1. Manuals
  2. Brands
  3. Outland Living Manuals
  4. Outdoor Fireplace
  5. SEYMOUR FMPPC2E-440
  6. Owner's manual

Outland Living SEYMOUR FMPPC2E-440 Owner's Manual

Fire table
Hide thumbs

Advertisement

Table of Contents

Model number FMPPC2E-440
® Registered trademark of FMI Brands Inc.
The OUTLAND Flame mark is a registered trademark of FMI Brands Inc.
MANUFACTURED BY FMI BRANDS INC. 101 – 3570 194 Street, Surrey, BC, Canada V3Z 1A5
USA, Canada Toll Free: 1-888-514-1663 | Email: info@outlandliving.com
Hours of Operation: 8:30AM - 4:00PM (Pacific Time)
OWNER'S MANUAL
SEYMOUR
FIRE TABLE
NOTICE : THIS
PRODUCT CONTAINS A
THERMOCOUPLE SAFETY
DEVICE WHICH SHUTS
OFF THE GAS. PLEASE
READ THE INSTRUCTIONS
CAREFULLY TO
UNDERSTAND HOW IT
WORKS.
D.440.000.V0

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SEYMOUR FMPPC2E-440 and is the answer not in the manual?

Questions and answers

Related Manuals for Outland Living SEYMOUR FMPPC2E-440

Summary of Contents for Outland Living SEYMOUR FMPPC2E-440

  • Page 1 OWNER’S MANUAL SEYMOUR FIRE TABLE NOTICE : THIS PRODUCT CONTAINS A THERMOCOUPLE SAFETY DEVICE WHICH SHUTS OFF THE GAS. PLEASE READ THE INSTRUCTIONS CAREFULLY TO UNDERSTAND HOW IT WORKS. Model number FMPPC2E-440 ® Registered trademark of FMI Brands Inc. The OUTLAND Flame mark is a registered trademark of FMI Brands Inc. D.440.000.V0 MANUFACTURED BY FMI BRANDS INC.

  • Page 2: Carbon Monoxide Hazard

    Installation and service must be performed by a CONSUMER: Retain this manual qualified installer, service agency, or the gas supplier. for future reference. En-1 OWNER & SAFETY MANUAL • OUTLAND LIVING • FIRE TABLE • SEYMOUR D.440.000.V0 ®...
  • Page 3 Indoor storage of this appliance is permissible only if the cylinder WARNING: is disconnected and removed from the appliance. Improper installation, adjustment, alteration, service or Cylinders must be stored outdoors in a well-ventilated area out maintenance can cause injury or property damage. Read of the reach of children.

  • Page 4: Gas Cylinder

    En-3 OWNER & SAFETY MANUAL • OUTLAND LIVING • FIRE TABLE • SEYMOUR D.440.000.V0 ®...
  • Page 5 LP gas supply must be shut off at the cylinder valve or the Only use a replacement hose by OUTLAND Living. cylinder must be removed from the appliance until the leak(s) is corrected.
  • Page 6 Middle Tabletop Tabletop Side Leaf Gusset Tabletop Support Beam Door Spreader Side Panel Front Panel Side Panel with Hinges Gas Valve Panel Top Back Panel En-5 OWNER & SAFETY MANUAL • OUTLAND LIVING • FIRE TABLE • SEYMOUR D.440.000.V0 ®...
  • Page 7 Supplied parts & hardware list: PART # DESCRIPTION QUANTITY PICTURE PART # DESCRIPTION QUANTITY PICTURE Wheel Hinged Door M4 x 12 Screw Tank Holder M5 x 16 Screw M5 Plain Washer Magnet M6 x 20 Screw (with integral split lock washers and flat washers) Adjustable Feet Required Tools (Not Supplied):...
  • Page 8 M5 x 6 Flat Head Screws Spacers Silicone Wind Fence Pad Pulse Igniter (Battery supplied separately) AA Battery CSA Hang Tags (English and French) 14 mm Open End Wrench En-7 OWNER & SAFETY MANUAL • OUTLAND LIVING • FIRE TABLE • SEYMOUR D.440.000.V0 ®...
  • Page 9 SECTION 1: ASSEMBLY STEP 1: DEFINE YOUR WORKING AREA MIDDLE TABLETOP (PART 1) Lay the Middle Tabletop on a level, soft, non- marking surface. STEP 2: BUILD THE TABLETOP ASSEMBLY 2.1 – Identify the (2) tabletop side leafs (part 2). 2.2 –...
  • Page 10 3.2 – Preinstall (4) M4x12 Screw (part 18) as indicated in the drawing. Do not tighten the screws. Leave at least 3 mm / 1/8” gap between the screw and the front panel. En-9 OWNER & SAFETY MANUAL • OUTLAND LIVING • FIRE TABLE • SEYMOUR D.440.000.V0 ®...
  • Page 11 SECTION 1: ASSEMBLY (continued) 3.3 – Install the side panel with hinges to the tabletop assembly with (4) M6 x 20 screws (with integral split lock washers and flat washers) (part 21). Tighten firmly. 3.4 – Identify (1) Side Panel (no hinges) (part 4) &...
  • Page 12 (part 21). Tighten firmly. 3.8 – Identify (4) Adjustable Feet (part 15). 3.9 – Install the adjustable feet to the bottom of the side panels. En-11 OWNER & SAFETY MANUAL • OUTLAND LIVING • FIRE TABLE • SEYMOUR D.440.000.V0 ®...
  • Page 13 SECTION 1: ASSEMBLY (continued) STEP 4: INSTALL THE PULSE IGNITER, GAS VALVE, GAS HOSE & REGULATOR ASSEMBLY TO THE GAS VALVE PANEL 4.1 – Fit the gas regulator and hose (part 16) through the gas valve panel (part 10) opening. Assemble the gas valve assembly to the front panel using (4) M4 x 12 screws (part 18).
  • Page 14 5.4 – Affix the gas valve panel to the tabletop using (3) M4 x 12 screws (part 18). 5.5 – Firmly fasten the (2) pre-installed screws on the side panel leg posts. En-13 OWNER & SAFETY MANUAL • OUTLAND LIVING • FIRE TABLE • SEYMOUR D.440.000.V0...
  • Page 15 SECTION 1: ASSEMBLY (continued) STEP 6: CONNECTING THE GAS VALVE TO THE BURNER 6.4 – Connect the igniter cable on the burner to the pulse igniter socket. Note the small rectangular connection. 6.1 – Identify 7/16”-20 UNF Flexible Hose on the gas valve & (1) Push in firmly.
  • Page 16 7.4 – Affix the top back panel to the tabletop using (3) M4 x 12 screws (part 18). 7.5 – Firmly fasten the (2) pre-installed screws on the side panel leg posts. En-15 OWNER & SAFETY MANUAL • OUTLAND LIVING • FIRE TABLE • SEYMOUR D.440.000.V0 ®...
  • Page 17 SECTION 1: ASSEMBLY (continued) STEP 9: INSTALL FRONT PANEL TO TABLETOP 9.1 – Identify (1) Front panel (part 9). 9.2 – Align the slots on the front panel with the pre-installed screws on the tabletop frame between the side panel posts. 9.3 –...
  • Page 18 (part 21). The gusset will be affixed to the leg post and tabletop leaf. 10.5 – Fully tighten all (6) screws once all fixings are installed on the gussets. En-17 OWNER & SAFETY MANUAL • OUTLAND LIVING • FIRE TABLE • SEYMOUR D.440.000.V0 ®...
  • Page 19 SECTION 1: ASSEMBLY (continued) STEP 10: ASSEMBLE LEG POSTS TO TABLETOP (CONTINUED) 10.6 – Complete the leg post assembly. Repeat steps 10.2.-10.5 to attach the (3) remaining leg posts. STEP 11 11.1 – Turn the fire table upright. Note: This is a two-person job. 11.2 –...
  • Page 20 (part 18). Leave at least 3 mm / 1/8” gap between the screw and the spreader bar. 12.4 – Lower the spreader bar so it rests on the floor. Fully tighten the (2) screws. En-19 OWNER & SAFETY MANUAL • OUTLAND LIVING • FIRE TABLE • SEYMOUR D.440.000.V0 ®...
  • Page 21 SECTION 1: ASSEMBLY (continued) STEP 13: ASSEMBLING THE PROPANE TANK TROLLEY 13.4 – Attach propane tank holder to the hinged door using (2) M6 x 20 screws (with integral split lock washers and flat 13.1 – Identify (1) Hinged Door (part 12), (1) Tank Holder (part 13), washers).
  • Page 22 14.2 – Align the female hinge on the door with the male hinge on the leg post. 14.3 – Carefully lower the door onto the hinges. PINCH POINT En-21 OWNER & SAFETY MANUAL • OUTLAND LIVING • FIRE TABLE • SEYMOUR D.440.000.V0 ®...
  • Page 23 SECTION 1: ASSEMBLY (continued) STEP 15: INSTALL SILICONE WIND FENCE PADS 15.1 – Identify (4) Silicone Wind Fence Pads (part 28). 15.2 – Insert the (1) silicone wind fence pad pins into the holes on the table slat that surrounds the end of the burner. PRESS THE SILCONE PAD SO IT BECOMES FLUSH WITH THE TABLE.
  • Page 24 Head Screws (part 26) - do not tighten screws. Once all 4 brackets are loosely assembled tighten the screws. Ensure the glass panels are straight and squarely aligned. En-23 OWNER & SAFETY MANUAL • OUTLAND LIVING • FIRE TABLE • SEYMOUR D.440.000.V0 ®...
  • Page 25 SECTION 1: ASSEMBLY (continued) STEP 16: ASSEMBLY OF THE GLASS WIND FENCE (CONTINUED) 16.3 – YOUR GLASS WIND BREAK IS NOW ASSEMBLED. Turn the glass wind break right side up so that the long end of the bracket is facing downwards. LOGO IS RIGHT SIDE UP LOGO IS...
  • Page 26 Align the Exterior Brackets with the inside edge of the rounded corners on the silicone pads. b. Slowly lower the glass wind break until it sits on the silicone pads. En-25 OWNER & SAFETY MANUAL • OUTLAND LIVING • FIRE TABLE • SEYMOUR D.440.000.V0 ®...
  • Page 27 SECTION 1: ASSEMBLY (continued) STEP 17: PROPANE CYLINDER ASSEMBLY Place an approved 20lb propane cylinder into the cylinder ring on the tank holder trolley. Couple the supplied gas regulator to the propane cylinder (see section labeled “Connection”). Perform LEAK TEST on all gas couplings (see section labeled “Leak Test”). Once all connections are verified to be secure, hand tighten the cylinder collar to affix cylinder.
  • Page 28 NOTE TO USER: Before igniting the unit for the first time, follow steps 1 through 6 in the below Ignition section. En-27 OWNER & SAFETY MANUAL • OUTLAND LIVING • FIRE TABLE • SEYMOUR D.440.000.V0 ®...
  • Page 29 SECTION 2: IGNITION STEP 1 Make sure no debris or flammable material is in or near the burn area. STEP 2 Ensure that the gas valve knob is in the “OFF” position by pushing and turning clockwise until the dial stops. STEP 3 Connect the LP gas cylinder.
  • Page 30 The thermocouple will automatically shut off the gas if the cable, or ground wire, is not connected properly. En-29 OWNER & SAFETY MANUAL • OUTLAND LIVING • FIRE TABLE • SEYMOUR D.440.000.V0 ®...
  • Page 31 SECTION 2: IGNITION (continued) WHAT IS A PULSE IGNITER? A pulse igniter is a device that generates electrical pulses used to create a spark to ignite a fuel-air mixture in a burner. When the spark is produced, it jumps across the spark gap and ignites the flammable gas, initiating combustion. TIPS: PULSE •...

  • Page 32: Ignition Troubleshooting

    ENSURE ALL CABLES ARE AND IGNITER TIP FIRMLY ATTACHED TO THE CORRECT SOCKETS MAKE SURE THE SILICONE COVERS ARE PRESSED UP AGAINST THE GAS VALVE CONNECTION En-31 OWNER & SAFETY MANUAL • OUTLAND LIVING • FIRE TABLE • SEYMOUR D.440.000.V0 ®...
  • Page 33 SECTION 3: TROUBLESHOOTING (continued) STEP 2 GOT A LOW FLAME? Wait until the burner assembly are cool, or wait 5 minutes for NOTE: Elevation and temperature affect the cylinder gas any gas to dissipate, whichever is longer. pressure and performance (flame height) of gas appliances. Your Turn the gas cylinder valve to the ‘Closed’...
  • Page 34 Let the fire in the burner extinguish, then turn the gas knob on the Fire Table to the ‘OFF’ position by pushing and turning the knob clockwise. STEP 3 Allow unit to cool for at least five (5) minutes before relighting. En-33 OWNER & SAFETY MANUAL • OUTLAND LIVING • FIRE TABLE • SEYMOUR D.440.000.V0 ®...
  • Page 35 SECTION 5: FIRE TABLE MAINTENANCE Your Outland Fire Table requires periodic maintenance to keep it in good running order. Follow the steps below to ensure your appliance will provide you with the best possible performance: Keep your Fire Table out of the rain and store it in a dry place. Fire Table accessories can be purchased at www.outlandliving.com or by calling 888-514-1663.

  • Page 36: Warning Notes

    • Never leave the Fire Table unattended while in operation. caution and stay away to avoid burns or clothing ignition. • Children should be supervised at all times when using this unit without exception. En-35 OWNER & SAFETY MANUAL • OUTLAND LIVING • FIRE TABLE • SEYMOUR D.440.000.V0 ®...
  • Page 37 REMOVING INSECT NESTS STEP 4 Using a wrench, remove the brass orifice adapter. WARNING: Small critters like spiders and earwigs can quickly build nests inside the burner tube which can obstruct gas flow and impact the flame height and heat performance of your appliance.

  • Page 38: Year Limited Warranty

    Any returns sent back to FMI Brands must be sent via prepaid freight and in the original retail packaging. Please register your OUTLAND Living product for proof of purchase and warranty at https://outlandliving.com/register-products/ For more warranty information and details please contact FMI Brands Inc. at info@outlandliving.com...

Table of Contents