1. Manuals
  2. Brands
  3. AstroNova Manuals
  4. Label Maker
  5. QuickLabel QL-300
  6. Accessory manual

AstroNova QuickLabel QL-300 Accessory Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
QL-300 Accessory Guide
Revision 1.0
5/2019
®
QuickLabel, An AstroNova
Division
World Headquarters
600 East Greenwich Ave., West Warwick, RI 02893
Tel: +1 (401) 828-4000 Fax: +1 (401) 822-2430
E-mail: info@QuickLabel.com
www.QuickLabel.com
Technical Support
Tel: +1 (401) 828-4000
E-mail: support@QuickLabel.com
www.QuickLabel.com/support/

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the QuickLabel QL-300 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for AstroNova QuickLabel QL-300

Summary of Contents for AstroNova QuickLabel QL-300

  • Page 1 QL-300 Accessory Guide Revision 1.0 5/2019 ® QuickLabel, An AstroNova Division World Headquarters 600 East Greenwich Ave., West Warwick, RI 02893 Tel: +1 (401) 828-4000 Fax: +1 (401) 822-2430 E-mail: info@QuickLabel.com www.QuickLabel.com Technical Support Tel: +1 (401) 828-4000 E-mail: support@QuickLabel.com...
  • Page 2 © 2019 AstroNova, Inc. All Rights Reserved This manual is copyrighted with all rights reserved. No part of this manual may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form by any means without written permission of QuickLabel.

  • Page 3: Table Of Contents

    Contents Chapter 1: RW-300 Label Rewinder Setup ......4 RW-300 Label Rewinder ....... . . 4 Install the Core Holder .

  • Page 4: Chapter 1: Rw-300 Label Rewinder Setup

    RW-300 Label Rewinder Setup RW-300 Label Rewinder The rewinder has a switching power supply with an input of 1.8A 100-240Vac, 50-60Hz and an output of 24V DC 2.5A. It allows an electronic circuit to adjust the speed of rotation through the tension arm.

  • Page 5: Install The Printer Plate

    RW-300 Label Rewinder Setup Turn the knob in order to tighten the roll. Then lay the core holder onto the core holder supports. Important: The core holder must be positioned with the black matching handle and gray matching handle. Install the Printer Plate Attach the alignment plate to the printer.

  • Page 6: Paper Path

    RW-300 Label Rewinder Setup Paper Path Pull the media under the tension arm and attach it to the cardboard core. Switch on the unit. The label rewinder is ready. QL-300 Accessory Guide...

  • Page 7: Chapter 2: Mr-300 Inline Matrix Remover Setup

    MR-300 Inline Matrix Remover Setup MR-300 Inline Matrix Remover The matrix remover has a switching power supply with an input of 1.8A 100-240Vac, 50-60Hz and an output of 24V DC 2.5A. It allows an electronic circuit to adjust the speed of rotation through the tension arm.
  • Page 8 MR-300 Inline Matrix Remover Setup Tighten using the tension knob. Insert the empty cardboard core on the core holder to receive the new label roll. The core width should be equal to the total label width. Load the outside disk making sure it adheres to the cardboard. Tighten using the tension knob.

  • Page 9: Install The Pressing Roller

    MR-300 Inline Matrix Remover Setup Install the Pressing Roller The pressing roller facilitates the matrix removal from the die-cut roll. Remove it from the rewinder station (there are 4 knobs to unscrew). Unscrew the 10 screws on the top of matrix remover module. Position the matrix remover roller on the matrix remover module and secure it properly with the 10 screws.

  • Page 10: Install The Printer Plate

    MR-300 Inline Matrix Remover Setup Install the Printer Plate Attach the alignment plate to the printer. To get the inline matrix remover aligned to the printer, match the triangles on the second plate with the one on the matrix remover. Tighten the knob to lock the matrix remover to the printer plate.
  • Page 11 MR-300 Inline Matrix Remover Setup Feed the paper as illustrated. Pull the media underneath the last aluminum roller and then separate the waste matrix from the liner. Attach the waste matrix to the empty core on the waste core. QL-300 Accessory Guide...
  • Page 12 MR-300 Inline Matrix Remover Setup Attach the finished printed media to the empty core on the rewinder core. Lock the tension roller. QL-300 Accessory Guide...
  • Page 13 MR-300 Inline Matrix Remover Setup Release the pressing roller. Switch on the unit. The matrix remover is ready. A sample application is shown below. QL-300 Accessory Guide...

This manual is also suitable for:

Rw-300

Table of Contents