Troubleshooting; Two-Year Limited Warranty; Fcc Statement; Support - PowerA Lumectra Overpowered OPS V3 User Manual

TROUBLESHOOTING

EN
PROBLEM: My controller will not power on.
SOLUTION: Confirm the controller is fully charged. Plug in to
recharge as needed.
PROBLEM: I don't see my PC controller listed in my
device's settings.
SOLUTION: Press and hold the SYNC button on bottom of
controller for 3 seconds to enter pairing mode (LED
will flash rapidly).
PROBLEM: My wireless controller is not pairing.
SOLUTION 1: Confirm the battery is charged by plugging in
USB-C cable.
SOLUTION 2: Confirm you are following the Wireless
pairing process.
SOLUTION 3: Insert paper clip into the Reset Hole as marked above
to reset controller to factory settings.
For latest FAQs, visit www.powera.com/support

TWO-YEAR LIMITED WARRANTY

For warranty details or support with your authentic PowerA
accessories, please visit www.powera.com/support
WARRANTY AGAINST DEFECTS,
AUSTRALIA & NEW ZEALAND CUSTOMERS
This product is provided with a 2-year warranty against defects in
manufacturing or materials from the date of purchase. ACCO Brands
will either repair or replace a faulty or defective product subject to the
conditions of this warranty. Claims under this warranty must be made to
the place of purchase within the warranty period with proof of purchase
by the original purchaser only. Expenses associated with a warranty
claim are the responsibility of the consumer. Conditions of this warranty
are on our website: PowerA.com/warranty-ANZ
7
This warranty is provided in addition to other rights or remedies
available to you under the law. Our goods come with guarantees that
cannot be excluded under the Australian Consumer Law. You are entitled
to a replacement or refund for a major failure and compensation for any
other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
DISTRIBUTOR CONTACT DETAILS
AUSTRALIAN CUSTOMERS: ACCO Brands Australia Pty Ltd
Locked Bag 50, Blacktown BC, NSW 2148
Phone: 1300 278 546 | Email: consumer.support@powera.com
NEW ZEALAND CUSTOMERS: ACCO Brands New Zealand Limited
PO Box 11-677, Ellerslie, Auckland 1542
Phone: 0800 800 526 | Email: consumer.support@powera.com

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
CAN ICES-003(B)/NMB-003(B)
This device contains licence-exempt transmitter(s)/receiver(s)
that comply with Innovation, Science and Economic Development
Canada's licence-exempt RSS(s). Operation is subject to the following
two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference
that may cause undesired operation of the device.
This equipment complies with IC RSS-102 radiation exposure limits
set forth for an uncontrolled environment.
RF EXPOSURE STATEMENT
This equipment complies with IC RSS-102 radiation exposure limits
set forth for an uncontrolled environment. This transmitter must not
be co-located or operating in conjunction with any other antenna or
transmitter.