Toshiba MJ-6101 Service Manual

Hole punch unit

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

SERVICE MANUAL

HOLE PUNCH UNIT

MJ-6101/6103/6104/6105/6106

File No. SME050022I0

R05092196004-TTEC

Ver09 F_2017-04

Table of Contents

Need help?

Do you have a question about the MJ-6101 and is the answer not in the manual?

Questions and answers

Summary of Contents for Toshiba MJ-6101

Page 1 SERVICE MANUAL HOLE PUNCH UNIT MJ-6101/6103/6104/6105/6106 File No. SME050022I0 R05092196004-TTEC Ver09 F_2017-04...
Page 2 Other company names and product names in this manual are the trademarks of their respective companies. © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved Under the copyright laws, this manual cannot be reproduced in any form without prior written permission of TOSHIBA TEC CORPORATION.
Page 3 Before using the wrist band, pull out the power cord plug of the equipment and make sure that there is no uninsulated charged objects in the vicinity. 16)For the recovery and disposal of used MJ-6101/6103/6104, consumable parts and packing materi- als, follow the relevant local regulations/rules.
Page 4 17)After completing installation, servicing and maintenance of the MJ-6101/6103, return the MJ-6101/ 6103/6104 to its original state, and check operation. 18)When you move the finisher, do not move it in the direction of the arrow as shown in the figure below otherwise it might topple over.
Page 5: Table Of Contents
7. MAINTENANCE ......................7-1 7.1 Maintenance and Inspection Points..................7-1 7.2 Firmware Update ......................... 7-2 7.2.1 MJ-6101/6103 (Firmware updating with download jig) ..........7-2 7.2.2 MJ-6104/6105/6106 (Firmware updating with USB device) ........7-4 8. ELECTRIC CIRCUIT ..................... 8-1 8.1 Harness Diagram......................... 8-1 8.1.1 MJ-6101/MJ-6103 ....................
Page 6 8.3 PC Board ........................... 8-21 8.3.1 MJ-6101/MJ-6103 ....................8-21 8.3.2 MJ-6104/6105/6106 ....................8-23 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved CONTENTS...
Page 7: Specifications
MJ-6101/6103/6104/6105/6106E:  6.5 mm (0.256 in.) MJ-6101/6103/6104/6105/6106N:  8.0 mm (0.315 in.) MJ-6101/6103/6104/6105/6106F:  6.5 mm (0.256 in.) MJ-6101/6103/6104/6105/6106S:  6.5 mm (0.256 in.) © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 SPECIFICATIONS 1 - 1 17/03...
Page 8 The width of the entrance guide is also MJ-6103 : DEEP VIOLET GRAY different between MJ-6101 and MJ- MJ-6104 : FAIR WHITE 6103/MJ-6104. MJ-6105/6106 : JET BLACK MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved SPECIFICATIONS 1 - 2 16/06...
Page 9 3.15±0.04in. 80±1 mm / 3.15±0.04in. 12±3 mm / 12±3 mm / 0.4±0.12in. 0.4±0.12in. [ 2 ] 2-Hole / 3-Hole ( MJ-6101/6103/6104/6105/6106N ) [ 4 ] 4-Hole ( MJ-6101/6103/6104/6105/6106S ) X±3 mm / X±3 mm / X±0.12in. X±0.12in. 21±1 mm / 70±1 mm /...
Page 11: General Description
GENERAL DESCRIPTION Main Components Rear cover Front cover Jam release knob Punched scrap box Fig. 2-1 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 GENERAL DESCRIPTION 2 - 1...
Page 12: Sectional View
Skew sensor (SEN) Skew sensor (LED) Sideways adjustment motor Punched scrap full sensor (LED) Hole punch control PC board (PNC board) Front cover sensor MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved GENERAL DESCRIPTION 2 - 2...
Page 13: Electric Parts Layout
Electric Parts Layout S7-2 S6-2 S8-2 S7-1 S6-1 S8-1 S7-1 S7-2 Fig. 2-3 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 GENERAL DESCRIPTION 2 - 3...
Page 14: Symbols And Functions Of Various Components
Detects the punched scrap full state.(Light 1-24 sensing part) 3) PC board Symbol Name Function Remarks Hole punch control PC board (PNC Controls the hole punch unit. 2-14 board) MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved GENERAL DESCRIPTION 2 - 4...
Page 15: Diagram Of Signal Blocks
Paper position sensor ( LED ) ( S6-1 ) drive Skew sensor ( LED ) ( S7-1 ) circuit Punched scrap full sensor ( LED ) ( S8-1 ) Fig. 2-5 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 GENERAL DESCRIPTION 2 - 5 12/12...
Page 16: Mj-6105/6106
Paper position sensor ( LED ) ( S6-1 ) drive Skew sensor ( LED ) ( S7-1 ) circuit Punched scrap full sensor ( LED ) ( S8-1 ) Fig. 2-6 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved GENERAL DESCRIPTION 2 - 6 16/06...
Page 17: Description Of Interface Signals
Data communication (RxD and TxD) between the hole punch unit and the Finisher has adopted the serial communication system which does not allow checking whether the signals are transmitted/ received properly using testing devices in the field. © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 GENERAL DESCRIPTION...
Page 18: Mj-6105/6106
TRMT-STEP Finisher Hole punch unit TRMT-CUR ( CN7 ) ( CN1 ) TRMT-MD0 TRMT-MD1 Fig. 2-9 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved GENERAL DESCRIPTION 2 - 8 16/06...
Page 19: Description Of Operations
The unit does not detect paper jams. Instead, the unit transmits an error signal to the Finisher only when the unit has detected abnormality in its motors or sensors. © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106...
Page 20: Punching Position Alignment Operation
The adjustable range of skew is ±0.6 degrees. The adjustment requires approx. 0.15 seconds. Skew home position sensor Punching unit Skew adjustment motor Skew sensor ( SEN ) Skew sensor ( LED ) Fig. 3-1 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved DESCRIPTION OF OPERATIONS 3 - 2...
Page 21: Sideways Deviation Adjustment
Punching unit Paper position sensor ( SEN ) Paper position sensor ( LED ) Sideways deviation Sideways adjustment motor home position sensor Fig. 3-2 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 DESCRIPTION OF OPERATIONS 3 - 3...
Page 22: Punching Operation
The combinations of these positions and light sta- tus are shown below. Punch home position sensor (S4) Punching sensor (S5) Position 1 Transmit Shut off Position 2 Transmit Transmit MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved DESCRIPTION OF OPERATIONS 3 - 4...
Page 23 6104/6105/6106S 4 holes (Sweden) As for the MJ-6101/6103/6104/6105/6106E/N/F, the punch motor (M3) rotates in a normal direction or in a reverse direction so that their actuators reciprocate between the positions 1 and 2. Paper is thus punched out at the timing along with this reciprocating movement. Namely, 1 punching operation is per- formed when the actuator has gone half round.
Page 24 • MJ-6101/6103/6104/6105/6106N Reverse Normal rotation rotation Fig. 3-5 • MJ-6101/6103/6104/6105/6106F Reverse Normal rotation rotation Fig. 3-6 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved DESCRIPTION OF OPERATIONS 3 - 6 16/06...
Page 26: Transport Operation
High speed Low speed Transport roller Transport roller Gear Gear Transport motor Transport motor Fig. 3-8 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved DESCRIPTION OF OPERATIONS 3 - 8...
Page 29: Disassembly And Assembly
Front lower cover Fig. 4-1 [B] Rear lower cover Release 2 latches and take off the rear lower cover. Rear lower cover Fig. 4-2 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 DISASSEMBLY AND ASSEMBLY 4 - 1 06/04...
Page 30 Open the front cover. Pull out the knob. Knob Fig. 4-4 Remove 3 screws and take off the front cover. Front cover Fig. 4-5 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved DISASSEMBLY AND ASSEMBLY 4 - 2 06/04...
Page 31 [F] Right cover Remove 2 screws. Slide the right cover upward and take it out toward the lower right. Right cover Fig. 4-8 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 DISASSEMBLY AND ASSEMBLY 4 - 3...
Page 32: Motor
Disconnect 1 connector. Release the har- nesses from 3 clamps. Fig. 4-9 Remove 2 screws and take off the skew adjustment motor. Skew adjustment motor Fig. 4-10 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved DISASSEMBLY AND ASSEMBLY 4 - 4...
Page 33 Disconnect 1 connector. Remove 2 screws and take off the sideways adjustment motor. MJ-6101/MJ6103 Sideways adjustment motor Fig. 4-12 MJ-6104/MJ-6105/MJ-6106 Sideways adjustment motor Fig. 4-13 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 DISASSEMBLY AND ASSEMBLY 4 - 5 16/06...
Page 34 Take off the rear cover.  P. 4-2 "[C] Rear cover" Remove 4 screws and take off the circuit board bracket. Circuit board bracket Fig. 4-16 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved DISASSEMBLY AND ASSEMBLY 4 - 6 16/06...
Page 35 2 bushings, 1 motor damper Transport motor and take off the transport motor. Bushing Screw damper Motor damper Bushing Screw damper Fig. 4-18 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 DISASSEMBLY AND ASSEMBLY 4 - 7...
Page 36: Punching Unit
Disconnect 4 connectors from the hole punch control PC board. Fig. 4-19 MJ-6104/MJ-6105/MJ-6106 Fig. 4-20 Remove 2 springs. Spring Spring Fig. 4-21 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved DISASSEMBLY AND ASSEMBLY 4 - 8 16/06...
Page 38: Sensor/Switch
 P. 4-2 "[D] Front cover" Take off the upper cover.  P. 4-3 "[E] Upper cover" Rotate the actuator. Fig. 4-25 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved DISASSEMBLY AND ASSEMBLY 4 - 10 06/04...
Page 39  P. 4-3 "[E] Upper cover" Rotate the actuator so that it does not con- tact the punch home position sensor. Fig. 4-28 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 DISASSEMBLY AND ASSEMBLY 4 - 11...
Page 40 Rotate the actuator so that it does not con- tact the punch sensor. Fig. 4-30 Disconnect 1 connector. Release the latch and take off the punch sensor. Punching sensor Fig. 4-31 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved DISASSEMBLY AND ASSEMBLY 4 - 12...
Page 41 Disconnect 1 connector and remove 1 screw from the lower entrance guide to take off Skew sensor ( LED ) each skew sensor (LED). Lower entrance guides Fig. 4-34 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 DISASSEMBLY AND ASSEMBLY 4 - 13...
Page 42 Paper position sensor ( LED ) Disconnect 1 connector, remove 1 screw, and take off each paper position sensor (light emitting) from the punching unit. Fig. 4-36 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved DISASSEMBLY AND ASSEMBLY 4 - 14 07/03...
Page 43 Disconnect 1 connector, remove 1 screw, and take off each punched scrap full sensor (LED). Punched scrap full sensor ( LED ) Fig. 4-38 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 DISASSEMBLY AND ASSEMBLY 4 - 15 11/04...
Page 44: Board
MJ-6104/MJ-6105/MJ-6106 Fig. 4-40 Remove 4 screws and take off the hole punch control PC board. Hole punch control PC board Fig. 4-41 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved DISASSEMBLY AND ASSEMBLY 4 - 16 16/06...
Page 45: Roller
 P. 4-8 "[A] Punching unit" Transport guides Remove 2 screws and take off both the upper and lower transport guides. Fig. 4-44 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 DISASSEMBLY AND ASSEMBLY 4 - 17 16/06...
Page 46 Remove 1 E-ring and 1 bushing from the front side of the shaft. E-ring Bushing Fig. 4-46 Take off the transport roller. Transport roller Fig. 4-47 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved DISASSEMBLY AND ASSEMBLY 4 - 18...
Page 47: Adjustment
9: +0.66mm 10: +0.88mm 11: +1.10mm If the adjustment values can be confirmed from the pre-change board, check them from the connected equipment and then set them into the post-change board. © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 ADJUSTMENT...
Page 48 Turn the power of the equipment ON. The finisher enters into the stopping position adjustment mode. LED1 on the finisher control panel blinks. The number of times it blinks indicates the current adjustment value. MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved ADJUSTMENT 5 - 2 16/06...
Page 49 Turn the power of the equipment OFF. Turn all the bits of SW1 (DIP-SW) on the finisher control PC board OFF. Install the board access cover of the Finisher. © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 ADJUSTMENT...
Page 51: Troubleshoothing
Is the wiring between the hole punch control PC board (HP) and skew adjustment motor (M1) correct? NO Correct the wiring.  1) Replace the skew adjustment motor (M1). 2) Replace the hole punch control PC board (HP). © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 TROUBLESHOOTHING 6 - 1...
Page 52 Is the wiring between the hole punch control PC board (HP) and sideways adjustment motor (M2) correct? NO Correct the wiring.  1) Replace the punch sideways adjustment motor (M2). 2) Replace the hole punch control PC board (HP). MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved TROUBLESHOOTHING 6 - 2...
Page 53 Is the wiring between the hole punch control PC board (HP) and skew adjustment motor (M1) correct? NO Correct the wiring.  1) Replace the skew adjustment motor (M1). 2) Replace the hole punch control PC board (HP). © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 TROUBLESHOOTHING 6 - 3...
Page 54 Is the conductor pattern on the hole punch control PC board (HP) open circuited or short cir- cuited? YES Replace the hole punch control PC board (HP).  Replace the finisher control PC board. MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved TROUBLESHOOTHING 6 - 4...
Page 55 Is the conductor pattern on the hole punch control PC board (HP) open circuited or short cir- cuited? YES Replace the hole punch control PC board (HP).  Replace the finisher control PC board. © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 TROUBLESHOOTHING 6 - 5...
Page 57: Maintenance
*3: Page-Item (P-I) is described in the column of the Parts list. *4: This unit may require replacement once or more over the period of machine warranty because of deterioration or damage. Replace them as needed. © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 MAINTENANCE...
Page 58: Firmware Update
Attach the ROM to the download jig. Make sure that the ROM and its direction are correct. Connector Mark for ROM installation direction Fig. 7-2 Turn OFF the power of the equipment. MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MAINTENANCE 7 - 2 12/12...
Page 59 Connect the download jig with the jig connector (CN9) on the finisher control PC board. Download jig Fig. 7-4 Set the DIP-SW4 on the hole punch control PC board to ON. 1 2 3 4 Fig. 7-5 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 MAINTENANCE 7 - 3 12/12...
Page 60: Mj-6104/6105/6106 (Firmware Updating With Usb Device)
(15) Install the finisher board access cover. 7.2.2 MJ-6104/6105/6106 (Firmware updating with USB device) Refer to "FIRMWARE UPDATING" in the Service Manual for MFP. MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MAINTENANCE 7 - 4 16/06...
Page 61: Electric Circuit
Skew adjustment motor Punched scrap S8-1 Transport motor full sensor ( LED ) Punched scrap S8-1 full sensor ( SEN ) Fig. 8-1 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 ELECTRIC CIRCUIT 8 - 1 12/12...
Page 62: Mj-6104
S7-1 LED-SK1 Skew sensor (LED) S7-1 LED-SK2 PMT-F Punch motor PMT-R S7-2 AN-SK1 P24V Skew sensor (SEN) S7-2 AN-SK2 P24V Fig. 8-2 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved ELECTRIC CIRCUIT 8 - 2 12/12...
Page 63 S7-1 LED-SK1 Skew sensor (LED) S7-1 LED-SK2 PMT-F Punch motor PMT-R S7-2 SNS-SK1 P24VA Skew sensor (SEN) S7-2 SNS-SK2 P24VA Fig. 8-3 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 ELECTRIC CIRCUIT 8 - 3 16/06...
Page 75 10P/CH/1005-3 10P/CH/1005-3 C309 10P/CH/1005-3 R318 30K/C/1005 C311 1000P/CH/1005 NOT MOUNT R317 R327 0`/OT/C/1005 10K/F/C/1005 0`/OT/C/1005 R307 0.1^/B/1005 0.2`1/2W/F/C/3225 R308 0.2`1/2W/F/C/3225 100^35V/CE-10 Fig. 8-15 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 ELECTRIC CIRCUIT 8 - 15 16/06...
Page 76 R349 R359 R361 1.8K1/16W/F/C/1005-1 10K/F/C/1005 1.8K1/16W/F/C/1005-1 10K/F/C/1005 0`/OT/C/1005 0`/OT/C/1005 R337 R346 0.1^/B/1005 0.1^/B/1005 0.2`1/2W/F/C/3225 0.2`1/2W/F/C/3225 R340 R350 0.2`1/2W/F/C/3225 0.2`1/2W/F/C/3225 100^35V/CE-10 100^35V/CE-10 Fig. 8-16 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved ELECTRIC CIRCUIT 8 - 16 16/03...
Page 77 R387 11K/F/C/1005 10K/F/C/1005 0.1^/B/1005 R351 1K/C/1005 470`/C/1005 C330 0.1^/B/1005 2.2K/C/1005 R366 R390 R389 10K/C/1005 6.8K/C/1005 R410 4.7K/C/1005 C334 0.01^/B/1005 R403 10K/C/1005 Fig. 8-17 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 ELECTRIC CIRCUIT 8 - 17 16/03...
Page 78 10K/C/1005 10K/C/1005 10K/C/1005 10K/C/1005 0.1^/B/1005 560`/C/1005 1K/C/1005 1K/C/1005 1K/C/1005 1K/C/1005 1K/C/1005 1K/C/1005 1K/C/1005 560`/C/1005 1K/C/1005 1K/C/1005 1K/C/1005 1K/C/1005 1K/C/1005 1K/C/1005 1K/C/1005 Fig. 8-18 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved ELECTRIC CIRCUIT 8 - 18 16/03...
Page 79 R333 C327 10K/C/1005 1000P/B/1005 R367 R375 13K1/16W/F/C/1005-1 R369 22K/F/C/1005 47K/F/C/1005 100^35V/CE-10 NOT MOUNT NOT MOUNT 100`/C/1005 UDZV/TE/17/30B/C-E R301 10K/C/1005 C301 0.1^/B/1005 Fig. 8-19 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 ELECTRIC CIRCUIT 8 - 19 16/03...
Page 80 NOT MOUNT 0.1^/B/1005 R133 10`/C/1005 0.1^/B/1005 0.1^/B/1005 0.1^/B/1005 0.1^/B/1005 0.1^/B/1005 R134 0.1^/B/1005 10`/C/1005 0.1^/B/1005 0.1^/B/1005 0.1^/B/1005 0.1^/B/1005 1/292161/2 292161/6 292161/5 292161/7 CN10 Fig. 8-20 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved ELECTRIC CIRCUIT 8 - 20 16/03...
Page 81 1) Hole punch control PC board Fig. 8-21 2) Rear side paper position sensor (LED) Fig. 8-22 3) Rear side paper position sensor (SEN) Fig. 8-23 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 ELECTRIC CIRCUIT 8 - 21 12/12...
Page 82 4) Front side paper position sensor (SEN), Skew sensor (SEN), Punched scrap full sensor (SEN) Fig. 8-24 5) Front side paper position sensor (LED), Skew sensor (LED), Punched scrap full sensor (LED) Fig. 8-25 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved ELECTRIC CIRCUIT 8 - 22 12/12...
Page 83 8.3.2 MJ-6104/6105/6106 [A] Hole punch control PC board [A-1] MJ-6104 Fig. 8-26 [A-2] MJ-6105/6106 Fig. 8-27 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 ELECTRIC CIRCUIT 8 - 23 16/06...
Page 84 [D] Front side paper position sensor (SEN), Skew sensor (SEN), Punched scrap full sensor (SEN) Fig. 8-30 [E] Front side paper position sensor (LED), Skew sensor (LED), Punched scrap full sensor (LED) Fig. 8-31 MJ-6101/6103/6104/6105/6106 © 2006 - 2017 TOSHIBA TEC CORPORATION All rights reserved ELECTRIC CIRCUIT 8 - 24 12/12...
Page 85: Revision Record
REVISION RECORD Ver.09 Ver.09<2017.3.28> Page Contents Information for reused paper has been added. © 2011 - 2017 TOSHIBA TEC CORPORATION All rights reserved MJ-6101/6103/6104/6105/6106 REVISION RECORD 17/03...
Page 88 1-11-1, OSAKI, SHINAGAWA-KU, TOKYO, 141-8562, JAPAN...

This manual is also suitable for:

Mj-6103 Mj-6104 Mj-6105 Mj-6106

Toshiba MJ-6101 Service Manual

Quick Links

Need help?

Questions and answers

Summary of Contents for Toshiba MJ-6101

Page 5: Table Of Contents

Page 7: Specifications

Page 11: General Description

Page 12: Sectional View

Page 13: Electric Parts Layout

Page 14: Symbols And Functions Of Various Components

Page 15: Diagram Of Signal Blocks

Page 16: Mj-6105/6106

Page 17: Description Of Interface Signals

Page 18: Mj-6105/6106

Page 19: Description Of Operations

Page 20: Punching Position Alignment Operation

Page 21: Sideways Deviation Adjustment

Page 22: Punching Operation

Page 26: Transport Operation

Page 27: Punched Scrap Detection

Page 29: Disassembly And Assembly

Page 32: Motor

Page 36: Punching Unit

Page 38: Sensor/Switch

Page 44: Board

Page 45: Roller

Page 47: Adjustment

Page 51: Troubleshoothing

Page 57: Maintenance

Page 58: Firmware Update

Page 60: Mj-6104/6105/6106 (Firmware Updating With Usb Device)

Page 61: Electric Circuit

Page 62: Mj-6104

Page 64: Circuit Diagram

Page 70: Mj-6104

Page 85: Revision Record

This manual is also suitable for:

Toshiba MJ-6101 Service Manual

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Toshiba MJ-6101

Summary of Contents for Toshiba MJ-6101

This manual is also suitable for:

Table of Contents