Page 2
SERIAL NUMBER For your future reference, mark the serial number in the space provided. Haag-Streit USA Inc. QUALITY MANAGEMENT 3535 Kings Mills Road SYSTEM Mason, Ohio 45040-2303 REGISTERED TO ISO 13485:2016 1-800-787-5426 MADE IN USA www.haag-streit-usa.com IN-TABLETOP...
Table of Contents IMPORTANT INFORMATION........4 A. Safety Symbols Defi nitions......4 B. Transportation and Storage Conditions....4 TECHNICAL SPECIFICATIONS........4 1. INTRODUCTION...........5 2. INSTALLATION FOR TABLETOP W/RHEOSTAT (320210, 320230)..........6 Unpacking ............6 Attaching the Blank ........6 2.3 Attaching the Power Supply.......6 Attaching the Power Cord .......6...
SUIVIES CORRECTEMENT, POURRAIENT This equipment is rated Class I CAUSER UNE PERTE DE VIE OU UNE BLESSURE. Equipment Model Ergonomic Tabletop 320210 “WARNING” : THE WARNING SYMBOL Class I IDENTIFIES SPECIAL INSTRUCTIONS OR PROCEDURES WHICH, IF NOT CORRECTLY FOLLOWED, COULD RESULT IN PERSONAL INJURY.
1.1. This Installation and Operating Instruction contains OR DAMAGE TO THE EQUIPMENT, ONLY information applicable only to the Reliance® Ergonomic AUTHORIZED RELIANCE® DISTRIBUTORS Tabletop Models 320210, 320220, 320230, 320240. SHOULD INSTALL OR MOVE THE EQUIPMENT. 1.2. Should your product not perform properly, or if AVERTISSEMENT : POUR ÉVITER UNE...
(See Figure 2) Locate the FOR TABLETOP W/RHEOSTAT Rheostat Blank Cover that is also supplied, peel the adhesive (320210, 320230) protection from the back of the Blank Cover and attach it to the other cutout on the opposite side of the Ergonomic 2.1.
Page 7
Bottom Blank Plate Serial Number label Power Supply Use these holes to help route cables. Use cable ties to help route cables. TIP: Add cable ties before attaching the Power Supply. FIGURE 2 Bottom View of Tabletop After Installation (Shown w/ Power Supply on Left) IN-TABLETOP...
Rheostat Blank Cover Power Supply Cover not on ON/OFF Switch older units 5-15P end of Power Cord Slit Lamp Arm (Part of the 7900 Instrument Stand) FIGURE 3 Top View Of Ergonomic Tabletop (Shown Installed on Slit Lamp Arm) (Shown w/ Power Supply on Left & Rheostat on Right) IN-TABLETOP...
3. INSTALLATION FOR TABLETOP FOR IMAGING (320220, 320240) Remove all external shipping tapes and wrappings. Remove the Ergonomic Tabletop from the carton. 3.2 Place the Ergonomic Tabletop onto the Slit lamp Arm on the 7900 Instrument Stand. (See Figure 3) 4.
Note: Equipment should be cleaned as needed Note: For repair, contact the Technical Service or per local or healthcare profession guidelines. Department, Haag-Streit USA, 3535 Kings Mills Road, Mason, Ohio 45040-2303, or call (800) REMARQUE : L’équipement devrait être 787-5426.
Should your ErgonomicTabletop not perform properly, or if replacement parts are needed, contact the Haag-Streit Distributor, where you purchased this product or contact the Technical Service Department, Haag-Streit USA, Inc., 3535 Kings Mills Road, Mason, Ohio 45040- 2303, or call (800) 787-5426. IN-TABLETOP...
MODEL ERGONOMIC TABLETOP ASSEMBLY W/RHEOSTAT (Shown w/ Power Supply on Left & Rheostat on Right) To order complete Ergonomic Tabletop Assembly use P/N’s. 320210 - BI/BM Ergonomic Tabletop Assembly - w/Rheostat 320230 - BP/BQ Ergonomic Tabletop Assembly - w/Rheostat IN-TABLETOP...
Haag-Streit dealer and is subject to the following conditions: 1. The warranty card must be completed and returned to Haag-Streit USA, Inc. within two (2) weeks from the date of installation.
Need help?
Do you have a question about the 320210 and is the answer not in the manual?
Questions and answers