Advertisement
Dimensions (W x H x D in mm) | 241 x 519 x 544 |
Case Type | Midi Tower |
Material | 0.7 – 0.8mm SECC steel, 0.8 – 1.2mm aluminum, ABS plastic, 4mm tempered glass |
Motherboard Support | E-ATX (30.5 x 27.5cm), ATX, M-ATX, Mini-ITX |
Front I/O | 2x USB 3.0, 1x USB 3.1 Type C, HD audio (mic + headphone jacks), RGB control switch, 4-step fan controller |
Fan Speed Controller | 6x 4-pin, Step Controller, PWM hub |
Max. Cooler Height (mm) | 180 |
Max. Graphics Card Length (mm) | 286 / 430 (w/o HDD cage) |
PSU Length (mm) | 150 - 285 |
PCI Slots | 7 + 2 |
3.5" Bay | 7 |
2.5" Bay | 3 + 6 |
Cooling Fans (mm) / (rpm) | Front: 1x SilentWings® 3 140mm / 1,600 Rear: 1x SilentWings® 3 140mm / 1,600 |
Optional Cooling Fans | Front: 2x 140/120 Top: 3x 140/120 PSU shroud: 1x 140/120 Bottom: 1x 140/120 |
Radiator Support (mm) | Front: 120, 140, 240, 280, 360 Top: 120, 240, 360 Rear: 120, 140 |
Additional Features | Switchable multi mode, multi color RGB LED lighting at the front panel (white, red, green, blue, orange, purple), support of motherboard LED control |
Images | Part Name | Amount | Usage |
![]() | HDD Cage | 1 | For installing an additional HDD or two further SSDs |
![]() | HDD Decoupling Rubbers | 4 | For installing an additonal HDD slot |
![]() | HDD 6#32 Screws | 12 | HDD mounting |
![]() | M3 Screws | 20 | SSD mounting |
![]() | Screws 6#32 | 8 | Motherboard mounting |
![]() | Fan 6#32 28mm Screws | 4 | Bottom fan mounting |
![]() | Cable Tie | 6 | Cable management |
A | Tempered Glass Window | I | Motherboard Tray |
B | Front Cover PSU Shroud | J | SSD Tray |
C | Top Cover PSU Shroud | K | Fan and LED Controller PCB |
D | HDD Slots | L | External Front Cover |
E | Chassis Body | M | HDD Slot Cover |
F | Front IO Panel | N | Front Air Filter |
G | Base Air Filter | O | Front Panel |
H | SilentWings® 3 Fan | P | Side Panel |
A | Fan Controller Switch | E | Power Button |
B | USB 3.1 Type C | F | HDD LED / Reset |
C | Microphone | G | LED Switch |
D | Headphone | H | USB 3.0 |
The Front I/O ports provided require connections to your motherboard. Refer to your motherboard handbook for information on pin assignments and sockets.
HD audio (headphone jack/microphone jack)
Find the HD audio pin connectors on your motherboard and attach the HD audio cables to the designated sockets.
USB 3.1 Type C
Find the USB 3.1 Type C pin connectors and attach the USB 3.1 Type C cables to the designated sockets.
USB 3.0
Find the USB 3.0 pin connectors on your motherboard and attach the USB 3.0 cables to the designated sockets.
On/Off Switch, Power On LED, Disk Operating LED, Reset Button
The plugs illustrated connect the On/Off Switch and LED lamps of the case to your motherboard. Take care you observe the correct polarity with the LEDs.
A | 4-Pin PWM connector to motherboard |
B | 4-Pin PWM connector to fan |
C | LED connector to motherboard |
D | LED outlet for additional external LEDs |
E | Connecting plug for the front LEDs |
F | SATA power connection |
G | Ports for fan controller switch connector and LED switch on front I/O panel |
H | Switch for choosing between Silence and Performance Mode |
Please note: To ensure proper functioning of the fan control and the LED lighting, make sure that cable F is connected to the power supply.
The fan controller has two modes of operation.
Performance Mode In combination with the Front I/O switch 50% | 800rpm* (Position 1) 70% | 1,120rpm* (Position 2) 100% | 1,600rpm* (Position 3) | Silence Mode In combination with the Front I/O switch 25% | 400rpm* (Position 1) 45% | 640rpm* (Position 2) 65% | 1,040rpm* (Position 3) |
*with SilentWings® 3 1,600rpm
When the slider control is returned to its initial position of "AUTO" the PWM signal of the motherboard resumes control of the fans.
The LED illumination preinstalled in the front can be configured in several colors and operating modes. Further strips of LED illumination for lighting the case interior can be plugged into socket "D" on LED controller PCB with a maximum combined rating of 24 watts.
Only 12V LEDs may be connected.
To switch between synchronized operation and manual control mode keep switch "G" pressed for about three seconds.
Synchronized operation
It is possible to connect cable "C" of the PCB and the corresponding RGB LED controller socket of your motherboard. The integrated illumination can then be controlled by the motherboard.
For information on operation of the LED controller of your motherboard refer to your motherboard handbook.
In manual mode you can cycle through the available colors (white, red, green, blue, orange, purple) by briefly pressing switch "G". An intermediate stage between each color enables "breath mode" for the previously selected color.
The individual switch stages are:
1 | White | 8 | Blue breath |
2 | White breath | 9 | Orange |
3 | Red | 10 | Orange breath |
4 | Red breath | 11 | Purple |
5 | Green | 12 | Purple breath |
6 | Green breath | 13 | Breath mode alternately in all colors |
7 | Blue | 14 | LEDs off |
Position | Fan Size (mm) |
Top | 3x 120, 3x 140 |
Bottom | 1x 120, 1x 140 |
Front | 3x 120, 3x 140 |
Rear | 1x 120, 1x 140 |
PSU Shroud | 1x 120, 1x 140 |
Position | Radiator Size (mm) |
Top | 120, 240, 360 |
Front | 120, 140, 240, 280, 360 |
Rear | 120, 140 |
![]() | To remove the glass side panel, unscrew the four fixing screws as shown |
![]() | To remove the steel side panel, unscrew the two screws as shown and draw the side panel towards the rear with the grip provided for its purpose |
![]() | Install an HDD into the 3.5" slot using the four screws |
![]() | It is possible to install two SSDs (top and bottom) into each HDD slot |
![]() | Remove the SSD tray by unscrewing the fixing screws |
![]() | Affix the SSD and refit the bracket into the case |
![]() | The five HDD slot covers supplied can be mounted in three steps to fully cover the holes or keep them partly open |
![]() | According to requirements, they can be removed or repositioned to install VGA cards or for cable management |
![]() | To optimize the cable routing up to two individual segments of the covers can be „punched out" if necessary.
|
![]() | To remove or clean the air filter the front panel of the case must first be detached. To do this, grasp behind the front edge of the panel from the front and pull it off towards you |
![]() | By depressing the hooks on top, unlatch and remove the front filters as shown |
![]() | Slide out the bottom filter to the front |
Default layout of the Dark Base 700 | Inverted layout of the Dark Base 700 |
![]() | ![]() |
How to switch to inverted layout
![]() | Remove both screws and detach the radiator/ fan bracket from the upper part of the case |
![]() | Remove the nine screws of the motherboard tray |
![]() | Now withdraw the motherboard tray from the case |
![]() | To remove the PSU front panel, depress the centrally marked portion and detach it |
![]() | Remove the four top panels of the PSU cover |
![]() | To dismantle the HDD tray, first remove the two HDD slots by unscrewing each of the three fixing screws |
![]() | Remove the four screws of the HDD tray |
![]() | Remove the HDD tray from the case |
![]() | Now put the HDD tray back on the opposite side and mount it as described in the previous steps |
![]() | Put back the four panels of the PSU cover |
![]() | Now reinsert the motherboard tray into the case and fasten it with the nine previously removed screws |
![]() | Put back the radiator/fan bracket and secure this again with its two screws. Refit the PSU front panel |
![]() | Remove the four screws (including the decoupling rubber) used to mount the glass side panel |
![]() | Refit the screws (including the decoupling rubber) to remount the glass side panel on the opposite side |
Motherboard | |
![]() | Attach the motherboard with the M3 screws supplied. Standoffs are preinstalled for installation of an ATX motherboard |
Test Bench | |
![]() | If required, the motherboard tray can be removed and used as a test bench |
PCI | |
![]() | Before you start to install a PCI / PCI-E addon-card, first remove the PCI slot cover |
VGA | |
![]() | VGA cards can also be installed vertically. The "Raiser Card" that is needed to achieve this is not included in the scope of delivery |
PSU | |
![]() | Place the PSU into the housing and secure it with the screws supplied by the PSU manufacturer |
Top Radiator, Fans | |
![]() | Unscrew the two screws that secure the radiator/fan bracket and slide this out |
![]() | Fit your radiator or fans onto the mounting bracket and secure these with screws as illustrated |
Manufacturer's details
Listan GmbH & Co. KG | Biedenkamp 3a | 21509 Glinde | Germany
For support in Germany, you can call our free service hotline
Monday through Friday 09:00 – 17:30 (UTC+1)
Tel. 0049 40 736 7686 - 44 Fax 0049 40-7367686-69
Email: service@bequiet.com
Internet page: www.bequiet.co
Here you can download full pdf version of manual, it may contain additional safety instructions, warranty information, FCC rules, etc.
Advertisement
Need help?
Do you have a question about the Dark Base 700 and is the answer not in the manual?
Questions and answers