Denon AVR-891 Owner's Manual page 11

ENGLISH
Set up speakers (Audyssey ® Auto Setup)
3
Set up
the remote control unit
n Set up the zone mode
Press ZONE SELECT to switch the
zone mode to "MAIN".
The "MAIN" indicator lights.
Press ZONE SELECT
n Set up the operation mode
AMP
Press to set the remote control
unit to amplifier operation mode.
Press AMP
8
Remote control operation
buttons
STEP 1
Preparation
4
Connect the setup microphone to the
SETUP MIC jack of this unit.
When the setup microphone is
connected, the following screen is
displayed.
AUTO SETUP
AUDYSSEY AUTO SETUP
MultEQ
STEP1 Preparation [1/6]
Connect the speakers
and place them accord-
ing to the recommenda-
tions in the manual.
Set the following
items if necessary.
Amp Assign
Channel Select
Auto Setup Start
ENTER Enter RETURN Cancel
Start Auto Setup
Here, we explain setup using the example of
5.1-channel speaker playback.
For setting other than 5.1-channel surround,
select "Amp Assign" and perform step 3 to 4 of
"Set up speakers" (vpage 34).
If unused channels are set with "Channel Select",
measuring time can be shortened. For setting,
perform steps 5 to 9 of "Set up speakers"
(vpage 35).
5
Use to select "Auto Setup Start"
ui
and then press ENTER .
6
Select "Measure" and then press
ENTER .
When measuring begins, a test tone is
output from each speaker.
• Measuring requires several minutes.
Move the cursor
(Up/Down/Left/Right)
STEP 2
Speaker Detection
7
The detected speakers are displayed.
AUTO SETUP
AUDYSSEY AUTO SETUP MultEQ
STEP2 Spkr Detect Check [2/6]
Front Yes
Center Yes
Subwoofer Yes
Surround Yes
Retry
Next Measurement
ENTER Enter RETURN Cancel
Go to Step 3 (Measurement) after speaker check
NOTE
If a connected speaker is not displayed, the
speaker may not be connected correctly. Check
the speaker connection.
8
Use ui to select "Next
Measurement" and then press ENTER
NOTE
If "Caution" is displayed:
Go to "Error messages" (vpage 10), check
any related items, and perform the necessary
procedures.
If the problem is resolved, return and restart
"Audyssey Auto Setup".
When performing Audyssey Auto
Setup over again
ENTER
Press ui to select "Retry", and then press
When measuring has stopped
RETURN
q Press , to the "Cancel Auto Setup?"
prompt is displayed.
ENTER
o
w Press to select "Yes", then press
Setting up the speakers again
Repeat the operation from step 4 of
STEP 1 Preparation
.
Confirm the setting
STEP 3
Measurement
9
Move the setup microphone to
position 2, use to select
ui
"Measure", and then press
The measurement of the second position
starts. Measurements can be made in up to
six positions.
AUTO SETUP
AUDYSSEY AUTO SETUP MultEQ
STEP3 Measurement
Please place the mic-
rophone at ear height
at 2nd listening
position.
Measure
Next Calculation
ENTER Enter RETURN
Start next measurement. Test Tone will start
1 If you want to omit measurements from the next
position onward, select "Next 1 Calculation".
.
STEP4 Calculation
(Go to )
10
Repeat step 9, measuring positions 3
to 6.
When measurement of position 6 is
completed, a "Measurements finished."
message is displayed.
AUTO SETUP
AUDYSSEY AUTO SETUP
MultEQ
STEP3 Measurement
Measurements finished.
.
Retry
Next Calculation
ENTER Enter RETURN
Proceed to Step 4 (Analyze)
.
Return to previous menu
ENTER .
[3/6]
Cancel
[3/6]
Cancel