1. Manuals
  2. Brands
  3. TMG Manuals
  4. Outdoor Storage
  5. TMG-ST2041PV
  6. Product manual

TMG -ST2041PV Product Manual

20' x 40' arch wall peak ceiling storage shelter
Hide thumbs

Advertisement

Table of Contents

0/14
TOLL FREE:1-877-761-2819
►www.tmgindustrial.com

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TMG-ST2041PV and is the answer not in the manual?

Questions and answers

Related Manuals for TMG TMG-ST2041PV

Summary of Contents for TMG TMG-ST2041PV

  • Page 1 0/14 TOLL FREE:1-877-761-2819 ►www.tmgindustrial.com...

  • Page 2: Main Specifications

    MAIN SPECIFICATIONS : Overall assembled size : W6.1 x L11.76 x H3.66 (m) / 20 x 38.6x 12 (ft)  Roll up door : W4.3 x H3.2 (m) /14.1 x 10.5 (ft)  CONCRETE FOUNDATION SIZE SEE BELOW FIGURE. The layout of foundation (one). ...
  • Page 3 The layout of foundation(two).  Note: the ground anchor is installed on the cement block. 2/14 TOLL FREE:1-877-761-2819 ►www.tmgindustrial.com...

  • Page 4: Prior To Assembly

    Baseplate layout.  PRIOR TO ASSEMBLY Please read the instructions carefully before installation. It is important to follow your local safety regulations and industry standards during installation. Regulations may include but are not limited to : Safety helmets, protective eyewear, and clothing ...
  • Page 5 TMG-ST2041PV PART LIST PARTS GRAPHICAL DESCRIPTION LENGTH CODE Peak arch tube φ42xL1712mm Middle bent tube φ42xL2145mm Lower bent tube φ42xL2128mm Roof purlin φ42xL1261mm (horizontal tube) Bottom tension tube φ32xL1260mm (for both long bottom sides) Middle truss connectors W50xL180mm Front and rear connectors...

  • Page 6: Installation Steps

    Middle truss baseplate t4xL150xW150mm Tube clamp φ42 Expansion bolt φ14x100mm (not included) Half round head bolt M8x70mm Hex bolt M8x60mm Hex bolt M10x30mm Hex bolt M10x20mm Top cover panel W10920xL12090mm Front and rear cover panel W3700xL6060mm Braided rope φ8xL100m bundle Scratch resistant tape L10m INSTALLATION STEPS...
  • Page 7 STEP 2 : INSTALL BASE PLATES, ALL BASE PLATES MUST BE INSTALLED FIRMLY WITH EXPANSION BOLTS. The diagonal X and Y must be equal.  Installation diagram of expansion bolt.  PART PART 6/14 TOLL FREE:1-877-761-2819 ►www.tmgindustrial.com...
  • Page 8 STEP 3 : ASSEMBLE ALL TRUSSES. PART PART 7/14 TOLL FREE:1-877-761-2819 ►www.tmgindustrial.com...
  • Page 9 STEP 4 : WRAP (#17) AROUND THE SHARP POINTS OF THE JOINT TO AVOID FRICTION BETWEEN THE FABRIC AND THE INTERFACE. PART 8/14 TOLL FREE:1-877-761-2819 ►www.tmgindustrial.com...
  • Page 10 STEP 5 : PUT UP THE ALL TRUSS. PART 9/14 TOLL FREE:1-877-761-2819 ►www.tmgindustrial.com...
  • Page 11 STEP 6 : PUT UP THE REST TRUSSES. PART PART 10/14 TOLL FREE:1-877-761-2819 ►www.tmgindustrial.com...
  • Page 12 STEP 7 : INSTALL THE DIAGONAL BRACING BARS (#6). PART 11/14 TOLL FREE:1-877-761-2819 ►www.tmgindustrial.com...
  • Page 13 STEP 8 : INSTALL FRONT AND REAR FABRIC PANELS. PART PART 12/14 TOLL FREE:1-877-761-2819 ►www.tmgindustrial.com...
  • Page 14 STEP 9 : INSTALL THE TOP COVER (#14) STRETCH AND TIGHTEN TOP COVER. Part Part 13/14 TOLL FREE:1-877-761-2819 ►www.tmgindustrial.com...

  • Page 15: After The Installation

    AFTER THE INSTALLATION Walk around and inspect the shelter periodically to make sure all components are still firmly secured and the whole shelter is well supported. Check all bolts and nuts as well as all connection points to make sure they are all in good position.

Table of Contents