Advertisement
Quick Links
HYDRAULIC
LIFTING TABLES
99814 & 99816
These instructions accompanying the product are the original instructions. This document is part of the product,
keep it for the life of the product passing it on to any subsequent holder of the product. Read all these instructions
before assembling, operating or maintaining this product.
This manual has been compiled by Draper Tools describing the purpose for which the product has been designed,
and contains all the necessary information to ensure its correct and safe use. By following all the general safety
instructions contained in this manual, it will ensure both product and operator safety, together with longer life of the
product itself.
All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the
product.
Whilst every effort has been made to ensure the accuracy of information contained in this manual, the Draper Tools
policy of continuous improvement determines the right to make modifications without prior warning.
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Draper HLT-225
Summary of Contents for Draper HLT-225
- Page 1 All photographs and drawings in this manual are supplied by Draper Tools to help illustrate the operation of the product.
-
Page 2: Title Page
Commercial copying, redistribution, hiring or lending is prohibited. No part of this publication may be stored in a retrieval system or transmitted in any other form or means without written permission from Draper Tools Limited. In all cases this copyright notice must remain intact. -
Page 3: Table Of Contents
CONTENTS 2.1 CONTENTS TITLE PAGE 1.1 INTRODUCTION ........................2 1.2 REVISION HISTORY ......................2 1.3 UNDERSTANDING THIS MANUAL’S SAFETY CONTENT ..........2 1.4 COPYRIGHT © NOTICE ......................2 CONTENTS 2.1 CONTENTS ..........................3 WARRANTY 3.1 WARRANTY .........................4 INTRODUCTION 4.1 SCOPE ..........................5 4.2 SPECIFICATION ........................5 4.3 HANDLING AND STORAGE ....................5 HEALTH AND SAFETY INFORMATION 5.1 GENERAL SAFETY INSTRUCTIONS FOR HYDRAULIC LIFTING TABLES .... -
Page 4: Warranty
This warranty applies in lieu of any other warranty expressed or implied and variations of its terms are not authorised. Your Draper warranty is not effective unless you can produce upon request a dated receipt or invoice to verify your proof of purchase within the warranty period. -
Page 5: Introduction
SPECIFICATION Stock No................99814 ..........99816 Part No................HLT-225 .........HLT-300 Capacity (Safe Working Load) ......... 225kg ..........300kg Table dimensions ............705 x 450mm ......820 x 520mm Min table height .............. 225mm .......... 350mm Max table height ............. -
Page 6: Health And Safety Information
HEALTH AND SAFETY INFORMATION GENERAL SAFETY INSTRUCTIONS FOR HYDRAULIC LIFTING TABLES 1) Use a qualified person to maintain the table in good condition. Keep it clean for best and safest performance. 2) DO NOT exceed the rated capacity. 3) Use this table for lifting purpose only. DO NOT use it for any other purpose it is not designed to perform. -
Page 7: Residual Risk
HEALTH AND SAFETY INFORMATION WARNING: The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. -
Page 8: Technical Description
TECHNICAL DESCRIPTION IDENTIFICATION (11) (10) 99814 shown Locking bars (1) Table top Fixed front castor Lowering lever (10) 360° Rear castor (3) Lifting pedal assembly (11) Lifting pedal (4) Rubber mat Base assembly Handle support hole Handle securing bolt – 8 –... -
Page 9: Unpacking And Checking
Lay the contents out and check them against the parts shown below. If any part is damaged or missing, please contact the Draper Help Line (the telephone number appears on the title page) and do not attempt to use the product. -
Page 10: Preparing The Hydraulic Lifting Table
PREPARING THE HYDRAULIC LIFTING TABLE 8.1 ASSEMBLY - FIG.1 - 3 1) The table cart is almost completely assembled when you open it. To complete the assembly refer to the parts listing and drawing supplied. 2) Place the lifting pedal (11) into the lifting pedal (11) assembly (3) using bolt (13). -
Page 11: Operating The Hydraulic Lifting Table
OPERATING THE HYDRAULIC LIFTING TABLE 9.1 OPERATION - FIG.4 - 7 WARNING: Ensure that you read, understand and apply the safety instructions and warnings before use. Failure to heed these instructions may result in property damage and/or personal injury. (10) 1) Before loading and while stationary, lock the 360°... -
Page 12: Maintenance And Troubleshooting
10. MAINTENANCE AND TROUBLESHOOTING 10.1 MAINTENANCE 1) When not in use, the table must be stored in the lowest position in a dry location to minimize ram and piston corrosion. 2) Lubricate each friction point monthly with a good grease. 3) Inspect all joints and bolts periodically. -
Page 13: Explanation Of Symbols
11. EXPLANATION OF SYMBOLS 11.1 EXPLANATION OF SYMBOLS Read the instruction manual. Wear safety glasses. Warning! – 13 –... -
Page 14: Disposal
12. DISPOSAL 12.1 DISPOSAL – At the end of the machine’s working life, or when it can no longer be repaired, ensure that it is disposed of according to national regulations. – Contact your local authority for details of collection schemes in your area. In all circumstances: •... - Page 15 NOTES – 15 –...
- Page 16 YOUR DRAPER STOCKIST MSJB0721 ©Published by Draper Tools Limited. No part of this publication may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, mechanical photocopying, recording or otherwise without prior permission in writing from...
Need help?
Do you have a question about the HLT-225 and is the answer not in the manual?
Questions and answers