Magtek DynaFlex Series Acceptance Inspection Manual page 2

Sides
The left and right sides are smooth plastic.
Quick Inspection
As part of your inspection, include the following for
your device inspection audit:
•
Be certain to have a list of the devices and
include the details listed on the product label.
•
It may be helpful to take photos of the front,
back, and side of each device.
Be certain to check device part numbers, serial
numbers and IDs and check physical connections. Use the chart below
as a checklist to inspect the device for signs of tampering.
Site Inspection
Form Factor - check overall form factor
Front
Signature Capture (optional - no stylus included)
Magnetic Stripe Swipe Path
LCD Display and Contactless Landing Zone
EMV Chip Card
Barcode reader
Sides
Magnetic Stripe Swipe Path
Rubberized Shell
Form Factor
Cables and charging cradle
USB-C cable
Underside and Back
Certificate Logos (imprinted)
Form Factor
Cable Connection
Pushbutton
Charging contacts
Labels
Tripped device
If there is forced entry, the security switches built
into the electronics will be tripped. If they are
tripped the sensitive data such as encryption keys
and certificates are cleared as part of security
measures mandated by PCI and the device will not
be available to make transactions.
NOTICE:
If the security switches have been tripped, DynaFlex / Pro cannot be
repaired in the field and must go back to the factory for repair. Follow
RMA procedures. User must report all signs of tampering as per stan-
dard protocol.
Inspection of Sides, Point of Installation, and Checklist Summary
Are there signs of tampering: Signs of tampering
YES
MagTek Inc., 1710 Apollo Court, Seal Beach CA 90740 | p 562-546-6400 | support 562-546-6800 | www.magtek.com
®
Compare the Hardware ID and Firmware ID:
https://www.pcisecuritystandards.org/assessors_and_solutions/pin_transaction_devices
FEATURES
Some features and functions may be documented, but not available with the current release of
NO
the product. Please contact your MagTek representative for questions about specific features
and functions and when they are scheduled to become available.
TRADEMARKS
EMV® is a registered trademark in the U.S. and other countries and an unregistered trademark
elsewhere. The EMV trademark is owned by EMVCo, LLC. The Contactless Indicator mark,
consisting of four graduating arcs, is a trademark owned by and used with permission of
EMVCo, LLC.
EU STATEMENT
Hereby, MagTek Inc. declares that the radio equipment types Wideband Transmission System
(Wireless LAN and Bluetooth Low Energy), and Non-Specific Short Range Device (contactless)
are in compliance with Directive 2014/53/EU. The full text of the EU declarations of conformity is
available at the following internet addresses:
• https://www.magtek.com/Content/DocumentationFiles/D998200404.pdf for DynaFlex with no
display, USB connection
• https://www.magtek.com/Content/DocumentationFiles/D998200411.pdf for DynaFlex Pro with
USB connection
UKCA STATEMENT
Hereby, MagTek Inc. declares that the radio equipment types Wideband Transmission System
(Wireless LAN and Bluetooth Low Energy), and Non-Specific Short Range Device (contactless)
are in compliance with Radio Equipment Regulations 2017 Directive S.I.2017:1206. The full text
of the UKCA declarations of conformity is available at the following internet addresses:
• https://www.magtek.com/Content/DocumentationFiles/D998200475.pdf for DynaFlex with no
display, USB connection
• https://www.magtek.com/Content/DocumentationFiles/D998200477.pdf for DynaFlex Pro with
USB connection
Certifications and Validation
PCI DEVICE VALIDATION
To check for PCI Validation check the
Hardware and Firmware ID. Hardware ID
is printed on the label.The Firmware ID is
accessible via the device and displayed on the
screen. Go to the PCI compliance web page
and search for MagTek, and find the product
name, DynaFlex.
MAGTEK: Registered to ISO 9001:2015 © Copyright 2024 MagTek, Inc. PN D998200359 rev. 100 10/24