PowerA MOGA XP5-A PLUS - Bluetooth Controller Manual

PARTS AND FEATURES

SETUP

For best results, fully charge controller and power bank prior to first use.

CHARGING CONTROLLER + POWER BANK

• Using the included 6.6 ft. (2 m) USB Cable, connect the Micro-USB end to lower port at top of the controller, and connect the Standard USB end to any powered USB source.
• When charging, four LEDs will display the charging level from 25-50-75-100%.

CHARGE LEVEL INDICATOR

Check battery charge level by pressing the battery status button ( ) on front lower left of controller. The LEDs will indicate the current charge level from 25-100% even when controller is off.

WIRELESS MODE

Move Wireless/Wired switch on front center of controller to BT ( ) which indicates Bluetooth wireless mode.

• If controller is off, press the MENU button ( ) to turn on (LED will illuminate).
• Press and hold the Bluetooth sync button ( ) on top of controller for 2 seconds to enter pairing mode (LED will flash rapidly).
• Enter the Bluetooth settings on your device and choose the MOGA controller. The pairing LED will turn solid when connected.

NOTE: A previously paired device will automatically pair to the controller when powered on.

POWERING OFF

Hold the menu button ( ) for 5 seconds to turn controller off and save battery capacity.

WIRED MODE

Move Wireless/Wired switch on front center of controller to USB ( ) which indicates wired mode.

• Connect Micro-USB end of the 11.8" (30 cm) or 6.5ft (2 m) cable to lower port at top of controller, and connect other end to your gaming device.
• Gaming device input ports (Standard USB, Micro-USB, USB-C) will determine whether you use shorter or longer micro-USB cable for wired gaming.
• This MOGA controller supports Direct Input by default, but also supports XInput mode. If initial wired connection is unsuccessful, switch modes by pressing Start + Select for three seconds. Three LED flashes indicate mode was changed and retained in memory. Repeat process to switch back.

GAMING CLIP

A detachable gaming clip is included for use with gaming on your phone. You can use USB cables with clip attached for charging or wired mode.

1. Slide MOGA Controller into gaming clip by tipping top edge in first.
2. Push controller bottom edge down into clip until it locks into notch on front edge of controller.
3. To insert phone, push top edge of phone against top of phone grip to expand upward.
4. Push bottom of phone down flat into place as you reach top limit of phone grip.
5. Adjust phone horizontally to center alignment over controller, and adjust viewing angle forward or back.
6. Open kickstand on clip when setting controller down between sessions to prevent tipping.
7. Remove clip by pulling front edge forward to release from notch.

INTEGRATED POWER BANK

A Power Bank built into the controller allows you to charge your phone during gameplay or while controller is off.

• Connect Standard USB end of the 11.8" (30 cm) cable to upper port at top of controller, and connect other end to your mobile device.
• During gameplay, move the Power Bank switch below right thumbstick to the right (on) to start charging. If you prefer to use battery power to extend controller usage time rather than charge phone, move swith to the left (off).
• To charge mobile device when controller is not in use, simply connect cable between controller and device to begin charging (Power Bank Switch must be ON).
• Your mobile device will display charge status once connected. If charging does not begin, the power bank battery may be too low: recharge controller.
• The amount of charge available for your phone depends on how much battery capacity remains on the controller when charging begins.

ASSIGNING THE ADVANCED GAMING BUTTONS

1. Press the Orange Program Button on the bottom of the controller for 2 seconds. The LED Connection Indicator will flash, signaling the controller is in assign mode.
2. Press 1 of the following buttons (A/B/X/Y/LB/RB/LT/RT/Left Stick Press/Right Stick Press/D-pad) to re-assign. Then press the
   Advanced Gaming Button (AGR or AGL) that you wish to assign. The LED connection indicator will stop flashing, signaling the Advanced Gaming Button has been set.
3. Repeat for the remaining Advanced Gaming Button.

NOTE: Advanced Gaming Button assignments will remain in memory even after disconnected.

RESETTING THE ADVANCED GAMING BUTTONS

• Hold the Program Button down for 2 seconds. The LED Connection Indicator will slowly flash, signaling the controller is in assign mode.
• Press the previously assigned button for 5 seconds, and the function will be cleared.

FAQS

For latest FAQs, visit PowerA.com/Support

PROBLEM: My controller will not power on?
SOLUTION: Confirm the controller is fully charged by pressing the battery status button ( ) on front lower left of controller. Plug in to recharge as needed.

PROBLEM: I do not see MOGA controller listed in mobile devices Bluetooth settings?
SOLUTION: Press and hold the Bluetooth sync button ( ) on back of controller for 2 seconds to enter pairing mode (LED will flash rapidly).

PROBLEM: The integrated power bank is not functioning?
SOLUTION: Confirm the controller has more than 25% charge and Power Bank button is switched on.

CONTACT/SUPPORT

For support with your authentic Power Accessories, please visit PowerA.com/Support.

Documents / Resources

References

• Support | PowerA

Download manual

Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.

Download PowerA MOGA XP5-A PLUS - Bluetooth Controller Manual