Summary of Contents for Better Homes and Gardens Juliet Arch Dining Cabinet BHF336158813032
Page 1
LOT NUMBER: DATE PURCHASED: Juliet Arch Dining Cabinet Stock # BHF336158813032 # BHF336158813033 ADULT ASSEMBLY REQUIRED If you have any questions regarding assembly or if parts are missing, DO NOT return this item to the store where it was purchased. Please call our customer service number and have your instructions and parts list ready to provide the model name, part name or factory number: 1-866-942-5362 Pacific Standard Time: 8:30 a.m.
M A X I M U M R E C O M M E N D E D W E I G H T L O A D S MANUFACTURER: Whalen Furniture Manufacturing CATALOG : Juliet Arch Dining Cabinet MODEL # BHF336158813032 / BHF336158813033 MAXIMUM LOAD 22.7 kg / 50 lb.
Page 3
IMPORTANT Before you begin: Open, identify and count all parts prior to assembly. Lay out parts on a flat and non-abrasive surface. You will need the parts identified on page 4, 5 and 6 of this instruction manuals. NOTE: IT IS VERY IMPORTANT TO USE GLUE WITH DOWELS. EXCESS GLUE CAN BE WIPED OFF WITH DAMP CLOTH.
Page 4
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. A- Left Side Panel B- Right Side Panel (Qty. 1) (Qty. 1) C- Upper Fixed Shelf D- Lower Fixed Shelf (Qty.
Page 5
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. I- Bottom Side Frame J- Bottom Front / Back Stretcher (Qty. 2) (Qty. 2) K- Bottom Middle Stretcher L- Left Upper Door (Qty.
Page 6
Parts and Hardware List Please read completely through the instructions and verify that all listed parts and hardware are present before beginning assembly. (1) Cam Lock (2) Cam Bolt (3) M8 x 30 mm Wood Dowel (Qty. 30+1 extra) (Qty. 30+1 extra) (Qty.
Page 7
Assembly Instructions ② x 12 1. Unpack the unit and confirm that you have all the hardware and required parts listed. Assemble the unit on a carpeted floor or the empty carton to avoid any scratch. 2. Securely screw the Cam Bolts (2) into the designated small holes on the Side Panels (A and B). Tighten the cam bolts with a Phillips screwdriver.
Page 8
Assembly Instructions ② x 12 3. Securely screw the Cam Bolts (2) into the designated small holes on the Upper Fixed Shelf (C) and Bottom Panel (E) using a Phillips screwdriver.
Page 9
Assembly Instructions Magnet ④ x 4 ⑧ x 2 4. Using the pilot holes as a guide, orient and install 2 Magnetic Catches (8) to the Lower Fixed Shelf (D) with four 15 mm Washer Head Screws (4). NOTE: It is recommended to insert the screw through the CENTER of oval holes on both magnetic catches.
Page 10
Assembly Instructions ③ x 12 5. Glue the Wood Dowels (3) into the inner holes on the Fixed Shelves (C and D) and Bottom Panel (E). NOTE: It is very important to use a small amount of glue on both ends of dowels and wipe away the excess glue immediately with a damp cloth.
Page 11
Assembly Instructions The unfinished edges The finished edge and pilot holes for hinges are oriented at the same direction. ① x 2 6. Orient and attach the Upper Fixed Shelf (C) to the Left Side Panel (A) by engaging 2 Cam Locks (1). Turn the cam locks with a Phillips screwdriver until securely locked onto the cam bolts.
Page 12
Assembly Instructions The unfinished edge The cam lock housings face the floor when the unit is turned upright. ① x 2 7. Orient and attach the Lower Fixed Shelf (D) to the Left Side Panel (A) by engaging 2 Cam Locks (1). Turn the cam locks with a Phillips screwdriver until securely locked onto the cam bolts.
Page 13
Assembly Instructions Hinge mounting holes Cam locks face outward. ① x 2 The pilot holes face up. 8. Orient and attach the Bottom Panel (E) to the Left Side Panel (A) by engaging 2 Cam Locks (1).
Page 14
Assembly Instructions ① x 6 9. Repeat the previous process to attach the Right Side Panel (B) at the opposite end.
Page 15
Assembly Instructions ③ x 6 10. Glue six Wood Dowels (3) into the inner holes on both Arches (G and H).
Page 16
Assembly Instructions ⑨ x 2 11. Combine the assembled arches with the middle wood dowels fully inserted. 12. Insert two 45 mm Bolts (9) through the mounting holes on the Left Arch (G) and finger tighten into the Right Arch (H). DO NOT securely tighten the bolts.
Page 17
Assembly Instructions ① x 4 13. Orient and position the assembled arch onto both Side Panels (A and B) and tighten with 4 Cam Locks (1). 14. Go back and securely tighten the two 45 mm Bolts (9) installed in step 12 with the hex wrench provided.
Page 18
Assembly Instructions ② x 6 15. Securely screw the Cam Bolts (2) into the designated small holes on both Bottom Side Frames (I) using a Phillips screwdriver.
Page 19
Assembly Instructions ③ x 10 16. Glue 10 Wood Dowels (3) into the designated holes on the Bottom Stretchers (J and K) as shown.
Page 20
Assembly Instructions The cam lock housings facing inward. ① x 6 17. Orient and attach both Bottom Stretchers (J and K) to one Bottom Side Frame (I) with 3 Cam Locks (1). Turn the cam locks with a Phillips screwdriver until securely locked onto the cam bolts. Ask for assistance to hold each stretcher and ensure it is flush with the side frame before tightening cam locks.
Page 21
Assembly Instructions Try Square ① x 8 19. Align and attach the assembled base to the Bottom Panel (E) by engaging 8 Cam Locks (1). Turn the cam locks with a Phillips screwdriver until securely locked onto the cam bolts. 20.
Page 22
Assembly Instructions Upper right Upper left corner corner The adhesive tapes face outward. 1 mm ④ x 28 1 mm 21. Now, go back and securely tighten all the Cam Locks and Screws. Make sure that all the parts are tight and there are no gaps between them.
Page 23
Assembly Instructions Round hole ° Oval hole ⑤ x 32 25. Ask for assistance to turn over the unit at its back edge. 26. Using the pilot holes as a guide, align and attach one Hinge Base (O) onto the Left Side Panel (A). Insert two 15 mm Nickel Screws (5) through the CENTER of oval holes and move the hinge arm up or down to the desired position, then fasten the Hinge Base (O) into place.
Page 24
Assembly Instructions x 12 29. Ask for assistance to lift the assembled unit upright and position it near the final location. 30. Insert the Shelf Pins (11) into the holes at your desired height. Make sure you place the four Shelf Pins (11) at the same level to level the shelf.
Page 25
Assembly Instructions ⑥ x 4 ⑦ x 4 32. Fasten two Round Strike Plates (7) to each Upper Door (L and M) using two 15 mm Screws (6) in each.
Page 26
Assembly Instructions ⑩ x 8 33. Ask for assistance to lift the doors upright and attach one Handle (P) to the front side of each of the Doors (L, M and R) with two Handle Bolts (10).
Page 27
Assembly Instructions L/M/R ⑤ x 16 Depth Vertical Horizontal Adjustment Adjustment Adjustment 34. Ask for assistance to pick up the Left Upper Door (L) and fit it to the hinge cups installed on the upper portion of Left Side Panel (A). Loosely fasten one 15 mm Nickel Screw (5) through the UPPER hole of each hinge cup into the door frame.
Page 28
Assembly Instructions x 16 37. Insert the Cam Lock Covers (12) onto the visible cam locks to conceal the cams.
Page 29
Assembly Instructions IF YOU FIND THAT THE Floor DOORS ARE OUT OF ALIGNMENT, ADJUST leveler THE PRE-ATTACHED FLOOR LEVELERS TO CORRECT TILTING AND LEVEL THE DOORS. 38. The installed Magnetic Catches (8) can be adjusted to ensure that the doors function properly. This can be done by moving them forward and backward to the desired position.
Page 30
Assembly Instructions Wooden stud Nylon strap Wall Short screw Wall Metal bracket Long screw Tools required (not included): Phillips screwdriver, stud finder, tape measure, pencil, power drill and 1/8” drill bit. 39. Position the assembled unit at the desired location. Now, follow the instructions printed on the plastic bag containing the Tipping Restraint Hardware to attach the tip-over restraints to the unit and the wall.
Page 31
FURNITURE TIPPING RESTRAINT YOUNG CHILDREN MAY BE INJURED BY TIPPING FURNITURE AND YOU MUST USE THIS TIPPING RESTRAINT TO ATTACH THIS UNIT TO THE WALL, TO PREVENT ACCIDENTS AND/OR INJURIES. THIS HARDWARE, MUST BE PROPERLY INSTALLED (FOLLOW ALL DIRECTIONS IN ORDER ON THIS INSTRUCTIONS), TO PROVIDE PROTECTION AGAINST THE UNEXPECTED TIPPING OF FURNITURE DUE TO IMPROPER USE.
Care and Maintenance Use a soft, clean cloth that will not scratch the surface when dusting. Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area. Using solvents of any kind on your furniture may damage your furniture’s finish. ...
Page 33
NÚMERO de LOTE: FECHA de COMPRA: Gabinete arco para comedor Juliet Serie # BHF336158813032 # BHF336158813033 ENSAMBLE REQUERIDO POR ADULTO Si tienen alguna pregunta acerca del ensamble o si alguna parte está faltante, no retorne esté producto a la tienda donde lo compro. Por favor llame a nuestro departamento de ayuda al cliente teniendo su instructivo y lista de partes para proveer el modelo, nombre de parte o el número de fábrica: 1-866-942-5362 Hora estándar del Pacífico: 8:30 a.m.
Page 34
M Á X I M O P E S O R E C O M E N D A D O FABRICANTE: Whalen Furniture Manufacturing CATALOGO : Gabinete arco para comedor Juliet MODELO # BHF336158813032 / BHF336158813033 CARGA MÁXIMA 22.7 kg / 50 lb. ESTA UNIDAD DEBE UTILIZARSE DENTRO LOS PESOS MÁXIMOS INDICADOS.
Page 35
IMPORTANTE Antes de comenzar: Abra, identifique y cuente todas las partes antes del ensamble. Coloque las piezas sobre una superficie plana y no abrasiva. Tendrá las partes identificadas en la página 4, 5 y 6 de este manual de instrucciones. NOTA: ES MUY IMPORTANTE EL USO DE GOMA CON LAS CLAVIJAS DE MADERA.
Page 36
Lista de partes y material de ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes y partes de ferretería antes de iniciar el ensamblado. A- Panel izquierdo B- Panel derecho (Cant. 1) (Cant. 1) C- Repisa superior fija D- Repisa inferior fija (Cant.
Page 37
Lista de partes y material de ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes y partes de ferretería antes de iniciar el ensamblado. I- Marco inferior lateral J- Soporte inferior frontal / posterior (Cant. 2) (Cant.
Page 38
Lista de partes y material de ferretería Por favor lea completamente las instrucciones y verifique que estén todas las partes y partes de ferretería antes de iniciar el ensamblado. (1) Tuerca de fijación (2) Perno de fijación (3) Clavija de madera de M8 x 30 mm (Cant.
Page 39
Instructivo de ensamble ② x 12 1. Desempacar la unidad y confirmar que se tiene todo el material de ferretería y partes requeridas. Ensamblar la unidad en un piso alfombrado o en el cartón vacío para evitar rasguños. 2. Atornillar los pernos de fijación (2) en los agujeros pequeños designados en los paneles laterales (A y B).
Page 40
Instructivo de ensamble ② x 12 3. Atornillar los pernos de fijación (2) en los agujeros pequeños designados en la repisa superior fija (C) y el panel inferior (E) usando el desarmador estrella.
Page 41
Instructivo de ensamble Imán ④ x 4 ⑧ x 2 4. Usando los agujeros pilotos como guía, orientar e instalar 2 imanes (8) a la repisa inferior fija (D) con cuatro pernos de cabeza de arandela de 15 mm (4). NOTA: Se recomienda insertar el perno a través del CENTRO de los agujeros ovalados de ambos imanes.
Page 42
Instructivo de ensamble ③ x 12 5. Pegar las clavijas de madera (3) en los agujeros internos en las repisas fijas (C y D) y panel inferior (E). NOTA: Es importante usar una cantidad pequeña de pegamento en ambos lados de las clavijas y limpiar el exceso de pegamento inmediatamente con una toalla húmeda.
Page 43
Instructivo de ensamble Bordes sin acabado El borde con acabado y los agujeros pilotos para las bisagras están orientados en la misma dirección. ① x 2 6. Orientar y adjuntar la repisa superior fija (C) al panel izquierdo (A) empleando 2 tuercas de fijación (1). Girar las tuercas de fijación con el desarmador estrella hasta trabar seguramente sobre los pernos de fijación.
Page 44
Instructivo de ensamble Bordes sin acabado Los espacios de las tuercas de fijación apuntarán al piso cuando la unidad esté en posición vertical. ① x 2 7. Orientar y adjuntar la repisa fija inferior (D) al panel izquierdo (A) empleando 2 tuercas de fijación (1). Girar las tuercas de fijación con el desarmador estrella hasta trabar sobre los pernos de fijación.
Page 45
Instructivo de ensamble Agujeros de montaje de las bisagras Las tuercas de fijación apuntan hacia afuera. ① x 2 Los agujeros pilotos quedan hacia arriba. 8. Orientar y adjuntar el panel inferior (E) al panel izquierdo (A) empleando 2 tuercas de fijación (1).
Page 46
Instructivo de ensamble ① x 6 9. Repetir los procesos previos para adjuntar el panel derecho (B) al extremo opuesto.
Page 47
Instructivo de ensamble ③ x 6 10. Pegar seis clavijas de madera (3) en los agujeros internos en ambos arcos (G y H).
Page 48
Instructivo de ensamble ⑨ x 2 11. Combinar los arcos ensamblados con las clavijas de madera medias insertadas completamente. 12. Insertar 2 pernos de 45 mm (9) a través de los agujeros de montaje en el arco izquierdo (G) y apriételos con los dedos en el arco derecho (H).
Page 49
Instructivo de ensamble ① x 4 13. Orientar y poner el arco ensamblado sobre ambos paneles laterales (A y B) y apretar con 4 tuercas de fijación (1). 14. Vuelva atrás y apriete firmemente los dos pernos de 45 mm (9) instalados en el paso 12 con la llave hexagonal proporcionado.
Page 50
Instructivo de ensamble ② x 6 15. Atornillar a los pernos de fijación (2) en los agujeros pequeños designados en ambos marcos inferiores laterales (I) usando los desarmadores estrella.
Page 51
Instructivo de ensamble ③ x 10 16. Pegar 10 clavijas de madera (3) en los agujeros designados en los soportes inferiores (J y K), como se muestra...
Page 52
Instructivo de ensamble Los espacios de las tuercas de fijación apuntan hacia adentro ① x 6 17. Orientar y adjuntar ambos soportes inferiores (J y K) a un marco inferior lateral (I) con 3 tuercas de fijación (1). Girar las tuercas de fijación con el desarmador estrella y trabar sobre los pernos de fijación. Pedir asistencia para sostener cada soporte y asegurar que esté...
Page 53
Instructivo de ensamble Escuadra ① x 8 19. Alinear y adjuntar la base ensamblada al panel inferior (E) empleando 8 tuercas de fijación (1). Girar las tuercas de fijación con el desarmador estrella hasta trabar sobre los pernos de fijación. 20.
Page 54
Instructivo de ensamble Esquina superior Esquina superior izquierda derecha Las cintas adhesivas apuntan hacia afuera. 1 mm ④ x 28 1 mm 21. Ahora, volver y apretar todas las tuercas de fijación y los pernos. Asegurar que todas las partes estén apretadas y de que no hay huecos entre las partes.
Page 55
Instructivo de ensamble Agujero redondo ° Agujero ovalado ⑤ x 32 25. Pedir asistencia para poner la unidad sobre su borde posterior. 26. Usando los agujeros pilotos como guía, alinear y adjuntar una base de bisagra (O) sobre el panel izquierdo (A).
Page 56
Instructivo de ensamble x 12 29. Pedir asistencia para levantar la unidad ensamblada en posición vertical y cerca del lugar final. 30. Insertar los soportes para repisa (11) en los agujeros a su altura deseada. Asegurar de poner cuatro soportes para repisa (11) al mismo nivel para nivelar la repisa. 31.
Page 57
Instructivo de ensamble ⑥ x 4 ⑦ x 4 32. Sujetar 2 placas redondas (7) a cada puerta superior (L y M) usando 2 pernos de 15 mm (6) en cada uno.
Page 58
Instructivo de ensamble ⑩ x 8 33. Pedir asistencia para levantar las puertas en posición vertical y adjuntar una manija (P) al lado frontal de cada una de las puertas (L, M y R) con 2 pernos para manija (10).
Page 59
Instructivo de ensamble L/M/R ⑤ x 16 Ajuste de Ajuste Ajuste profundida vertical horizontal 34. Pedir asistencia para tomar la puerta izquierda superior (L) y encajar en las copas de bisagra instaladas en la porción superior del panel izquierdo (A). Sujetar flojamente un perno de níquel de 15 mm (5) a través del agujero SUPERIOR de cada copa de bisagra en el marco de la puerta.
Page 60
Instructivo de ensamble x 16 37. Insertar las tapas de las tuercas de fijación (12) sobre las tuercas de fijación visibles para esconder.
Page 61
Instructivo de ensamble SI ENCUENTRA QUE LAS Nivelador PUERTAS ESTÁN FUERA DE ALINEACIÓN, de piso AJUSTAR LOS NIVELADORES DE PISO PRE- ADJUNTADOS PARA CORREGIR LA INCLINACIÓN Y NIVELAR LAS PUERTAS. 38. Los imanes (8) instalados se pueden ajustar para asegurar que las puertas funcionen apropiadamente. Esto se puede hacer moviéndolos hacia enfrente y hacia atrás a la posición deseada.
Page 62
Instructivo de ensamble Viga de madera Correa de Nylon Pared Perno corto Pared Soporte de Perno largo metal Herramientas requeridas (no incluidas): Desarmador estrella, buscador de vigas, cinta métrica, lápiz, taladro y broca de 1/8 pulgadas. 39. Pedir asistencia para poner la unidad ensamblada en el lugar deseado. Ahora, siga las instrucciones imprimidas en la bolsa de plástico que contiene el juego de restricción de movimiento para adjuntar los topes de movimientos a la unidad y pared.
Page 63
SISTEMA DE RESTRICCIÓN DE MOVIMIENTO NIÑOS PEQUEÑOS PUEDEN RESULTAR LASTIMADOS POR MUEBLES INCLINADOS Y DEBE INSTALAR EL JUEGO DE RESTRICCIÓN DE MOVIMIENTO CON LA UNIDAD EN FUNCIÓN, PARA PREVENIR LA INCLINACIÓN DE LA UNIDAD, CAUSANDO CUALQUIER ACCIDENTE O DAÑO. ESTÉ JUEGO DEBE SE INSTALADO CORRECTAMENTE (SIGA LAS DIRECCIÓN EN ORDEN DE LAS INSTRUCCIONES), PARA PROVEER PROTECCIÓN EN CONTRA DE LA INCLINACIÓN INESPERADA DEL MUEBLE DEBIDO AL USO INAPROPIADO.
Page 64
Mantenimiento y cuidados Use una toalla suave y limpia para evitar daños y rayaduras. Uso de cera para pulir muebles no es necesario. Si desea usar cera, pruébela en un área que no sea visible para revisar su funcionamiento. ...
Need help?
Do you have a question about the Juliet Arch Dining Cabinet BHF336158813032 and is the answer not in the manual?
Questions and answers