Marmitek SC9000 Manual

Extending the SC9000 security console with a Digimax 210 thermostat.
The HF DigiMax 210 thermostat does not require extra wiring and has a radius of 30 m. The appliance is
equipped with a protected HF code. This code is registered with the SC9000 during installation. This code
ensures that the SC9000 will only respond to messages sent by your DigiMax 210. You can register up to
4 DigiMax 210 thermostats with the SC9000. Depending on the information sent out by the thermostat, the
SC9000 Marmitek X10 transmits ON and OFF signals via the mains, to switch the Marmitek X10 modules
connected to your boiler on or off. You can set a "differential temperature" in the SC9000, which lies
between 1 and 9 degrees. If the SC9000 is set to "Disarm" or "Arm Home", the X10 module connected to
your boiler will be switched on or off, depending on the comfort temperature set. If the SC9000 is set to
"Arm Away", the "differential temperature" setting will come in effect. Example: the room temperature is 15
°C, the comfort temperature set is 20 °C, with a "differential temperature" of 4 °C -> 20 °C – 4 °C = 16 °C:
this means the appliance will transmit a "turn on" command, until the temperature has reached 16 °C.
Registering a thermostat
1. To access the menu, press the menu
2. Enter your 4-digit PIN code (factory setting 0000.). For every digit, an asterisk (*) will appear on the
display.
3. If the PIN code has been entered correctly, the word INSTALL will appear on the display.
4. Press OK.
5. To register the thermostat with the console, keep both the + and – button of the thermostat pressed in
for 3 seconds. The DigiMax 210 will transmit the unique digital code every 10 seconds, during a period of
5 minutes. The display will flash and show the symbols
will read "STAT 1 OK".
Remove a registered thermostat
If you are using multiple thermostats, you can only remove all thermostats. Then you have to re-register
the thermostats you want to use.
1. To access the menu, press the menu
2. Enter your 4-digit PIN code (factory setting 0000.). For every digit, an asterisk (*) will appear on the
display.
3. If the PIN code has been entered correctly, the word INSTALL will appear on the display.
4. Press OK.
5. Use the buttons menu ↑/↓ to scroll to menu item 6: [MEMORY CLEAR] Press OK to select this item.
You can also go directly to item 6 by pressing the 6 on the keyboard.
6. Use the buttons menu ↑/↓ to scroll to menu item [CLEAR ALL THERMOSTATS] Press OK to select this
menu item.
7. The display will now read [CONFIRM CLR 1. YES 2. NO] Press 1 to confirm and erase the thermostats.
The thermostats have now been unregistered.
How does the console work with the Digimax 210?
The SC9000 transmits a X10 message on the unit code corresponding to the zone number of the console
and the house code of the console +3. In the factory setting, the house code of the console is set to A:
- thermostat in zone 1 will generate X10 messages on code B3,
- thermostat in zone 2 will generate X10 messages on code B4,
- thermostat in zone 3 will generate X10 messages on code B5,
- thermostat in zone 4 will generate X10 messages on code B6.
Example: You have set the house code for the console to B,
- thermostat in zone 1 will generate X10 messages on code C3,
- thermostat in zone 2 will generate X10 messages on code C4,
- thermostat in zone 3 will generate X10 messages on code C5,
- thermostat in zone 4 will generate X10 messages on code C6.
↑ or menu ↓ button. The display will now read
"[[[". The console will beep to confirm. The display
↑ or menu ↓ button. The display will now read [ENTER PIN]
- 1 -
[ENTER PIN]