Advertisement

Quick Links

R18XBCT10

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the R18XBCT10 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Ryobi R18XBCT10

  • Page 1 R18XBCT10...
  • Page 2: Intended Use

    cord away from heat, oil, sharp edges or moving IMPORTANT! parts. Damaged or entangled cords increase the risk of It is essential that you read the instructions in this manual electric shock. before assembling, operating, and maintaining the ■ When operating a power tool outdoors, use an product.
  • Page 3 ■ Store idle power tools out of the reach of children ■ Never service damaged battery packs. Service and do not allow persons unfamiliar with the power of battery packs should only be performed by the tool or these instructions to operate the power tool. manufacturer or authorized service providers.
  • Page 4: Additional Safety Warnings

    ■ Keep all parts of the body away from the cutter, line and take corrective actions to eliminate the cause of or blade when the machine is operating. Before you blade binding. start the machine, make sure the cutter, line or blade ■...
  • Page 5: Transportation And Storage

    ■ Always ensure that ventilation openings are kept clear ■ Follow all special requirements on packaging and of debris. Blocked air inlets and debris may result in labelling when transporting batteries by a third party. overheating or risk of fire. Ensure that no batteries can come in contact with other batteries or conductive materials while in transport by ■...
  • Page 6: Symbols In This Manual

    The TRI-ARC blade is appropriate for the product and is suited for cutting pulpy weeds and vines. Beware of thrown or flying objects. Keep all bystanders, especially children and pets, at least 15 m away from the operating area. Remove the battery pack before starting any work on the product.
  • Page 7 R18XBCT10 Speed selector Lock-out trigger On/Off trigger Powerhead Rear handle Harness hanger Knob Upper drive shaft Front handle Handle lock Hanger cap Lower drive shaft Grass deflector TRI-ARC blade Blade protector Construction washer Flange washer Harness Combination wrench Operator's manual...
  • Page 8 Always wear safety goggles or safety Push the lock button and remove the Insert the lower drive shaft into the glasses with side shields when hanger cap from the lower drive shaft. upper drive shaft until the lock button clicks into place. Tighten the knob to operating the product.
  • Page 9 Remove the handle lock from the Install the front handle to the upper Turn the screw in the handle lock front handle by turning the screw drive shaft at a preferred position. Re- clockwise to secure the front handle in counterclockwise.
  • Page 10 Operating the p.11 product Cleaning the p.13 Storing the product p.14 product...
  • Page 11: Operating The Product

    OPERATING THE PRODUCT WARNING: For safety reasons, the product must be adequately controlled by a two- handed operation. Hold the product with the right hand on the rear handle and the left hand on the front handle. WARNING: Exercise extreme caution when using the product.
  • Page 12 3. Use the product to cut long grass, pulpy weed, and similar vegetation at or about ground level. NOTE: Beware of blade thrust. NOTE: Cut tall grass from the top down. This prevents grass from wrapping around the shaft housing and bump head, which may cause damage from overheating.
  • Page 13: Cleaning The Product

    CLEANING THE PRODUCT 1. Remove the battery pack. 2. Place the product on a level surface. Position the product with the motor side down and the grass deflector side up. WARNING: Exercise extreme caution when using the product. Keep hands and feet away from the cutting means at all times, especially when turning on the motor.
  • Page 14: Storing The Product

    STORING THE PRODUCT WARNING: Clean the product before storing. 1. Remove the battery pack. 2. Install the blade guard. 3. Store the product in a cool, dry, and well-ventilated place that is inaccessible to children and away from sources of ignition. Do not store the product outdoors.
  • Page 15: Product Specifications

    Cordless brushcutter standardised test and may be used to compare one tool with Model R18XBCT10 another. They may be used for a preliminary assessment of exposure. Voltage 18 V d.c.
  • Page 16 Techtronic Industries N.Z. Limited Unit C, 70 Business Parade South, Highbrook, Auckland 2013, New Zealand RYOBI is a trade mark of Ryobi Limited, and is used under license. TRI-ARC is a trade mark of Techtronic Outdoor Products Technology Limited. 961479099-01...

Table of Contents