the Quick Clean Pod | The Quick Clean Pod Cartridge needs to be replaced. |
How do I charge my appliance?
Charge the appliance before you use it for the first time and when the bottom light of the battery status indicator flashes orange, indicating that the battery is almost empty. Charging takes approx. 1 hour. Quick Charge: After approx. 5 minutes of charging, the battery contains enough energy for one full shave. When the appliance is fully charged it has a cordless operating time of up to 60 minutes.
Note: You cannot use the appliance while it is charging.
Charging with the supply unit
![]()
Keep the USB cable and the USB supply unit dry.
- Make sure that the appliance is switched off.
- Insert the small plug of the USB cable into the socket in the bottom of the appliance.
- Insert the USB plug into the USB supply unit (not provided).
![]()
- Insert the USB supply unit into the wall socket.
- While the appliance is in quick charge mode, the lights of the battery status indicator light up one after the other. After approximately 5 minutes, the bottom light of the battery status indicator flashes. The battery now contains enough energy for one full shave.
- While the appliance charges, first the bottom light of the battery status indicator flashes and then lights up continuously. Next the second light flashes and then lights up continuously, and so on until the appliance is fully charged.
- When the appliance is fully charged, all three battery indicator lights light up continuously. After approx. 30 minutes, the light goes out automatically.
- After charging, remove the USB supply unit from the wall socket, pull the USB plug out of the supply unit and then pull the small plug out of the appliance.
Charging in the charging stand (specific models only)
![]()
Keep the USB cable, the USB supply unit and the charging stand dry.
- Make sure the appliance is switched off.
- Insert the small plug of the USB cable into the charging stand.
![]()
- Insert the USB plug into the USB supply unit (not provided).
![]()
- Insert the USB supply unit into the wall socket.
- Place the appliance in the charging stand. Specific models only: The light ring on the bottom of the charging stand lights up and rotates quickly.
- After approximately 5 minutes, the light ring rotates slower. The battery now contains enough energy for one full shave.
- As the appliance continues to charge, the light ring becomes brighter and rotates slower. - When the appliance is fully charged, the light ring lights up fully and stops rotating.
- After charging, remove the USB supply unit from the wall socket and pull the small plug out of the charging stand.
'Unplug for use' symbol
The 'unplug for use' symbol flashes to remind you to disconnect the appliance from the wall socket and remove the small plug from the appliance before you switch it on.
![]()
How do I use my appliance and the attachments?
![]()
Always check the appliance and all accessories before use. Do not use the appliance or any accessory if it is damaged, as this may cause injury. Always replace a damaged part with one of the original type.
Note: This appliance is waterproof. It is suitable for use in the bath or shower and for cleaning under the tap. For safety reasons, the appliance can therefore only be used without cord.
Shaving
You can use this appliance either wet or dry, or even under the shower. For a wet shave, apply some water and shaving foam or gel to your skin and rinse the shaving heads under the tap with warm water before following the steps below.
- Switch on the appliance.
![]()
- Move the shaving heads over your skin in circular movements to catch all hairs growing in different directions. Make sure each shaving head is fully in contact with the skin. Exert gentle pressure for a close, comfortable shave. Note: Do not press too hard, as this can cause skin irritation.
Note: If you are shaving with gel or foam, rinse the shaving unit regularly during your shave to ensure that it continues to glide smoothly over your skin.
![]()
- Use the narrow sides of the shaving unit to shave in hard-to-reach areas such as along your jawline and under your nose.
![]()
- Switch off and clean the appliance after each use.
Note: Make sure you rinse all foam or shaving gel off the appliance.
Skin adaptation period
Your first shaves may not bring you the result you expect and your skin may even become slightly irritated. This is normal. Your skin and beard need time to adapt to any new shaving system. To allow your skin to adapt to this new appliance, we advise you to shave regularly (at least 3 times a week) and exclusively with this appliance for a period of 3 weeks.
Cleaning reminder
When you switch off the appliance, the cleaning reminder flashes to remind you to clean the appliance.
![]()
- Clean the appliance and attachments after each use to prevent clogging and damage (see 'How do I clean my appliance and the attachments?').
- Clean the shaving heads thoroughly once a month or when the appliance does not shave as well as it used to (see 'Thorough cleaning').
Trimming
You can use the trimmer to groom your sideburns and moustache.
- Push the trimmer release slide downwards to open the trimmer.
![]()
- Switch on the appliance.
- Hold the trimmer perpendicular to the skin and move the appliance downwards while you exert gentle pressure.
![]()
- You can also use the trimmer under your nose.
![]()
- Switch off the appliance and clean the trimmer after each use to prevent clogging and damage (see 'How do I clean my appliance and the attachments?').
- Close the trimmer.
How do I clean my appliance and the attachments?
Clean the appliance and the attachments after each use for optimal performance.
Cleaning the shaver under the tap
Clean the shaver after each use to prevent clogging and damage.
Never dry the shaving unit with a towel or tissue, as this may damage the shaving heads. While rinsing the shaving unit, water may drip out of the base of the shaver. This is a normal occurrence.
- Switch on the shaver.
- Rinse the shaving unit under a warm tap.
![]()
- Switch off the shaver. Press the release button to open the shaving unit.
![]()
- Rinse the hair chamber under a warm tap.
![]()
- Rinse the shaving head holder under a warm tap.
- Carefully shake off excess water and let the shaving head holder air-dry completely.
![]()
- Close the shaving unit.
![]()
Thorough cleaning
We advise you to clean the shaving heads thoroughly once a month or when the shaver does not shave as well as it used to.
- Make sure that the appliance is switched off and disconnected from the wall socket.
- Press the release button on the shaving unit and pull the shaving head holder off the shaving unit.
![]()
- Rinse the hair chamber and shaving head holder under the tap.
- Remove the shaving heads. For detailed instructions, see 'How do I replace the shaving heads?'. Note: Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally put a cutter in the wrong shaving guard, it may take several weeks before optimal shaving performance is restored.
![]()
- Clean the cutter and guard under the tap.
![]()
- Shake off excess water.
- Put the shaving heads back into the shaving unit. For detailed instructions, see 'How do I replace the shaving heads?'.
- Insert the hinge of the shaving head holder into the slot in the top of the shaving unit and close the shaving unit.
![]()
Cleaning the pop-up trimmer
Clean the trimmer after each use to prevent clogging and damage. Never dry the trimmer teeth with a towel or tissue, as this may damage the trimmer teeth.
- Make sure that the appliance is switched off and disconnected from the wall socket.
- Push the trimmer release slide down to open the popup trimmer.
![]()
- Switch on the appliance and rinse the pop-up trimmer with warm water.
- After cleaning, switch off the appliance.
![]()
- Carefully shake off excess water and let the pop-up trimmer air dry.
- Close the trimmer.
![]()
Tip: For optimal performance, lubricate the teeth of the pop-up trimmer with a drop of mineral oil every six months (oil not included).
How do I use the Quick Clean Pod? (specific models only)
Preparing the Quick Clean Pod for use
- Twist and remove the top of the Quick Clean Pod.
![]()
- Twist the lid off of the Quick Clean Pod Cartridge.
![]()
- Lift the tab on the seal and pull it by the corner to remove the seal from the Quick Clean Pod Cartridge.
![]()
- Press the small circular piece on the handle of the Quick Clean Pod Cartridge to break the snap hook on the handle.
![]()
- Place the Quick Clean Pod Cartridge into the Quick Clean Pod.
![]()
- Put the top of the Quick Clean Pod back onto the base and turn it clockwise until you hear a click.
![]()
Do not tilt the Quick Clean Pod to prevent leakage.
![]()
Using the Quick Clean Pod (specific models only)
Note: If you use the shaver with shaving foam, shaving gel or pre-shave products, thoroughly rinse the shaving heads before you use the Quick Clean Pod (see 'How do I clean my appliance and the attachments?').
Always shake excess water off the shaver before you place it in the Quick Clean Pod.
- Place the shaver upside down into the Quick Clean Pod. The shaver automatically detects that it is in the Quick Clean Pod.
![]()
- Switch on the shaver to start the cleaning program.
Each cleaning program takes approximately one minute. During the cleaning program the cleaning symbol lights up continuously and the blue icon pulses. The shaver handle vibrates twice quickly when the cleaning program is finished.
![]()
- Let the shaver air-dry completely in the Quick Clean Pod before storing it.
Replacing the Quick Clean Pod Cartridge (specific models only)
Replace the Quick Clean Pod Cartridge immediately when the cartridge replacement icon on the Quick Clean Pod becomes visible or follow the table below.
![]()
Frequency of use | Cycles | When to replace the Quick Clean Pod Cartridge |
Every day | About 30 | Every month |
A few times per week | About 20 | Every 2 months |
Every week | About 13 | Every 3 months |
Every month | About 3 | Every 3 months |
- Twist and remove the top of the Quick Clean Pod.
![]()
- Lift the Quick Clean Pod Cartridge out of the Quick Clean Pod by the handle.
![]()
- Pour any remaining fluid down a drain and recycle the empty cartridge in accordance with local waste regulations.
![]()
- Place a new Quick Clean Pod Cartridge into the Quick Clean Pod (see 'Preparing the Quick Clean Pod for use'). Scan the QR code to the left or visit www.philips.com/cleaning-cartridge to order replacement Quick Clean Pod Cartridges.
![]()
How do I replace the shaving heads?
For maximum shaving performance, replace the shaving heads once a year. Replace damaged shaving heads immediately. Always replace the shaving heads with original Philips shaving heads (see 'Ordering accessories').
Replacing the shaving heads
![]()
- Switch off the shaver.
- Press the release button on the shaving unit and pull the shaving head holder off the shaving unit.
- Turn the retaining rings anticlockwise and remove them. Place them aside in a safe place.
![]()
- Remove the shaving heads from the shaving head holder. Discard the used shaving heads immediately to avoid mixing them with the new shaving heads.
![]()
- Place new shaving heads in the holder.
![]()
- Place the retaining rings back onto the shaving heads and turn them clockwise to reattach the retaining rings.
- Each retaining ring has two recesses that fit exactly into the projections of the shaving head holder. Turn the ring clockwise until your hear a click to indicate that the ring is fixed.
![]()
- Insert the hinge of the shaving head holder into the slot in the top of the shaving unit and close the shaving unit.
![]()
Ordering accessories
To buy accessories or spare parts, visit www.philips.com/parts-and-accessories or go to your Philips dealer. You can also contact the Philips Consumer Care Center in your country (see the international warranty leaflet for contact details). The following accessories and spare parts are available: - SH71 replacement Philips shaving heads - CC13 Philips Quick Clean Pod Cartridge 3-pack
Note: The availability of the accessories may differ by country.
Removal of built-in rechargeable battery
The built-in rechargeable battery must only be removed by a qualified professional when the appliance is discarded. Before removing the battery, make sure that the appliance is disconnected from the wall socket and that the battery is completely empty. Take any necessary safety precautions when you handle tools to open the appliance and when you dispose of the rechargeable battery. When you handle batteries, make sure that your hands, the product and the batteries are dry.
To avoid accidental short-circuiting of batteries after removal, do not let battery terminals come into contact with metal objects (e.g. coins, hairpins, rings). Do not wrap batteries in aluminum foil. Tape battery terminals or put batteries in a plastic bag before you discard them. Be careful, the battery strips are sharp.
- Twist the shaving head to remove it from the handle.
![]()
- Insert a flat-head screwdriver under the rim of the panel and pry off.
![]()
- Remove the two screws from the top with a torx or flat-head screwdriver.
![]()
- Slide the front shell off.
![]()
- Break the bridge on top with a wire cutter.
![]()
- Insert a flat head screwdriver on either side of the shaver body to release the hooks.
![]()
- Slide the power unit out of the body.
![]()
- Bend the snap hooks aside and remove the transparent cover of the power unit.
![]()
- Lift out out the battery holder and cut the wires with a pair of cutting pliers or scissors.
![]()
- Bend the battery tags aside with a pair of cutting pliers or a screwdriver.
![]()
- Remove the rechargeable battery.
Only use the product for its intended purpose. Read this important information carefully before you use the product and its batteries and accessories, and save it for future reference. Misuse can lead to hazards or serious injuries. Accessories supplied may vary for different products.
![]()
- To charge the product, only use a certified safety extra low voltage (SELV) supply unit with output rating 5 V, ≥ 1 A. For safe charging in a moist environment (e.g. in a bathroom), only use an IPX4 (splash-proof) supply unit. A suitable supply unit (e.g. Philips HQ87) is available via www.philips.com/support. If you need support finding the correct USB supply unit, contact Philips support at +1 (866) 800 9311. Using a noncertified supply unit may cause hazards or serious injuries.
- Keep the USB cable, the USB supply unit and the charging stand dry.
![]()
- This shaver is waterproof. It is suitable for use in the bath or shower and for cleaning under the tap. For safety reasons, the shaver can therefore only be used without cord.
![]()
- Do not modify the supply unit.
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
- Unplug the appliance before cleaning it with water.
- Do not use a damaged appliance. Replace damaged parts with new Philips parts.
- Only use cold or lukewarm water to clean the appliance.
- Because of hygiene, only one person should use the appliance.
- Never use compressed air, scouring pads, abrasive cleaning agents or aggressive liquids to clean the appliance.
- Always place the cleaning system on a stable, level and horizontal surface to prevent leakage.
- Always make sure the cartridge compartment is closed before you use the cleaning system.
- When the cleaning system is ready for use, do not move it to prevent leakage of cleaning fluid.
- Water may drip from the socket at the bottom of the shaver when you rinse it. This is normal and not dangerous because all electronics are enclosed in a sealed power unit inside the shaver.
- Do not use the supply unit in or near wall sockets that contain an electric air freshener to prevent irreparable damage to the supply unit.
- Only use original Philips accessories or consumables.
- Charge, use and store the product at a temperature between 5°C and 35°C.
- Keep product and batteries away from fire and do not expose them to direct sunlight or high temperatures.
- If the product becomes abnormally hot or smelly, changes color or if charging takes longer than usual, stop using and charging the product and contact Philips.
- Do not place products and their batteries in microwave ovens or on induction cookers.
- Do not open, modify, pierce, damage or dismantle the product or battery to prevent batteries from heating up or releasing toxic or hazardous substances. Do not short-circuit, overcharge or reverse charge batteries.
- If batteries are damaged or leaking, avoid contact with the skin or eyes. If this occurs, immediately rinse well with water and seek medical care.
Philips Quick Clean Pod Cartridge fluid
- Keep out of reach of children.
- Do not swallow.
Electromagnetic fields (EMF)
This Philips appliance complies with all applicable standards and regulations regarding exposure to electromagnetic fields.
Documents / Resources
References
Download manual
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Download Philips S5898, S5889, S5882, S5881, S5898/50 - Electric Shaver Manual
Need help?
Do you have a question about the S5898 and is the answer not in the manual?
Questions and answers