Advertisement
Quick Links
www.ti.com
User's Guide
AM243x LaunchPad™ Development Kit User's Guide
The AM243x LaunchPad
the Texas Intruments Sitara
start developing on the AM243x MCUs with on-board emulation for programming and debugging as well as
buttons and LEDs for a simple user interface. The LaunchPad also features two independent BoosterPack XL
expansion connectors, on-board Controller Area Network (CAN) transciever, two RJ45 Ethernet ports, and an
on-board XDS110 debug probe.
First.........................................................................................................................................................3
1.1 If You Need Assistance......................................................................................................................................................
1.2 Important Usage Notes......................................................................................................................................................
2 Kit Overview............................................................................................................................................................................
Contents........................................................................................................................................................................5
Features......................................................................................................................................................................5
2.3 Component Identification...................................................................................................................................................
2.4 BoosterPacks.....................................................................................................................................................................
2.5 Compliance........................................................................................................................................................................
Setup.............................................................................................................................................................................7
Requirements..........................................................................................................................................................7
3.1.3 Power Tree................................................................................................................................................................
Sequence........................................................................................................................................................11
3.2 Push Buttons....................................................................................................................................................................
3.3 Boot Mode Selection........................................................................................................................................................
Description...........................................................................................................................................................13
4.1 Functional Block Diagram................................................................................................................................................
4.2 BoosterPack Headers......................................................................................................................................................
4.2.1 Pinmux for BoosterPack............................................................................................................................................
4.3 GPIO Mapping.................................................................................................................................................................
4.4
Reset................................................................................................................................................................................27
4.5 Clock................................................................................................................................................................................
4.6 Memory Interface.............................................................................................................................................................
4.6.1 QSPI Interface...........................................................................................................................................................
EEPROM....................................................................................................................................................30
Interface.............................................................................................................................................................31
4.7.1 Ethernet PHY Strapping............................................................................................................................................
4.7.3 LED indication in Ethernet RJ45 Connector..............................................................................................................
Interface.............................................................................................................................................................35
Interface.....................................................................................................................................................................35
4.10 Industrial Application LEDs............................................................................................................................................
Interface...............................................................................................................................................................37
Interface...............................................................................................................................................................38
Interface.................................................................................................................................................................40
Interface...................................................................................................................................................................41
4.15 JTAG Emulation.............................................................................................................................................................
4.16 Test Automation Interface..............................................................................................................................................
4.17 SPI Interface..................................................................................................................................................................
SPRUJ12A - AUGUST 2021 - REVISED NOVEMBER 2021
Submit Document Feedback
™
development kit is a simple and inexpensive hardware evaluation module (EVM) for
™
AM243x series of microcontrollers (MCUs). This EVM provides an easy way to
Table of Contents
Connector.................................................................................................................7
....................................................................................................................................................9
Interrupt..........................................................................................................34
Copyright © 2021 Texas Instruments Incorporated
ABSTRACT
AM243x LaunchPad™ Development Kit User's Guide
Table of Contents
3
3
4
6
7
7
10
11
12
13
14
16
25
28
29
29
32
34
36
43
44
46
1
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Texas Instruments LaunchPad AM243 Series
Summary of Contents for Texas Instruments LaunchPad AM243 Series
-
Page 1: Table Of Contents
Interface................................38 4.13 CAN Interface.................................40 4.14 FSI Interface...................................41 4.15 JTAG Emulation................................4.16 Test Automation Interface.............................. 4.17 SPI Interface.................................. SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... - Page 2 Table 4-9. Net Name in Schematic and Package Signal Name for J6/J8 Connector..............Table 4-10. GPIO Mapping Table...............................25 Table 4-11. Clock Frequency Table............................28 AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
-
Page 3: Preface: Read This First
(only allowing data transfer from side B to A). The signals that not able to propagate to the BoosterPack headers include: UART2_RTSn, EHRPWM2_A, EHRPWM2_B, as well as any GPIO signals on the listed pins. SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 4: Kit Overview
Kit Overview www.ti.com 2 Kit Overview Figure 2-1. AM243x LaunchPad Board AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 5: Kit Contents
Four push buttons: – PORz Reset – MCU warm reset – SoC warm reset – User interrupt SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 6: Component Identification
2.3 Component Identification Figure 2-3. AM243x LaunchPad Top Component Identification Figure 2-4. AM243x LaunchPad Bottom Component Identification AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 7: Boosterpacks
AM243x LaunchPad. You can also build your own BoosterPack by following the design guidelines on TI’s website. Texas Instruments even helps you promote your BoosterPack to other members of the community. TI offers a variety of avenues for you to reach potential customers with your solutions. -
Page 8: Figure 3-1. Type-C Cc Configuration
Two DC-DC buck regulators (TPS62822) are used to generate the 3.3 V main supply and VDD_CORE_0V85 from the 5 V input supply. AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 9: Power Status Led's
Power indicator for voltage - VDD_CORE_0V85 LD11 XDS110_PROG_STAZ1 LED will glow after XDS configuration LD10 XDS110_PROG_STAZ2 Figure 3-3. Power Status LED's SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 10: Power Tree
Board Setup www.ti.com 3.1.3 Power Tree Figure 3-4. Power Tree Diagram of AM243x LaunchPad AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 11: Power Sequence
PORz Reset input MCU_RESETz MCU warm reset input SoC_RESET_REQz SoC warm reset input USER_INTn User interrupt input SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 12: Boot Mode Selection
USB -DFU No Boot Figure 3-6. Boot-Mode DIP Switch Note SW4.8 of the DIP switch remains unused. AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 13: Hardware Description
Hardware Description 4 Hardware Description 4.1 Functional Block Diagram Figure 4-1. AM243x LaunchPad Functional Block Diagram SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 14: Boosterpack Headers
MMC1 • ADC0 • EHRPWM0_A/B and EHRPWM1_A/B • GPIO's • 5 V and 3.3 V power supplies AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 15: Figure 4-3. Site #2 Boosterpack Header
Power to BoosterPack sourced from LaunchPad ✔ Power to BoosterPack sourced from the BoosterPack Figure 4-3. Site #2 BoosterPack Header SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 16: Pinmux For Boosterpack
Hardware Description www.ti.com 4.2.1 Pinmux for BoosterPack Figure 4-4. 80 Pin BoosterPack Pinout AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 17: Table 4-2. Pinmux Options For J1/J3 Connector - Site 1
J1.10 I2C1_SDA CPTS0_HW2TSPU TIMER_IO1 SPI2_CS2 DDR0_IO_PLL_REFCLK_TES DDR0_IO_PLL_REFCLK_TES GPIO1_6 J3.30 MCAN0_RX UART4_TXD TIMER_IO3 SYNC3_OUT SPI4_CS2 GPIO1_6 EQEP2_S UART0_RIn SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 18: Table 4-3. Net Name In Schematic And Package Signal Name For J1/J3 Connector
GPIO1_18 PRG0_PRU0_GPO18 J3.28 BP_ADC0_AIN7 ADC0_AIN7 J1.9 SOC_I2C1_SCL I2C1_SCL J3.29 SYNC2_OUT MCAN0_TX J1.10 SOC_I2C1_SDA I2C1_SDA J3.30 SYNC3_OUT MCAN0_RX AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 19: Table 4-4. Pinmux Options For J2/J4 Connector - Site 1
PRG0_PRU0_G PRG0_PRU0_G PRG0_PRU0_G PRG0_RGMII1_ PRG0_PWM2_ GPIO1_2 GPMC0_A0 UART2_RTSn J2.11 GPIO1_20 PRG0_PRU1_G PRG0_PRU1_G PRG0_PRU1_G PRG0_RGMII2_ GPIO1_20 EQEP0_A UART5_CTSn SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 20: Table 4-5. Net Name In Schematic And Package Signal Name For J2/J4 Connector
GPIO1_0 PRG0_PRU0_GPO0 J2.13 GPIO1_5 PRG0_PRU0_GPO5 J4.32 GPIO1_1 PRG0_PRU0_GPO1 J2.12 SPI3_CS1 PRG0_PRU0_GPO15 J4.31 GPIO1_2 PRG0_PRU0_GPO2 J2.11 GPIO1_20 PRG0_PRU1_GPO0 AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 21: Table 4-6. Pinmux Options For J5/J7 Connector - Site 2
PRG0_PRU1_GPO6 PRG0_PRU1_GPI6 PRG0_RGMII2_RXC GPIO1_26 EQEP2_A GPMC0_A19 UART4_CTS J5.50 I2C0_SDA UART6_RTSn GPIO1_65 J7.70 PRG0_PRU1_GPO1 PRG0_PRU1_GPI1 PRG0_RGMII2_TD0 GPIO1_31 EQEP2_I UART4_RXD SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 22: Table 4-7. Net Name In Schematic And Package Signal Name For J5/J7 Connector
GPIO1_6 PRG0_PRU0_GPO6 J7.68 GPIO1_22 PRG0_PRU1_GPO2 J5.49 SOC_I2C0_SCL_BP I2C0_SCL J7.69 GPIO1_26 PRG0_PRU1_GPO6 J5.50 SOC_I2C0_SDA_BP I2C0_SDA J7.70 GPIO1_31 PRG0_PRU1_GPO11 AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 23: Table 4-8. Pinmux Options For J6/J8 Connector - Site 2
GPMC0_A1 J8.71 PRG0_PRU1_GPO PRG0_PRU1_GPI13 PRG0_RGMII2_TD2 PRG0_PWM1_B GPIO1_3 EQEP0_I GPMC0_A8 UART5_RXD J6.51 PRG0_PRU0_GPO PRG0_PRU0_GPI8 PRG0_PWM2_A1 GPIO1_8 GPMC0_A2 UART4_RTSn SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 24: Table 4-9. Net Name In Schematic And Package Signal Name For J6/J8 Connector
GPIO1_78 MMC1_SDWP J6.53 GPIO1_40 PRG0_MDIO0_MDIO J8.72 GPIO1_32 PRG0_PRU1_GPO12 J6.52 GPIO1_41 PRG0_MDIO0_MDC J8.71 GPIO1_33 PRG0_PRU1_GPO13 J6.51 GPIO1_8 PRG0_PRU0_GPO8 AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 25: Gpio Mapping
Interrupt signal from both RGMII1 & RGMII2 Ethernet PHY's GPIO0_50 PRG1_PRU0_GPO5 GPIO0_50 GPIO connected to BoosterPack header SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... - Page 26 Default State Function VPP_1V8_REG_EN PRG1_PRU0_GPO8 GPIO0_53 Output Active High To enable the VPP Regulator for eFUSE Programming AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated...
-
Page 27: Reset
Upon Power on Reset, all peripheral devices connected to MCU domain get reset by MCU_RESETSTATz. One User input interrupt is connected to one of the GPIO of SoC. SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 28: Clock
The 16 MHz clock will only become active after power is supplied to the micro-B USB connector after insertion of a cable into the micro-B USB port. AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 29: Memory Interface
VCCQ pins of the flash memory. The OSPI0 interface of the SoC is powered by the VDDSHV_3V3 supply. Figure 4-7. QSPI Interface SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 30: Board Id Eeprom
VendorID 0028 CHAR 1 is Mistral Build_Week 002A CHAR Filled in by Mistral Build_Year 002C CHAR 2021 AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 31: Ethernet Interface
The LaunchPad supports two Ethernet PHYs that are terminated to RJ45 connectors with integrated magnetics for external communication. Figure 4-9. Ethernet Connection SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 32: Ethernet Phy Strapping
Both PHY modes are selected as RGMII to copper with auto-negotiation advertised for 1000 Base-T, 100 Base-Tx, and 10 Base-Te speeds. AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 33: Figure 4-11. Ethernet Phy Strapping For Rgmii1 Phy
4-12. Figure 4-11. Ethernet PHY Strapping for RGMII1 PHY Figure 4-12. Ethernet PHY Strapping for RGMII2 PHY SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 34: Ethernet Phy - Power, Clock, Reset, Interrupt
LED1 is connected to RJ45 LED (orange) to indicated 1000 MHz link or receive error. • LED2 is connected to RJ45 LED (green) to indicate transmit/receive activity. AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 35: Usb 2.0 Interface
– Test automation header (687140183622 from Wurth) – I2C1 is also connected to the BoosterPack (J1.9, J1.10) expansion connector Figure 4-14. I2C Interface SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 36: Industrial Application Leds
The other green LED, as well as the red and two bi-color LEDs, are connected to SoC GPIO's such that they can be toggled based on the application. Figure 4-15. Industrial Application LEDs AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 37: Uart Interface
One UART port from the main domain of the SoC (Main_UART0) is connected to a buffer (SN74AVC4T245PW) isolated between the SoC and the on-board emulator XDS110 (TM4C1294NCPDTT3R) Figure 4-16. UART Interface SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 38: Eqep Interface
(B13). Mux channel selection is done using SoC GPIO. Figure 4-17. eQEP Interface Figure 4-18. eQEP1 Header AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 39: Figure 4-19. Eqep2 Header
Hardware Description Figure 4-19. eQEP2 Header Figure 4-20. eQEP2 or MCAN0 Mux Selection Circuit SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 40: Can Interface
CAN transceiver’s high and low are connected to the 3-pin header (J11). Figure 4-21. CAN Interface Figure 4-22. MCAN Transceiver and Header AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 41: Fsi Interface
J16.2 FSI_TX0_CLK J16.3 J16.4 J16.5 FSI_RX0_D0 J16.6 FSI_TX0_D0 J16.7 FSI_RX0_D1 J16.8 FSI_TX0_D1 J16.9 No connection J16.10 VSYS_3V3 SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 42: Figure 4-24. Fsi Header
Hardware Description www.ti.com Figure 4-24. FSI Header Figure 4-25. FSI or BoosterPack Mux Selection Circuit AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 43: Jtag Emulation
IEC 61000-4-2. Figure 4-26. JTAG Interface Figure 4-27. Micro-B USB Connection for JTAG SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 44: Test Automation Interface
AM243x. Boot mode for the AM243x can be controlled by either the DIP switch or the test automation header through the I2C IO expander. AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 45: Table 4-16. Test Automation Header Pinout
Data signal for SoC I2C Bidirectional BOOTMODE_I2C_SDA Data signal for I2C IO expander for boot mode Ground DGND Ground DGND SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 46: Spi Interface
The SPI connections between the SoC and the BoosterPack connectors are show in Figure 4-29. Figure 4-29. SPI Connection From SoC to BoosterPack Connector AM243x LaunchPad™ Development Kit User's Guide SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... -
Page 47: Reference Documents
• Altered description of BoosterPack to not include recommendation of sourcing power to LP from BoosterPack ..................................14 SPRUJ12A – AUGUST 2021 – REVISED NOVEMBER 2021 AM243x LaunchPad™ Development Kit User's Guide Submit Document Feedback Copyright © 2021 Texas Instruments Incorporated... - Page 48 STANDARD TERMS FOR EVALUATION MODULES Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, and/or documentation which may be provided together or separately (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms set forth herein.
- Page 49 www.ti.com Regulatory Notices: 3.1 United States 3.1.1 Notice applicable to EVMs not FCC-Approved: FCC NOTICE: This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit to determine whether to incorporate such items in a finished product and software developers to write software applications for use with the end product.
- Page 50 www.ti.com Concernant les EVMs avec antennes détachables Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à...
- Page 51 www.ti.com EVM Use Restrictions and Warnings: 4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS. 4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling or using the EVM, including without limitation any warning or restriction notices.
- Page 52 Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief in any United States or foreign court. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2019, Texas Instruments Incorporated...
- Page 53 TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for TI products. TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2022, Texas Instruments Incorporated...
Need help?
Do you have a question about the LaunchPad AM243 Series and is the answer not in the manual?
Questions and answers