TRENDnet TEW-611BRP User Manual
  1. Manuals
  2. Brands
  3. TRENDnet Manuals
  4. Wireless Router
  5. TEW-611BRP
  6. User manual
TRENDnet TEW-611BRP User Manual

TRENDnet TEW-611BRP User Manual

108mpbs 802.11g mimo wireless router
Hide thumbs Also See for TEW-611BRP:
Table of Contents

Advertisement

Quick Links

Download this manual
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TEW-611BRP and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for TRENDnet TEW-611BRP

Summary of Contents for TRENDnet TEW-611BRP

  • Page 2: Federal Communication Commission Interference Statement

    Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

  • Page 3: Table Of Contents

    Table of Contents Getting Started with the TEW-611BRP ………….....3 Package Contents ..............4 Minimum System Requirements ......... …………4 Wireless LAN Networking ............6 Introduction ................7 Features ..................7 Hardware Overview ..............8 Rear Panel ……………………………………………………………8 LEDs ..................9 Installation Considerations ............10 Getting Started ................10 Using the Configuration Menu..........

  • Page 4: Getting Started With The Tew-611Brp

    Getting Started with the TEW-611BRP Congratulations on purchasing the TEW-611BRP! This manual provides information for setting up and configuring the TEW-611BRP. This manual is intended for both home users and professionals. The following conventions are used in this manual: THE NOTE SYMBOL INDICATES ADDITIONAL INFORMATION ON THE TOPIC AT HAND.

  • Page 5: Package Contents

    Package Contents TEW-611BRP 108Mbps 11g MIMO Wireless Router Power Adapter (5V DC, 2A) CD-ROM with Software and Manual Quick Installation Guide Cat.5 Ethernet Cable Using a power supply with a different voltage than the one included with your product will cause damage and void the warranty for this product.

  • Page 6: Wireless Lan Networking

    Wireless LAN Networking This section provides background information on wireless LAN networking technology. Consult the “Glossary” for definitions of the terminology used in this section. HE INFORMATION IN THIS SECTION IS FOR YOUR REFERENCE. HANGING NETWORK SETTINGS AND PARTICULARLY SECURITY SETTTINGS SHOULD ONLY BE DONE BY AN AUTHORIZED ADMINISTRATOR.

  • Page 7: Introduction

    Unlike most routers, the TEW-611BRP provides data transfers at up to 108 Mbps (compared to the standard 54Mbps) when used with other Super G MIMO products. The 802.11g standard is backwards compatible with 802.11b products.

  • Page 8: Hardware Overview

    Hardware Overview Real Panel DC-IN The DC power input connector is a single jack socket to supply power to the TEW-611BRP. Please use the Power Adapter provided on the TEW-611BRP package. Auto-MDIX LAN Ports These ports automatically sense the cable type when connecting to Ethernet-enabled computers.

  • Page 9: Leds

    LEDs POWER LED A solid light indicates a proper connection to the power supply. LAN1~LAN4 LED A solid light indicates a connection to an Ethernet-enabled computer on ports 1-4. This LED blinks during data transmission. WAN LED A solid light indicates connection on the WAN port. This LED blinks during data transmission. WLAN LED This LED blinks during wireless data A solid light indicates that the wireless segment is ready.

  • Page 10: Installation Considerations

    Installation Considerations The TEW-611BRP MIMO Wireless Router lets you access your network, using a wireless connection, from virtually anywhere within its operating range. Keep in mind, however, that the number, thickness and location of walls, ceilings, or other objects that the wireless signals must pass through, may limit the range.

  • Page 11: Using The Configuration Menu

    Open the Web browser. Type in the IP Address of the Router (http://192.168.0.1). If you have changed the default IP Address assigned to the TEW-611BRP, make sure to enter the correct IP Address. Type admin in the User Name field.

  • Page 12: Basic

    Basic The Basic tab provides the following configuration options: Wizard, WAN, LAN, DHCP, and Wireless. Basic_Wizard Internet Connection Setup Wizard This wizard guides you through the following basic router setup steps: • Set your Password • Select your Time Zone •...
  • Page 13 Wireless Security Setup Wizard This wizard guides you through the following steps for setting up security for your wireless network: • Name your Wireless Network • Secure your Wireless Network Basic_WAN The WAN (Wide Area Network) section is where you configure your Internet Connection type. There are several connection types to choose from: Static IP, DHCP, PPPoE, PPTP, L2TP, and BigPond.
  • Page 14 Static WAN Mode Used when your ISP provides you a set IP address that does not change. The IP information is manually entered in your IP configuration settings. You must enter the IP address, Subnet Mask, Gateway, Primary DNS Server, and Secondary DNS Server. Your ISP provides you with all of this information.
  • Page 15 • Always on: A connection to the Internet is always maintained. • On demand: A connection to the Internet is made as needed. • Manual: You have to open up the Web-based management interface and click the Connect button manually any time that you wish to connect to the Internet. Maximum Idle Time: Time interval the machine can be idle before the PPTP connection is disconnected.
  • Page 16 IP address of the router not to respond to ping commands. Pinging public WAN IP addresses is a common method used by hackers to test whether your WAN IP address is valid. WAN Ping Inbound Filter: Select a filter that controls access as needed for WAN pings. If you do not see the filter you need in the list of filters, go to the Advanced ->...
  • Page 17 Basic_LAN These are the settings of the LAN (Local Area Network) interface for the router. The router's local network (LAN) settings are configured based on the IP Address and Subnet Mask assigned in this section. The IP address is also used to access this Web-based management interface. It is recommended that you use the default settings if you do not have an existing network.
  • Page 18 Basic_DHCP DHCP stands for Dynamic Host Configuration Protocol. The DHCP section is where you configure the built-in DHCP Server to assign IP addresses to the computers and other devices on your local area network (LAN). Enable DHCP Server Once your Wireless router is properly configured and this option is enabled, the DHCP Server will manage the IP addresses and other network configuration information for computers and other devices connected to your Local Area Network.
  • Page 19 DHCP IP Address Range These two values (from and to) define a range of addresses that the DHCP Server uses when assigning addresses to computers and devices on your Local Area Network. Any addresses that are outside of this range are not managed by the DHCP Server; these could, therefore, be used for manually configured devices or devices that cannot use DHCP to obtain network address details automatically.
  • Page 20 or nearly full, you need to recover space in the table for new entries, and you know that some of the currently allocated leases are no longer needed. Clicking Revoke cancels the lease for a specific LAN device and frees an entry in the lease table. Do this only if the device no longer needs the leased IP address, because, for example, it has been removed from the network.
  • Page 21 Basic_Wireless The wireless section is used to configure the wireless settings for your Wireless router. Please note that changes made on this section may also need to be duplicated on your Wireless Client. To protect your privacy, use the wireless security mode to configure the wireless security features. This device supports three wireless security modes including: WEP, WPA-Personal, and WPA-Enterprise.
  • Page 22 Wireless Network Name When you are browsing for available wireless networks, this is the name that will appear in the list (unless Visibility Status is set to Invisible, see below). This name is also referred to as the SSID. For security purposes, it is highly recommended to change from the pre-configured network name.
  • Page 23 A method of encrypting data for wireless communication intended to provide the same level of privacy as a wired network. WEP is not as secure as WPA encryption. To gain access to a WEP network, you must know the key. The key is a string of characters that you create. When using WEP, you must determine the level of encryption.
  • Page 24 to generate session keys that are unique for each wireless client. Example: Wireless Networking technology enables ubiquitous communication WPA-Enterprise This option works with a RADIUS Server to authenticate wireless clients. Wireless clients should have established the necessary credentials before attempting to authenticate to the Server through this Gateway.

  • Page 25: Advanced

    Advanced The Advanced tab provides the following configuration options: Virtual Server, Special Applications, Gaming, Traffic Shaping, Routing, Access Control, WEB Filter, MAC Address Filter, Firewall, Inbound Filter, Advanced Wireless and Schedules. Advanced_Virtual Server The Virtual Server option gives Internet users access to services on your LAN. This feature is useful for hosting online services such as FTP, Web, or game servers.
  • Page 26 5. Select the Protocol - TCP 6. Ensure the schedule is set to Always 7. Click Save to add the settings to the Virtual Servers List 8. Repeat these steps for each Virtual Server Rule you wish to add. After the list is complete, click Save Settings at the top of the page.
  • Page 27 virtual server entries, you must still click the Save Settings button at the top of the page to make the changes effective and permanent. Virtual Servers List The section shows the currently defined virtual servers. A Virtual Server can be changed by clicking the Edit icon, or deleted by clicking the Delete icon.
  • Page 28 Application Level Gateway (ALG) Configurations Here you can enable or disable ALGs. Some protocols and applications require special handling of the IP payload to make them work with network address translation (NAT). Each ALG provides special handling for a specific protocol or application. A number of ALGs for common applications are enabled by default.
  • Page 29 192.168.0.255. The computer on the LAN whose MAC address is contained in the magic packet will be awakened. Use this ALG if you are experiencing frequent disconnects from the AOL server due to inactivity. Allows Windows Media Player, using MMS protocol, to receive streaming media from the internet.
  • Page 30 Saves the new or edited Special Applications Rule in the following list. When finished updating the special applications rules, you must still click the Save Settings button at the top of the page to make the changes effective and permanent. With this Special Application Rule enabled, the router will open up a range of ports from 6000-6200 for incoming traffic from the Internet, whenever any computer on the internal network opens up an application that sends data to the Internet using a port in the range of...
  • Page 31 Edit/Add Game Rule Here you can add entries to the Game Rules List below, or edit existing entries. Example: You are hosting an online game server that is running on a PC with a Private IP Address of 192.168.0.50. This game requires that you open multiple ports (6159-6180, 99) on the router so Internet users can connect.
  • Page 32 Advanced_Traffic Shaping The Traffic Shaping™ feature helps improve your network gaming performance by prioritizing applications. By default, the Traffic Shaping settings are disabled.
  • Page 33 Traffic Shaping Setup Enable Traffic Shaping This option is disabled by default. Enable it for better performance and experience with online games and other interactive applications, such as VoIP. Automatic Classification This option is enabled by default so that your router will automatically determine which programs should have network priority.
  • Page 34 displayed here. Add/Edit Traffic Shaping Rule Automatic classification will be adequate for most applications, and specific Traffic Shaping Rules will not be required. A Traffic Shaping Rule identifies a specific message flow and assigns a priority to that flow. Enable Each entry in Traffic Shaping Rules List can be active (enabled) or inactive (disabled) Name Create a name for the rule that is meaningful to you.
  • Page 35 Advanced_Routing Add/Edit Route Adds a new route to the IP routing table or edits an existing route. Enable: Specifies whether the entry will be enabled or disabled. Destination IP: The IP address of packets that will take this route. Netmask: One bits in the mask specify which bits of the IP address must match. Gateway: Specifies the next hop to be taken if this route is used.
  • Page 36 Advanced_Access Control The Access Control section allows you to control access in and out of devices on your network. Use this feature as Parental Controls to only grant access to approved sites, limit web access based on time or dates, and/or block access from applications such as peer-to-peer utilities or games. Enable By default, the Access Control feature is disabled.
  • Page 37 Add/Edit Access Control Rule Access Control Rules specify what a LAN device is allowed to access. Here you can add entries to the Access Control Rules List or edit existing entries. Enable Each entry in Access Control Rules List can be active (enabled) or inactive (disabled) Policy Name Create a name for this access control policy (rule) that is meaningful to you.
  • Page 38 Access Control Rules List This section shows the current access control rules. Rules can be changed by clicking the Edit icon, or deleted by clicking the Delete icon. When you click the Edit icon, the item is highlighted, and the "Edit Access Control Rule" section is activated for editing. Advanced_WEB Filter The Web Filter section is where you add the Web sites to be used for Access Control.
  • Page 39 doubleclick.net. Save Saves the new or edited Allowed Web Site in the following list. When finished updating the Allowed Web Site List, you must still click the Save Settings button at the top of the page to make the changes effective and permanent. Allowed Web Site List The section lists the currently allowed web sites.
  • Page 40 Note: Misconfiguration of this feature can prevent any machine from accessing the network. In such a situation, you can regain access by activating the factory defaults button on the router itself. Filter Settings Mode When "only allow listed machines" is selected, only computers with MAC addresses listed in the MAC Address List are granted network access.
  • Page 41 Advanced_Firewall Enable SPI SPI ("stateful packet inspection" also known as "dynamic packet filtering") helps to prevent cyberattacks by tracking more state per session. It validates that the traffic passing through that session conforms to the protocol. When SPI is enabled, the extra state information will be reported on the Status ->...
  • Page 42 Advanced_Inbound Filter The Inbound Filter option is an advanced method of controlling data received from the Internet. With this feature you can configure inbound data filtering rules that control data based on IP Address. Inbound Filters can be used for limiting access to a server on your network to a system or group of systems.
  • Page 43 Source IP Range Define the ranges of Internet addresses this rule applies to. For a single IP address, enter the same address in both the Start and End boxes. Up to eight ranges can be entered. The Enable checkbox allows you to turn on or off specific entries in the list of ranges. Save Saves the new or edited Inbound Filter Rule in the following list.
  • Page 44 Fragmentation Threshold This setting should remain at its default value of 2346. Setting the Fragmentation value too low may result in poor performance. RTS Threshold This setting should remain at its default value of 2346. If you encounter inconsistent data flow, only minor modifications to the value are recommended.
  • Page 45 Advanced_Schedules Schedules can be created for use with enforcing rules. For example, if you want to restrict web access to Mon-Fri from 3pm to 8pm, you could create a schedule selecting Mon, Tue, Wed, Thu, and Fri and enter a Start Time of 3pm and End Time of 8pm. Add/Edit Schedule Rule In this section you can add entries to the Schedule Rules List below or edit existing entries.
  • Page 46 End Time The end time is entered in the same format as the start time. The hour in the first box and the minutes in the second box. The end time is used for most other rules, but is not used for email events.

  • Page 47: Tools

    Tools The Tools tab provides the following configuration options: Admin, Time, Syslog, Email, System, Firmware and Dynamic DNS. Tools_Admin The Admin option is used to set a password for access to the Web-based management. By default there is no password configured. It is highly recommended that you create a password to keep your new router secure.
  • Page 48 Admin Password Enter a password for the user "admin", who will have full access to the Web-based management interface. User Password Enter a password for the user "user", who will have read-only access to the Web-based management interface. Router Name The name of the router can be changed here.
  • Page 49 -> Internet Options -> Security -> Custom Level -> Medium). Click the Save to Windows Connect Now button, and the WCN technology will capture the wireless network settings from your router and save them on your PC. Note that WCN only saves a few of the wireless security settings. When you use WCN to propagate settings to other wireless devices, you may have to make additional settings manually on those devices.
  • Page 50 Time Configuration Time Zone Select your local time zone from pull down menu. Daylight Saving Enable Check this option if your location observes daylight saving time. Daylight Saving Offset Select the time offset, if your location observes daylight saving time. DST Start and DST End Select the starting and ending times for the change to and from daylight saving time.
  • Page 51 Tools_Syslog This section allows you to archive your log files to a Syslog Server. Enable Logging to Syslog Server Enable this option if you have a syslog server currently running on the LAN and wish to send log messages to it. Enabling this option causes the following parameter to be displayed. Syslog Server IP Address Enter the LAN IP address of the Syslog Server.
  • Page 52 Tools_Email The Email feature can be used to send the system log files, router alert messages, and firmware update notification to your email address. Enable Enable Email Notification When this option is enabled, router activity logs or firmware upgrade notifications can be emailed to a designated email address, and the following parameters are displayed.
  • Page 53 SMTP Server Address Enter the SMTP server address for sending email. Enable Authentication If your SMTP server requires authentication, select this option. Account Name Enter your account for sending email. Password Enter the password associated with the account. Verify Password Re-type the password associated with the account.
  • Page 54 Tools_System This section allows you to reboot the device, and restore the router to the factory default settings. Restoring the unit to the factory default settings will erase all settings, including any rules that you've created. Reboot the Device This restarts the router. Useful for restarting when you are not near the device. Restore all Settings to the Factory Defaults This option restores all configuration settings back to the settings that were in effect at the time the router was shipped from the factory.
  • Page 55 Firmware Information Here are displayed the version numbers of the firmware currently installed in your router and the most recent upgrade that is available. Firmware Upgrade Note: Firmware upgrade cannot be performed from a wireless device. To perform an upgrade, ensure that you are using a PC that is connected to the router by wire.
  • Page 56 Tools_Dynamic DNS The Dynamic DNS feature allows you to host a server (Web, FTP, Game Server, etc.) using a domain name that you have purchased (www.whateveryournameis.com) with your dynamically assigned IP address. Most broadband Internet Service Providers assign dynamic (changing) IP addresses. When you use a Dynamic DNS service provider, your friends can enter your domain name to connect to your server, no matter what your IP address is.
  • Page 57 Password or Key Enter the password or key provided by your service provider. If the Dynamic DNS provider supplies only a key, enter that key in all three fields. Verify Password or Key Re-type the password or key provided by your service provider. If the Dynamic DNS provider supplies only a key, enter that key in all three fields.

  • Page 58: Status

    Status The Status tab provides the following configuration options: Device Info, Wireless, Routing, Logs, Statistics and Active Sessions. Status_Device info All of your Internet and network connection details are displayed on the Device Info page. The firmware version is also displayed here. Some browsers have limitations that make it impossible to update the WAN status display when the status changes.
  • Page 59 DHCP Connection Click the DHCP Release button to release the router's IP address. The router will not respond to IP messages from the WAN side until you click the DHCP Renew button or power-up the router again. Clicking the DHCP Renew button causes the router to request a new IP address from the ISP's server.
  • Page 60 Signal This is a relative measure of signal quality. The value is expressed as a percentage of theoretical best quality. Signal quality can be reduced by distance, by interference from other radio-frequency sources (such as cordless telephones or neighboring wireless networks), and by obstacles between the router and the wireless device.
  • Page 61 Status_Logs The router automatically logs (records) events of possible interest in its internal memory. If there is not enough internal memory for all events, logs of older events are deleted, but logs of the latest events are retained. The Logs option allows you to view the router logs. You can define what types of events you want to view and the level of events to view.
  • Page 62 Apply Log Settings Now Click this button after changing Log Options to make them effective and permanent. Refresh Clicking this button refreshes the display of log entries. There may be new events since the last time you accessed the log. Clear Clicking this button erases all log entries.
  • Page 63 Sent The number of packets sent from the router. Received The number of packets received by the router. TX Packets Dropped The number of packets that were dropped while being sent, due to errors, collisions, or router resource limitations. RX Packets Dropped The number of packets that were dropped while being received, due to errors, collisions, or router resource limitations.
  • Page 64 Protocol The communications protocol used for the conversation. External The IP address and port number of the WAN-side application. The port number of the LAN-side application as viewed by the WAN-side application. Priority The preference given to outbound packets of this conversation by the Traffic Shaping logic. Smaller numbers represent higher priority.

  • Page 65: Glossary

    Glossary Access Control List ACL. This is a database of network devices that are allowed to access resources on the network. Access Point AP. Device that allows wireless clients to connect to it and access the network ActiveX A Microsoft specification for the interaction of software components. Ad-hoc network Peer-to-Peer network between wireless clients Address Resolution Protocol...
  • Page 66 American Standard Code for Information Interchange. This system of characters is most commonly used for text files Attenuation The loss in strength of digital and analog signals. The loss is greater when the signal is being transmitted over long distances. Authentication To provide credentials, like a Password, in order to verify that the person or device is really who they are claiming to be...
  • Page 67 A time during processes when something causes the process to slowdown or stop all together Broadband A wide band of frequencies available for transmitting data Broadcast Transmitting data in all directions at once Browser A program that allows you to access resources on the web and provides them to you graphically Cable modem A device that allows you to connect a computer up to a coaxial cable and receive Internet...
  • Page 68 The second layer of the OSI model. Controls the movement of data on the physical link of a network Database Organizes information so that it can be managed updated, as well as easily accessed by users or applications. DB-25 A 25 ping male connector for attaching External modems or RS-232 serial devices DB-9 A 9 pin connector for RS-232 connections Decibels related to dipole antenna...
  • Page 69 "Demilitarized Zone". A computer that logically sits in a "no-mans land" between the LAN and the WAN. The DMZ computer trades some of the protection of the router's security mechanisms for the convenience of being directly addressable from the Internet. Domain Name System: Translates Domain Names to IP addresses Domain name A name that is associated with an IP address...
  • Page 70 A way of sending data through light impulses over glass or plastic wire or fiber File server A computer on a network that stores data so that the other computers on the network can all access it File sharing Allowing data from computers on a network to be accessed by other computers on the network with different levels of access rights Firewall A device that protects resources of the Local Area Network from unauthorized users outside of...
  • Page 71 A standard that provides consistency of voice and video transmissions and compatibility for videoconferencing devices Half-duplex Data cannot be transmitted and received at the same time Hashing Transforming a string of characters into a shorter string with a predefined length Hexadecimal Characters 0-9 and A-F The action of data packets being transmitted from one router to another...
  • Page 72 Infrastructure In terms of a wireless network, this is when wireless clients use an Access Point to gain access to the network Internet A system of worldwide networks which use TCP/IP to allow for resources to be accessed from computers around the world Internet Explorer A World Wide Web browser created and provided by Microsoft Internet Protocol...
  • Page 73 Java A programming language used to create programs and applets for web pages Kbps Kilobits per second Kbyte Kilobyte Local Area Network Latency The amount of time that it takes a packet to get from the one point to another on a network. Also referred to as delay Light Emitting Diode Legacy...
  • Page 74 MDIX Medium Dependent Interface Crossover, is an Ethernet port for a connection to a crossover cable Management Information Base is a set of objects that can be managed by using SNMP Modem A device that Modulates digital signals from a computer to an analog signal in order to transmit the signal over phone lines.
  • Page 75 Network Time Protocol Used to synchronize the time of all the computers in a network Network Interface Card Network Time Protocol OFDM Orthogonal Frequency-Division Multiplexing is the modulation technique for both 802.11a and 802.11g Open Systems Interconnection is the reference model for how data should travel between two devices on a network OSPF Open Shortest Path First is a routing protocol that is used more than RIP in larger scale...
  • Page 76 Port A logical channel endpoint in a network. A computer might have only one physical channel (its Ethernet channel) but can have multiple ports (logical channels) each identified by a number. Point-to-Point Protocol is used for two computers to communicate with each over a serial interface, like a phone line PPPoE Point-to-Point Protocol over Ethernet is used to connect multiple computers to a remote server...
  • Page 77 RJ-45 The most commonly used connection method for Ethernet RS-232C The interface for serial communication between computers and other related devices Algorithm used for encryption and authentication Server A computer on a network that provides services and resources to other computers on the network Session key An encryption and decryption key that is generated for every communication session between...
  • Page 78 Secure Shell is a command line interface that allows for secure connections to remote computers SSID Service Set Identifier is a name for a wireless network Stateful inspection A feature of a firewall that monitors outgoing and incoming traffic to make sure that only valid responses to outgoing requests are allowed to pass though the firewall Subnet mask Determines what portion of an IP address designates the Network and which part designates...
  • Page 79 Universal Plug and Play A standard that allows network devices to discover each other and configure themselves to be a part of the network Upgrade To install a more recent version of a software or firmware product Upload To send a request from one computer to another and have a file transmitted from the requesting computer to the other UPnP Universal Plug and Play...
  • Page 80 Windows Connect Now. A Microsoft method for configuring and bootstrapping wireless networking hardware (access points) and wireless clients, including PCs and other devices. Wireless Distribution System. A system that enables the interconnection of access points wirelessly. Web browser A utility that allows you to view content and interact with all of the information on the World Wide Web Wired Equivalent Privacy is security for wireless networks that is supposed to be comparable to that of a wired network...

  • Page 81: Limited Warranty

    Limited Warranty TRENDware warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. Wireless Products – 3 Years Warranty If a product does not operate as warranted above during the applicable warranty period, TRENDware shall, at its option and expense, repair the defective product or part, deliver to customer an equivalent product or part to replace the defective item, or refund to customer the purchase price paid for the defective product.
  • Page 82 LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDWARE ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR...

Table of Contents