Monogram ZV900 Installation Instructions Manual

36” glass canopy chimney vent hood

Hide thumbs Also See for ZV900:

Installation instructions manual (40 pages)

Owner's manual (24 pages)

Owner's manual (12 pages)

Table Of Contents

Quick Links

Download this manual

INSTALLATION

INSTRUCTIONS

36" Glass Canopy

Chimney Vent Hood

ZV900

MONOGRAM.COM

Table of Contents

Need help?

Do you have a question about the ZV900 and is the answer not in the manual?

Questions and answers

Summary of Contents for Monogram ZV900

Page 1 INSTALLATION INSTRUCTIONS 36” Glass Canopy Chimney Vent Hood ZV900 MONOGRAM.COM...
Page 2 Completion Time — 1 to 3 Hours. covered under the warranty. tension accidentelle. S’il n’est pas possible de monogram.com. monogram.ca monogram.com/use-and-care/parts. wiring must be done by qualified person(s) in CAUTION accordance with all applicable codes and standards Due to the weight and size of these including fire-rated construction.
Page 3: Product Dimensions And Clearances
The telescopic duct cover conceals the ductwork running from the top of the hood to the ceiling. The This hood can be installed over any Monogram electric cooktop or gas cooktop. It cannot be heights. or range.
Page 4: Advance Planning
Installation Preparation ADVANCE PLANNING POWER SUPPLY IMPORTANT - (Please read carefully) WARNING AVERTISSEMENT configurations. Remove house fuse or open circuit breaker before outdoors. beginning installation. air system in accordance with local building prevailing local codes and ordinances. code requirements. Visit GEAppliances.com for Electrical supply available makeup air solutions.
Page 5: Duct Fittings
Installation Preparation DUCT FITTINGS Total Equivalent Quantity Equivalent This Hood Must Use an 8” Round Duct Piece Dimensions Length* Used Length Duct. It Can Transition to a 1 ft. (per foot 3-1/4” x 12” Duct. straight length) 1 ft. (per foot straight length) for duct runs to outdoors.
Page 6: Tools And Materials Required
Installation Preparation TOOLS AND MATERIALS REQUIRED (NOT SUPPLIED) Tape measure Knife Spirit level Spirit level Measuring tape Knife Electric drill with 5/16” and 3/8” bits Hammer Electric drill with 5/16” Safety glasses and 3/8” Bits Duct tape stripper Tape to mount template Duct tape Safety glasses Strain relief for junction cover...
Page 7: Determine Installation Height
Installation Preparation DETERMINE INSTALLATION HEIGHT Wall Mount ZV900 Installation Heights *Possible Actual Ceiling *Possible VENTED the ductwork running to the ceiling. RECIRCULATING Height Installation Height Installation Height 24” to 26” 24” to 26” 8’-1” 24” to 28” 24” to 28”...
Page 8: Check Installation Hardware
Installation Preparation CHECK INSTALLATION HARDWARE Locate and count screws for recirculating Duct bracket installation only 12" 2-piece decorative duct 3 wall 29-7/8" cover (dimension shown fasteners 27-3/4" 3 wood for reference only) screws 3 wall bracket screws 11-1/2" 11-1/2” 12 hood attachment 2 thumb screws...
Page 9: Installation-Vented To The Outside
Installation Instructions INSTALLATION—VENTED TO THE OUTSIDE DUCTWORK, WIRING LOCATIONS INSTALL FRAMING FOR HOOD SUPPORT IMPORTANT — 8-1/2” min. opening for ductwork wall. 5-1/2” c enterline to wall View from rear cleats Ceiling 8-1/2” dia. hole Centerline 26” above the marked bottom pencil line for installation height.
Page 10: Install Mounting Bracket
Installation Instructions INSTALLATION—VENTED TO THE OUTSIDE INSTALL MOUNTING BRACKET INSTALL DUCT BRACKET This vent hood must be secured to the horizontal The duct bracket should be installed against the back support or wall studs. wall and flush with the ceiling. This bracket will hold the duct cover in place at the top.
Page 11: Prepare The Hood
Installation Instructions INSTALLATION—VENTED TO THE OUTSIDE PREPARE THE HOOD Carefully lay the hood on its back. using 6 screws. mounting hooks at the back. side slots at the top rear opening. Rear Bottom view mounting hooks Rear side Rear view Engage flange on motor housing into slots...
Page 12: Mount The Hood
Installation Instructions INSTALLATION—VENTED TO THE OUTSIDE MOUNT THE HOOD CONNECT DUCTWORK WARNING 2 people are required to lift and of airflow as illustrated. position the hood onto the mounting bracket. AVERTISSEMENT lever et mettre en place la hotte sur le support de montage.
Page 13: Connect Electrical
Installation Instructions INSTALLATION—VENTED TO THE OUTSIDE CONNECT ELECTRICAL Verify that power is turned off at the source. a strain relief. WARNING If house wiring is not 2-wire with a House wiring copper connectors. AVERTISSEMENT Si le câblage de la maison n’est pour l’aluminium-cuivre.
Page 14: Install Duct Covers
Installation Instructions INSTALLATION—VENTED TO THE OUTSIDE INSTALL DUCT COVERS INSTALL FILTERS IMPORTANT: covers on top of the hood. Mounting screws NOTE: The inside (upper) duct piece has holes on one end. The holes are intended for use when the hood is installed for recirculating purposes.
Page 15: Installation-Recirculating
Installation Instructions INSTALLATION—RECIRCULATING DUCTWORK, WIRING LOCATIONS INSTALL FRAMING FOR HOOD SUPPORT IMPORTANT — View from rear cleats Ceiling mounting support Centerline of installation space LEVEL. the top mounting brackets. Remove the template. centerline on the template to the ceiling. HOUSE WIRING LOCATION: at the bracket location indicated on the template.
Page 16 Installation Instructions INSTALLATION—RECIRCULATING INSTALL MOUNTING BRACKET INSTALL DUCT BRACKET This vent hood must be secured to the horizontal The duct bracket should be installed against the back support or wall studs. wall and flush with the ceiling. This bracket will hold the duct cover in place at the top.
Page 17 Installation Instructions INSTALLATION—RECIRCULATING PREPARE THE HOOD MOUNT THE HOOD WARNING 2 people are required to lift and position the hood onto the mounting bracket. AVERTISSEMENT mounting hooks at the back. lever et mettre en place la hotte sur le support de side slots at the top rear opening.
Page 18: Size And Cut Duct Piece
Installation Instructions INSTALLATION—RECIRCULATING SIZE AND CUT DUCT PIECE CONNECT ELECTRICAL Verify that power is turned off at the source. the ceiling. WARNING If house wiring is not 2-wire with top of the hood as shown. Reduce that dimension by 1” to facilitate installation. The duct will cover and overlap the deflector and the hood outlets.
Page 19 Installation Instructions INSTALLATION—RECIRCULATING INSTALL DUCT COVERS INSTALL FILTERS Mounting IMPORTANT: screw holes covers on top of the hood. NOTE: The inside piece has Charcoal filter holes on one end intended for use when the hood is installed for opening. Secure the filter with thumbscrews on Vent holes recirculating purposes.
Page 20 NOTE: safety glasses or goggles should be worn. ® monogram.com. NOTE: and specifications are subject to change without notice. 49-80328 Rev. 4 10-19 GEA Printed in Mexico...

This manual is also suitable for:

Zv900slss