Bosch CC404 Installation Manual
  1. Manuals
  2. Brands
  3. Bosch Manuals
  4. Control Panel
  5. CC404
  6. Installation manual
Bosch CC404 Installation Manual

Bosch CC404 Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
CC404
Installation Guide
EN
Solution 844

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CC404 and is the answer not in the manual?

Questions and answers

Related Manuals for Bosch CC404

Summary of Contents for Bosch CC404

  • Page 1 CC404 Installation Guide Solution 844...

  • Page 2: Copyright Notice

    Bosch. material. Except as specified above or where authorised by the Bosch Security Systems Pty Ltd reserves the right to Copyright Act 1968 (Cth), no part of this publication make changes to features and specifications of its may be reproduced, transmitted, modified or stored, products at any time without prior notification.

  • Page 3: Table Of Contents

    Codepad Medical Alarm .........25 Hold-Down Functions........41 4.11 Isolating Zones ..........25 6.3.1 Arming the System in AWAY Mode..... 41 4.11.1 Standard Isolating ..........25 6.3.2 Arming the System in STAY Mode 1.... 41 Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 4 Call Back Telephone Number ......55 15.20 System Status Reporting Options ....72 11.12 Ring Count ............55 15.21 Test Reporting Time ........72 11.13 Telephone Line Fault Options ......56 15.22 Test Reporting Dialler Options ...... 73 Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 5 CC816 Alarm Link Software......89 19.8 CP5 Eight Zone LED Codepad (CP508W) ............89 19.9 CP5 Eight Zone LCD Codepad (CP508LW)............89 19.10 CP105A Night Arm Station......89 19.11 CC911 Phone Controller.........89 19.12 DD901 Hand Held Dialler Tester ....89 Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 6 Table 36: 4+2 Transmission Code Descriptions ..48 Table 37: Zone Status Display Descriptions ....50 Table 38: SMS Text Messages ........51 Table 39: Dialling Digits ..........52 Table 40: Telco Arm or Disarm Dialling Digits..54 Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 7: Introduction

    0 in all locations other than the telephone Separate Fire Alarm sound • numbers for Receiver 1 and Receiver 2, and the EDMSAT – Satellite Siren-compatible Call Back Telephone Number. • Zone lockout Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 8: Setting The Date And Time

    To set the date and time for the 1st January 2006 at Reserved 24-Hour Fire 10:30 PM, enter: 24-Hour Medical Chime only [2 5 8 0 6][AWAY][0 1 0 1 0 6 2 2 3 0][AWAY] 24-Hour Panic Zone not used Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 9: Programming

    Primary Telephone Number for Receiver 1. The codepad indicators display the current data Refer to Section 2.5 Installer’s Programming Commands stored in this location. on page 11 for more information about using Installer’s Programming Mode. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 10: Programming With The Hand-Held Programmer

    Failure to do this can corrupt the control panel’s memory, in which case you must return the control panel to Bosch Security Systems to unlock the control panel’s memory. A service fee is charged. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 11: Programming With The Programming Key

    Refer to Section 2.5.9 on page 16. Systems to unlock the control panel’s Display the software version number or memory. A service fee is charged control panel type Refer to Section 2.5.10 on page 17. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 12: Command 958 - Enable/Disable Zone Status Mode

    7 are sealed. 5. Remove the programming key from the control panel. Failure to exit Installer’s Programming Mode before removing the programming key can corrupt the data in the programming key. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 13: Command 960 - Exit Installer's Programming Mode

    Section 22.0 on page 98. You can reset the control panel from any location. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 14: Command 963 - Copy The Programming Key To The Control Panel

    2. Connect the programming key to the corrupt the data in the programming key. PROGRAMMING KEY pins (next to the Auxiliary Module socket) at the top of the control panel’s printed circuit board. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 15: Command 964 - Erase The Programming Key

    Two beeps sound and the system returns to the disarmed state. 7. Remove the programming key from the hand- held programmer. Failure to exit Installer’s Programming Mode before removing the programming key can corrupt the data in the programming key. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 16: Command 966 - Enable Or Disable Auto Step Mode

    Installer’s Programming Mode. The remote codepad displays the data stored in Location 000. 2. Enter [9 6 6 #]. Two beeps sound. To disable Auto Step Mode: Enter [9 6 6 #]. Two beeps sound. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 17: Command 999 - Display The Panel Type Or

    Two beeps sound and the hand-held programmer If the Installer Code is unknown, you must return the or remote codepad shows the data programmed control panel to your Bosch Distributor for exchange. in Location 000. A nominal fee applies for this service.
  • Page 18 The control panel is now successfully reset to the Code, you must return the control panel to factory settings. Bosch Security Systems for exchange. A service fee is charged to unlock the control panel’s memory. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 19: Codepad Indicators

    Mode 1. • Section 14.3.4 on page 65 to set zones to automatically isolate in STAY Mode 1. • Section 4.5 on page 23 to arm the system in STAY Mode 2. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 20: Cp5 Eight Zone Lcd Codepad

    Installer’s Programming Mode or you are using a Master Code function. The ON indicator also lights when the system is armed in STAY Mode 1 or STAY Mode 2. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 21 Section 6.1.4 on page 34 to use the Installer Code to set zones to automatically isolatd in STAY Mode 2. • Section 6.2.5 on page 39 to use the Master Code to set zones to automatically isolate in STAY Mode 2. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 22: System Operations

    AWAY Mode, forced arming is not permitted. If this is the case, you seal all zones or manually isolate them before you can arm the system. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 23: Disarming The System From Stay Mode 1

    Exit Time expires. At the end of Exit Time, the zone You cannot use method two unless both indicators turn off and the codepad sounds one short Options 2 and 4 are enabled in beep. Location 429. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 24: Codepad Duress Alarm

    Mode 2 reports as User Code16. to 0 (refer to Section 15.9 Codepad Panic Report on page 70). A codepad Panic Alarm transmits Contact ID Event Code 120 if the system reports to a base station receiver. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 25: Codepad Fire Alarm

    A Zone armed. Bypass Restore Report is transmitted when the system 4. Repeat Step 3 for each zone to isolate. is disarmed. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 26: Fault Analysis Mode

    To enable monitoring of the horn speaker, select Option 2 in Location 424 (refer to Section 18.1 System Options 1 on page 84). Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 27 The control panel waits 10 minutes before it tries to report to the base station receiver up to six more times. The communication fault resets after the next successful call. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 28: Remote Radio Transmitter Operations

    ID code. Two beeps sound and the STAY and AWAY indicators turn off. 4. Repeat Steps 1 through 3 to add or change another remote radio User Code. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 29: Two-Channel Remote Radio Hand-Held Transmitter Operations

    If Option 1 is selected in Location 425 (refer to Section 18.2 System Options 2 on page 84), the remote radio Panic Alarm is also silent. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 30: Four-Channel Remote Radio Hand-Held Transmitter Operations

    If strobe and 8. Reset times vary depending on the indications are enabled, the strobe flashes for 6 polarity used. seconds to indicate the system is armed. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 31: System Functions

    Step 5. the first Test Report is sent. 4. Repeat Steps 2 and 3 to program another phone number. 5. Press [AWAY] to exit this mode. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 32: Sequence

    Table 21: Codepad Indicators When Changing Phone Numbers Table 23: Codepad Indicators When Changing the Telco Arming or Disarming Zone Indicators MAINS Sequence Digit Indicator Zone Indicators MAINS Digit Indicator Pause Break Pause Break Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 33 These two beeps normally sound after the last digit of the sequence is shown. 3. Press [STAY][2 6 1][STAY][2][AWAY]. Two beeps sound and the system returns to the disarmed state. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 34: Setting Stay Mode 2 Zones

    Enter the Installer Code and press [6][AWAY]. Two beeps sound and the system returns to the Two beeps sound. disarmed state. The indicators for the zones you selected and the STAY indicator turn off. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 35: Walk Test Mode

    Resetting a disarmed 24-Hour Alarm is indicated by a beep only. After the last event, three beeps sound to indicate the end of playback. You can stop the replay at any time by pressing [AWAY]. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 36: Changing And Deleting User Codes

    This function allows a Master Code holder to change or delete a remote radio User Code. One long beep indicates the code already exists or that you entered an incorrect user number. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 37: Changing Domestic Phone Numbers

    If you are not programming other numbers, go to Step 5. 4. Repeat Steps 2 and 3 to program another phone number. 4 sec pause 5. Press [AWAY] to exit this mode. break Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 38: Table 30: Codepad Indicators When Changing Telco Arming Or Disarming Sequence

    AWAY Mode, enter: 4. Press [STAY][2][AWAY]. Two beeps sound and the system returns to the [2 5 8 0 3][AWAY][1][AWAY][STAY] disarmed state. [1 6 1 9 6 7 2 1 7 7 7][STAY][2][AWAY] Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 39: Setting Stay Mode 2 Zones

    Three beeps sound and the STAY indicator flashes. 2. Enter the number of the zone you want to automatically isolate and press [STAY]. The corresponding zone indicator flashes. 3. Repeat Step 2 to select each zone. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 40: Setting The Date And Time

    To enter Walk Test Mode: 1. Enter your Master Code and press [7][AWAY]. Three beeps sound and the STAY and AWAY indicators flash. The codepad beeps once per second when Walk Test Mode is active. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 41: Hold-Down Functions

    Refer to Table 14 on page 26. To exit Fault Analysis Mode: Press [AWAY]. The STAY and AWAY indicators turn off and the system returns to the disarmed state. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 42: Initiate A Modem Call

    When this occurs, Number is 0000. This feature only applies if the modem negotiating tones sound rather control panel is programmed to report by telephone. than the remote arming jingle. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 43: Alarm Link Software

    2. Select Options 1 and 2 in Location 180 (refer to verification. Remember that using this feature reduces Section 8.2 Alarm Link Options on page 44). the security of the control panel. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 44: Direct Connect

    If an alarm occurs when the control panel is communicating with a remote computer using the CC816 Alarm Link Software, the Alarm Link session ends and the alarm message is sent to the base station receiver. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 45: Domestic Dialling

    The disarmed state. identification beep is programmed in Location 039 of the Subscriber ID Number for Receiver 1 or Location 079 of the Subscriber ID Number for Receiver 2. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 46: Table 28: Domestic Dialling Digits

    7. Repeat Step 6 for each additional phone number. 8. After the last digit of the last telephone number, press [AWAY] to exit this mode. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 47: Dialler Reporting Formats

    Zone Specific 1 to 8 Sensor Watch Sensor Self Test Failure 15.3 Zone Specific 1 to 8 Trouble Sensor Trouble 15.2 Zone Specific 1 to 8 Bypass Zone Bypass 15.1 Fuse Fail System Trouble 15.13 Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 48: Point Id Codes

    Receiver 1 and Receiver 2 on page 53). 4. Program Basic Pager Format (Option 5) in Location 033 (refer to Section 11.4 Transmission Format for Receiver 1 and Receiver 2 on page 53). Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 49: Figure 7: Basic Pager Display

    1– Alarm 1 – AC Failure 2 – Zone Bypassed 8 – 0 – System Normal 3 – Zone Trouble 1 – System Fault 5 – 8 – Disarmed 9 – Armed Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 50: Basic Pager Display Information

    The third digit indicates the status of the AC mains supply. The fourth digit indicates whether a system fault occurred at the control panel (refer Section 4.12 Fault Analysis Mode on page 26 for more information. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 51: Sms Reporting

    0000 and 9999 assigned by the Zone 07 installer. Fuse Fail <Subscriber ID> Fuse Fail Fuse Reset <Subscriber ID> Fuse Fail x = 1 to 16 y = 01 to 16 Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 52: Dialler Information

    To enter a 4-second pause in the dialling sequence, program a 13. A pause might be necessary when the dialler communicates through an old (slower) telephone exchange or when a PABX system is in place. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 53: Secondary Telephone Number For Receiver 1 And Receiver 2

    4 – No Handshake 0 0 4 7 2 9 Setting these locations to No Handshake Tone is not recommended. 5 – Pager Pager Handshake Tone is required to communicate in Basic Pager Format. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 54: Dialling Format

    AWAY Mode, program: [11 6 1 9 6 7 2 1 10 5 5 12 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0] Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 55: Telco Disarming Sequence

    “Ring, Ring – Ring, Ring” and that a Ring Count of 10 represents approximately 60 seconds. This location has an effect only if Remote Arming, Remote Upload/Download using Alarm Link, or both are enabled. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 56: Telephone Line Fault Options

    If you program 7 in this location, the horn speaker, bell, strobe, and EDMSAT outputs are all activated when the system is armed or disarmed. 8 – Reserved Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 57: Dialler Options

    If this option is selected, the control panel uses the BELL 103 transmission frequency at 300 baud. If this option is not selected, the control panel uses the CCITT V21 transmission frequency at 300 baud. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 58: Dialler Options 3

    60/40. This option has no effect when using DTMF tone dialling. 8 – Reserved 12.4 Alarm Link Options For more information about this location, refer to Section 8.2 Alarm Link Options on page 44. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 59: Access Code

    15 15 15 15 RF User #14 250 to 254 15 15 15 15 RF User #15 255 to 259 15 15 15 15 RF User #16 260 to 264 15 15 15 15 Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 60: User Code Priority

    Arm Only The user can arm the system but cannot disarm the system. A Closing Report is sent only after a previous code that can send an Opening Report disarms the system. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 61: Zone Information

    EOL resistors. This feature also increases the security of the system because eleven possible EOL resistor values can be used, which makes it extremely difficult to tamper with the system. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 62: Figure 8: Split Eol Resistors Using Nc Contacts

    2 – Zone 2 7 – Zone 7 3 – Zone 3 8 – Zone 8 Ω 4 – Zone 4 9 – 3.3 k Ω 5 – Zone 5 10 – 6.8 k Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 63: Zone Programming

    You can page 81). After Entry Time expires, the system disable sequential handover by disabling Option 8 in activates an alarm. Location 426 (refer to Section 18.3 System Options 3 on page 85). Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 64: Zone Pulse Count

    A 24-Hour Burglary handover pulses from other zones. 24- zone does not send a Restore Report until the zone is Hour zones can hand over pulses to other restored. zones. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 65: Zone Pulse Count Time

    12 hours each day, it takes 4 days before a zone sirens to stop before re-entering the premises. can register a Sensor Watch fault. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 66: Keyswitch Zone Options

    STAY Mode 1, or STAY Mode 2 when using the type. momentary keyswitch input. Arming the system is not Refer to Section 4.3 Arming the System in STAY Mode 1 permitted from the Keyswitch Zone. on page 22 for more information. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 67: Zone Report Code

    Table 46: Zone Dialler Options Option Description No report required Receiver 1 Receiver 2 Receiver 1 and Receiver 2 Receiver 2 only when Receiver 1 fails Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 68: Swinger Shutdown Count For Dialler

    Swinger Shutdown Count for the Dialler resets to 6 and the process of swinger shutdown for the remaining zones, including Zone 1, begins again until all zones are locked out. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 69: System Reporting Information

    Restore code and is global for all zones. A zone Restore Report is sent only to the receiving party to which the zone is allocated (for example, Receiver 1 or Receiver 2). Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 70: Zone Status Reporting Options

    Restore Reports are not sent for this event. Receiver 2 Receiver 1 and Receiver 2 If Fire Reports are not required, program Receiver 2 only when Receiver 1 fails Locations 339 and 340 as 0. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 71: Codepad Medical Report

    Outputs 1 to 4 do not operate when the accessories fuse is replaced. The system reports the control panel detects a low battery. event approximately 10 seconds after the fuse is replaced. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 72: System Status - Low Battery Restore Report

    First Test Report on page 31 to set the first test report. programmed in Location 410 (refer to Section 17.8 Codepad Lockout Time on page 82). • Sends an Access Denied Report (Contact ID Event Code 421) to the base station receiver. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 73: Test Reporting Dialler Options

    Table 52 lists the reporting options. Table 52: Test Reporting Options Option Description No Test Reports required Receiver 1 Receiver 2 Receiver 1 and Receiver 2 Receiver 2 only when Receiver 1 fails Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 74: Programmable Outputs

    Output Event Type. This output operates when the system is armed in STAY Mode 1 or STAY Mode 2. The output resets when the system is disarmed. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 75 If the output is activated by Entry Timer 1, Entry Timer 2, or Entry Guard Timer for STAY Mode, the output resets when the Entry Time expires or the system is disarmed. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 76 This output operates when a user activates a Codepad Medical Alarm by pressing [4] and [6] at the same time on the remote codepad. This output resets when a valid User Code is entered at the remote codepad. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 77 ZONE PULSE COUNT = 3 Dialler Active ZONE PULSE COUNT TIME = 15 This output operates when the communication dialler is on-line. The output resets when the communication dialler releases the telephone line. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 78: Output Polarity

    This polarity is ideally suited for lighting control. You can use a PIR to activate an output to turn on lights. Whenever there is movement, the PIR reactivates the output and lengthens the time the lights remain on. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 79: Output Timing

    Because the output switches back to 0 V when the one-shot time expires or when the event returns to normal, the one- shot timer can be shortened regardless of the time setting. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 80: Pulsing Polarities

    200 ms to 19.8 sec 200 ms ±200 ms 1 to 99 sec 1 sec ±1 sec 1 to 99 min 1 min ±1 min 1 to 99 hr 1 hr ± hour Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 81: System Event Timers

    The remote codepad always sounds one short beep at places objects in the view of a motion detector, the end of Exit Time when arming in STAY Mode 1 preventing the detector from picking up movement. or STAY Mode 2. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 82: Codepad Lockout Time

    To solve the problem, Type 0,5 Auto Arm Pre-Arming Alert Time (refer to program the automatic arming time as page 75). 25:00 hours if you only want the control panel to disarm. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 83: Kiss-Off Wait Time

    A Master Code holder can also set the System Date and Time (refer to Section 6.2.7 Setting the Date and Time on page 40). Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 84: System And Consumer Options

    To disable the reporting of a Codepad Medical Alarm, program Locations 341 and 342 as 0 (refer to Section 15.11 Codepad Medical Report on page 71). Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 85: System Options 3

    8 to 15. Refer to Section 14.3.2 Zone Pulse Count on page 64 and Section 14.3.3 Zone Pulse Count Time on page 65 for more information. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 86: Consumer Options 1

    4 – Alarms Activate Sirens and Strobe Outputs in STAY Modes 1 and 2 Select this option if audible alarms are required when the system is armed in STAY Mode 1 or 2. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 87: Radio Input Options

    3 – Momentary Keyswitch Input Selecting this option allows you to connect a momentary keyswitch to the JP3 terminals D and GND to remotely arm and disarm the system in AWAY Mode. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 88: Optional Equipment

    4 – Red wire configuration data such as monitoring station telephone numbers and zone reporting channels. 5 – Black wire 6 – Termination for phone line 7 – Socket for telecom lead connection Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 89: Cc816 Alarm Link Software

    You can connect multiple detectors The PS100 Power Supply Module provides 13.8 VDC to the same interface. at currents up to 1 A. Use the module with the TF008 18 VAC plug pack. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 90: Cc813 Radio Key/Keyswitch Interface

    If the R/K terminal is used, you can connect a control by hand-held radio remote. number of momentary keyswitches in parallel for multiple arm and disarm locations. Use the ON and OFF terminals to connect directly with any access control system. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 91: Terminals And Descriptions

    EOL resistor. The function of the zones and their response times are configured using the system programming options. If split EOL is programmed, 24-Hour Zones or Keyswitch Zones connected in parallel to Zones 1 and 2 act as Zones 5 and 6. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 92: Glossary Of Terms

    The sirens activate only once per zone per arming cycle. Master Code A numeric code used for arming and disarming the system, and for allowing access to all functions available through the codepad. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 93 A monitored input where tamper switches and emergency switches can be connected. If one of these switches is violated at any time (if the system is armed or disarmed), an alarm is reported. Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 94: Diagrams

    22 – Battery 5 – Zone 2 14 – Smoke detector 23 – 18 VAC 1.3 A plug pack 6 – Zone 6 (TF008) 24 – Link between +12 V and Comm Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 95: Figure 13: Solution 844 Component Overlay

    11 – 1 A accessory fuse cable 12 – 1 A codepad fuse 5 – Zone termination strip 13 – Battery input 6 – Relay contact select 14 – Plug pack input (Bosch TF008) Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 96: Figure 14: Telecom Connection Diagram For Australia

    4 – 4P4C plug (top view) (red): telecom line (street) 5 – RJ12 plug (top view) 9 – Yellow wire 6 – Telecom line 10 – Green wire 7 – Internal phones Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...

  • Page 97: Specifications

    This equipment shall not be set up to make handling, or the damage was not due to causes automatic calls to the Telecom 111 Emergency beyond the control of Bosch Security Systems, such as Service. lightning, excessive voltage, mechanical shock, or...

  • Page 98: Programming Sheets

    0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 159 to 174 anywhere else 0 = 0 Call Back Telephone Number Refer to page 55 Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 99 Alarm Link Options 4 Exit upload/download connection on alarm Refer to page 44 8 External modem module (CC811) required 181 to 184 1 2 3 4 Installer Code Refer to page 59 Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 100 EOL Resistor Value 2 1K5 6 4K7 10 12K 14 Reserved Refer to page 61 3 2K2 7 5K6 11 22K 15 Split EOL (3K3/6K8) : Four burglary zones and four 24-hr zones Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 101 5 Latching arm in STAY Mode 12 Momentary arm and disarm in STAY Mode 6 Latching disarm from STAY Mode 13 Momentary arm in STAY Mode 14 Momentary disarm from STAY Mode Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 102 System Status – Fuse Fail Restore Report Refer to page 71 Location 348: tens digit 10 2 348 to 349 Location 349: units digit System Status – AC Fail Report Refer to page 71 Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 103 14 Normally low, latching open 7 Normally open, latching low The fourth location of the output definition is the time base. The options are: 1 200 ms 1 min 2 1 sec 1 hr Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 104 Refer to page 83 Reserved 1 Bosch smart lockout allowed 2 Horn speaker monitor System Options 1 4 Strobe indication for radio arm/disarm Refer to page 84 8 Horn speaker beeps for radio arm/disarm Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 105 Location 907: Month of the year (tens digit) Refer to page 83 Location 908: Month of the year (units digit) Location 909: Current year (tens digit) Location 910: Current year (units digit) Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 106 Low Battery ..............26 MAINS ................19 Sensor Watch ..............26 MAINS Indicator............21 Fault Analysis Mode ............26 Off Indicator..............21 Exit ..................41 On Indicator..............21 FAULT Indicator ............20, 21 STAY ................19 Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 107 Telephone Line Fail ............76 Phone Controller ............89 Zone Not Sealed ............78 Programming Key............88 Zone Not Sealed After Exit Time ........78 PS100 Power Supply ............ 89 Radio Key/Keyswitch Interface ........90 Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 108 Chime Zone ..............64 Setting Zones ............34, 39 Delay-1 Zone..............63 Strobe Test ................. 41 Delay-2 Zone..............63 System Disarmed .............. 21 Handover Zone..............63 System Operations Instant Zone ..............63 Arming In AWAY Mode..........22 Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 109 CC404 | Installation Guide | Notes Notes Bosch Security Systems | 9/05 | PRELIMINARY F01U009495Ar3...
  • Page 110 Bosch Security Systems 25 Huntingwood Drive Huntingwood NSW 2148 Australia Phone: +612 9672 1777 Facsimile: +612 9672 1717 © 2005 Bosch Security Systems PRELIMINARY F01U009495Ar3 SKU:920053...

Table of Contents