WEG W30 Smart EC Installation, Operation And Maintenance Manual
Frame iec 132 / nema 210 three-phase motors
Hide thumbs
Also See for W30 Smart EC:
- Quick manual (6 pages) ,
- Installation, operation and maintenance manual (32 pages) ,
- Installation, operation and maintenance manual (28 pages)
Subscribe to Our Youtube Channel
Related Manuals for WEG W30 Smart EC
Summary of Contents for WEG W30 Smart EC
- Page 1 W30 Smart EC frame IEC 132 / NEMA 210 Three-Phase Motors Installation, Operation and Maintenance Manual...
- Page 2 Failure to follow the instructions in this manual and on the website www.weg.net voids the product warranty and may result in serious personal injury and material damage. For further information or explanations, check our FAQ at www.weg.net/br/faq.
-
Page 3: Table Of Contents
7.2. Information for Contacting Technical Support ............14 8. Maintenance ......................14 9. Environmental Information ..................14 10. Additional Information ..................14 10.1. Warranty Term ......................14 11. Technical Specifications ..................15 11.1. Power Supply .......................15 11.2. Ventilation System ....................15 11.3. Standards and Directives ..................15 W30 Smart EC | 3... -
Page 4: General Information
1. General Information The W30 Smart EC product is an Electronically Commutated (EC) Motor, consisting of a permanent magnet motor and a drive with features customized for ventilation solutions. This Manual contains only the required information that allows qualified and trained personnel to carry out their services. -
Page 5: Identification Labels
4. Identification Labels There is one nameplate with general product information on the W30 Smart EC product that is affixed to the side of the motor frame and one label with basic electronic information that is affixed to the drive (back cover). - Page 6 For flying leads motors, do not push the overlength of leads into the motor in order to prevent that they touch the rotor. Drain hole: W30 Smart EC product can be supplied with drains. Figure 4 and Figure 5 give details about the mounting configuration.
-
Page 7: Power Connections
If used, connect the optional external harmonic filter (passive PFC) in series to the line conductor. WEG declares that the W30 Smart EC motor line is intended to be used as a part of an end-product and thus is not an independently used machine. -
Page 8: Xc10 Connector
Name Description Number Figure 10 - XC10 control connections. DO1-RL-NC Digital Output 1: Relay 1 Normally Closed Contact DO1-RL-C Digital Output 1: Relay 1 Common Contact DO1-RL-NO Digital Output 1: Relay 1 Normally Open Contact 8 | W30 Smart EC... -
Page 9: Emc Requirements For Conforming Installations
For optional decentralized mounting, the product class may change and the product may require the use of external filters. Consult WEG for the solution that better comply with your installation requirements. W30 Smart EC product may require the use of an external filter to comply with harmonic current emissions requirements (EN61000-3-2). Consult WEG about optional external filters. -
Page 10: Product Standard Features And Control Reference
The built-in power supplies have an output limit of 10 V source: 50 mA max W30 Smart EC motors may be permanently damaged if subjected to signals outside of the specified range. Make sure that all unused conductors in control cable are insulated to avoid product malfunction or damage. -
Page 11: Fire Mode Function (Optional)
WEG strongly recommends following the precautions and procedures outlined above before using the W30 Smart EC in ‘Fire Mode.’ WEG will not be liable to the end user or third parties for any direct or indirect losses or damages resulting from the programming and operation of the W30 Smart EC in ‘Fire Mode,’... -
Page 12: Serial Communication
All devices on the network must be properly grounded, preferably to the same ground connection. The cable shielding should also be grounded. Enable the termination resistors only at two points, at the ends of the main bus, even if there are branches from the bus. 12 | W30 Smart EC... -
Page 13: Interfaces To Access Parameters
Note: Do not connect any other device to the XC13 connector, it may damage the device. Do not use the HMI simultaneously with other devices connected to the XC14 connector. 6.6.1.3. Bluetooth Connect a Bluetooth module (Material 16047097) to the XC3 connector and use the WPS app downloaded through the appstores (Android/IOS) to connect. W30 Smart EC | 13... -
Page 14: Product Protection And Fault Diagnosis
Output overcurrent / short-circuit protection (F070); W30 Smart EC has a LED in the middle of its frame cover, which indicates the fault status and helping in the fault diagnosis: The LED will stay ON while the motor is running (speed higher than zero);... -
Page 15: Technical Specifications
WEG, will not be covered by the warranty.The warranty will not apply if the customer at its own discretion makes repairs and/or modifications to the equipment without prior written consent from WEG. -
Page 16: Eu Declaration Of Conformity
No.2226, South Second Ring East Road, Jintan District, Changzhou City, Jiangsu Province, China. www.weg.net/cn declares under sole responsibility that WEG electric motors and components used for following motor lines: W30 Smart EC – WEG Electronically Commutated Motor BLDC – Permanent Magnetic Synchronous Motor (Al) when installed, maintained and used in applications for which they were designed, and in compliance with the relevant installation standards and manufacturer’s instructions, comply with the provisions of the following relevant European... -
Page 17: Declaration Of Conformity
No.2226, South Second Ring East Road, Jintan District, Changzhou City, Jiangsu Province, China. www.weg.net/cn declares under sole responsibility that WEG electric motors and components used for following motor lines: W30 Smart EC – WEG Electronically Commutated Motor BLDC – Permanent Magnetic Synchronous Motor (Al) when installed, maintained and used in applications for which they were designed, and in compliance with the relevant installation standards and manufacturer’s instructions, comply with the provisions of the following relevant European Union... - Page 18 +55 47 3276.4000 motores@weg.net Jaraguá do Sul - SC - Brazil Cod:50143194 | Rev: 00 | Date (m/a): 10/2024. The values shown are subject to change without prior notice. The information contained is reference values.
Need help?
Do you have a question about the W30 Smart EC and is the answer not in the manual?
Questions and answers