Related Manuals for Uniks R18
Summary of Contents for Uniks R18
- Page 1 V 1.0 16-04.2024 Voltage Detector and Phase rotation indicator User Manual V 1.0 16-04.2024...
- Page 2 V 1.0 16-04.2024...
-
Page 3: Register Your Product
V 1.0 16-04.2024 REGISTER YOUR PRODUCT www.uniks.it The registration of your products will allow you to stay informed about news, take advantage of advantageous discounts dedicated to you for the purchase of accessories and products for your daily work. Registration is free... -
Page 4: Table Of Contents
V 1.0 16-04.2024 Safety Instructions ............5 Panel Description ............7 Operation Instructions ..........9 Power On/Off the Detector ......9 Flashlight/Non-contact Voltage Detection Sensitivity Adjustment Key ....... 9 AC Voltage Detection........9 Neutral Line/Phase Line Discrimination ... 10 Non-contact Phase Sequence Detection .. 11 Auto shutdown .......... -
Page 5: Safety Instructions
V 1.0 16-04.2024 1. Safety Instructions WARNING To prevent the risk of electric shock or personal injury： ⚫ Please strictly follow the instructions provided in this manual. Failure to do so may compromise the protection function of the detector. ⚫ Do not use it if the display screen light is not illuminated normally. - Page 6 V 1.0 16-04.2024 Do not use the detector if it is damaged or not working ⚫ properly. Please check the probe carefully before using it ensure that there are no cracks or breaks, and send the ⚫ detector for repair in time if you have any concerns Do not exceed the rated voltage indicated on the detector ⚫...
-
Page 7: Panel Description
V 1.0 16-04.2024 2. Panel Description ① Sensing Probe ② LCD Display Area ③ Power Switch Key ④ Flashlight/Non-contact Voltage Detection Sensitivity Adjustment Key ⑤ Non-contact Phase Sequence Detection Key ⑥ Battery Cover... - Page 8 V 1.0 16-04.2024 Display screen description ⑦ Strong induction signal or Phase 3 Line ⑧ Medium induction signal or Phase 2 Line ⑨ Weak induction signal or Phase 1 Line ⑩ Battery under-voltage symbol ⑪ Reverse phase sequence symbol ⑫ Forward phase sequence symbol ⑬...
-
Page 9: Operation Instructions
V 1.0 16-04.2024 3. Operation Instructions 3.1 Power On/Off the Detector Power On: Press the power switch key for about more than 1 second, a beep sounds, and the screen lights up. Power Off: In the powered-on state of the detector, press the power switch key, and the screen goes off. -
Page 10: Neutral Line/Phase Line Discrimination
V 1.0 16-04.2024 the live wire. When the detector detects the AC voltage signal, the LCD backlight changes from white to red. The instrument displays the signal strength based on the detected signal strength, the LCD displays the strength of the induced signal, and the buzzer emits different alarm sounds. -
Page 11: Non-Contact Phase Sequence Detection
V 1.0 16-04.2024 3.5 Non-contact Phase Sequence Detection After power on, press the “ ” key to switch until the display screen shows the “3-P” symbol to enter the phase sequence detection state. a) Attach the sensing probe tightly to the first phase line, wait for a beep from the buzzer, and at the same time, the screen displays the “L1”... - Page 12 V 1.0 16-04.2024 ⚫ The “ ” symbol represents counterclockwise (reverse sequence), and the buzzer beeps 6 times continuously; the “ ” symbol represents clockwise (forward sequence), and the buzzer beeps once.。 ⚫ lease complete the test of the three wires in about 1 minute, otherwise a detection timeout error will occur, and the instrument will light up the red backlight to prompt (“...
-
Page 13: Auto Shutdown
V 1.0 16-04.2024 3.6 Auto shutdown The tester will automatically shut down if it is left idle for approximately 5 minutes and no AC voltage signal is detected. 3.7 Low battery voltage alert The “ ” icon flashes when the battery voltage drops below approximately 2.6V. -
Page 14: Battery Replacement
V 1.0 16-04.2024 4. Battery replacement According to the following picture: 1. Rotate the battery cover as indicated. 2. Remove dead batteries. 3. Ensure that new batteries are inserted in the correct polarity. NOTE: Be sure to check the rubber waterproof ring when you put the battery cover back on, as the waterproof effect may be affected if any misalignment or falling off occurs... -
Page 15: Technical Specifications
V 1.0 16-04.2024 5. Technical Specifications 12 ~1000V (sound and light alerts within the detection AC voltage detection range range).Frequency： 50Hz/60Hz Press the button to select high AC voltage detection sensitivity sensitivity or low sensitivity (default) Induction intensity High, medium, low According to the intensity of the induction signal, the live wire is Neutral/Live wires... - Page 16 V 1.0 16-04.2024 CAT rating CAT IV 600V，CAT III 1000V IP rating IP67 Drop test 1 meters Power supply 2×1.5V AAA batteries Dimensions 168mm×29mm×25mm About 45g (batteries not Weight included) Applicable IEC 61010-1、IEC 60529-2013 standards...
-
Page 17: Assistance
V 1.0 16-04.2024 6. 1ASSISTANCE 6.1 WARRANTY CONDITIONS This instrument is warranted against defects in materials and workmanship, in accordance with the general terms and conditions. During the warranty period, defective parts can be replaced, but the manufacturer reserves the right to repair or replace the product. If the instrument is to be returned to the after - sales service or to a dealer transportation is borne by the customer. - Page 18 V 1.0 16-04.2024 its use with no compatible devices. • Repairs made necessary due to improper packaging. • Repairs made necessary due to work carried out by unauthorized personnel. • Modification of the instrument without the explicit permission of the manufacturer.
-
Page 19: Assistance
V 1.0 16-04.2024 6.2 ASSISTANCE If the instrument does not operate properly, before contacting the Customer Service, check the status of the battery and wear of the cables and replace them if necessary. If the instrument continues to manifest malfunctions check if the procedure of use of the same is in accordance with what is indicated in this manual. - Page 20 V 1.0 16-04.2024 http://www.uniks.it info@uniks.it...
Need help?
Do you have a question about the R18 and is the answer not in the manual?
Questions and answers