Edition Notes The Maverick Storm 1 Beam User Manual includes a description, safety precautions, installation, programming, operation and maintenance instructions for the Maverick Storm 1 Beam as of the release date of this edition. Trademarks Chauvet, Chauvet Professional, the Chauvet logo, Maverick, and Maverick Storm are registered trademarks or trademarks of Chauvet &...
The product has XLR sockets for DMX input and output. • Notice: This control circuit is isolated and belongs to the Class 2 data port. The control circuit has a cumulative leakage current of less than 3.5 mA. Maverick Storm 1 Beam User Manual Rev. 5...
• In the event of a serious operating problem, stop using immediately. If a Chauvet product requires service, contact Chauvet Technical Support. Maverick Storm 1 Beam User Manual Rev. 5...
LEDs, contributing to shorter lifespans if always used at full intensity. The average LED lifespan is 40,000 to 50,000 hours. To extend LED lifespan, maintain proper ventilation around the product, and limit the overall intensity. Maverick Storm 1 Beam User Manual Rev. 5...
SIRIUS HRI 310W source, this powerful beam fixture slices though every other effect. Tightly focused aerials and dual layerable independent prisms create massive visual effects, with frost to fine-tune looks and light distribution. The Maverick Storm 1 Beam works with DMX, Art-Net™, sACN, RDM and Lumenradio CRMX™.
10.12 in 10.43 in 257 mm 265 mm 16.85 in 428 mm 25.91 in 658 mm 19.57 in 497 mm 4.76 in 121 mm 15.28 in 10.04 in 388 mm 255 mm Maverick Storm 1 Beam User Manual Rev. 5...
3. Setup AC Power The Maverick Storm 1 Beam has an auto-ranging power supply and it can work with an input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart.
ACN to transport DMX512 data over IP or any other ACN-compatible network. Connection Diagram Switch or Router Computer/ Controller (running Art-Net™ or sACN protocol) Maverick Storm 1 Beam To other Art-Net™ or sACN devices Maverick Storm 1 Beam User Manual Rev. 5...
Setup USB Software Update The Maverick Storm 1 Beam allows for software updates with a USB device using the built-in USB port. To update the software using a USB flash drive, do the following: 1. Power on the product, and plug the flash drive into the USB port.
When rigging the product onto a truss, use a mounting clamp of appropriate weight capacity. Procedure The Maverick Storm 1 Beam comes with 2 Omega brackets. The user can directly attach mounting clamps (sold separately). Make sure the clamps are capable of supporting the weight of this product. Use at least two mounting points per product.
Setup Lamp Replacement The Maverick Storm 1 Beam is equipped with an OSRAM SIRIUS HRI 310 W lamp. Follow the procedure below to safely change the lamp. Disconnect the product from power before performing this procedure. Procedure 1. Turn the product off and disconnect it from power. Wait at least 15 minutes for the lamp to cool down.
DO NOT touch the lamp without wearing gloves to avoid leaving grease on the bulb or on the contacts that could reduce the lamp’s life. • ALWAYS change the lamp when it has reached its recommended lifespan to avoid the risk of lamp explosion. Maverick Storm 1 Beam User Manual Rev. 5...
<RIGHT> Navigates rightwards through the menu list Battery Powered Display The Maverick Storm 1 Beam has a battery powered display which enables access to the menu when the product is powered off. Press and hold <MENU> until the display activates (approximately 15 seconds).
Operation Menu Map Refer to the Maverick Storm 1 Beam product page on www.chauvetprofessional.com for the latest menu map. Main Level Programming Levels Description Address 001–512 Sets the starting address Manual Manually set IP address IP Mode DHCP Network sets IP address...
Page 18
Auto Test Auto test all functions Pan Fine Tilt Tilt Fine Test P/T Speed Manually control and test all settings Manual Test 0–255 through the control panel Dimmer Dimmer Fine Shutter Cyan Magenta Maverick Storm 1 Beam User Manual Rev. 5...
Page 19
_ _ _ _ _ Shows any errors, or No Error! Information Frequency Pan Fine Tilt Tilt Fine P/T Speed Channel Shows all current values from input 000–255 Information signals Dimmer Shutter Cyan Magenta Yellow Color Maverick Storm 1 Beam User Manual Rev. 5...
Use control configurations to operate the product with a DMX, Art-Net™, or sACN controller. Control Mode The Maverick Storm 1 Beam works with wired DMX, Lumenradio CRMX™, Art-Net™, and sACN control signals. To select which protocol to use: 1. Go to the Settings main level.
054 057 Frost 058 059 Open 060 187 Color wheel indexing 188 219 Color scroll, fast to slow 220 223 Stop 224 255 Reverse color scroll, slow to fast Maverick Storm 1 Beam User Manual Rev. 5...
Page 22
128 189 Prism rotation, fast to slow Prism 1 rotate 190 193 Stop 194 255 Reverse prism rotation, slow to fast 000 004 No function Prism 2 005 255 Prism insert Maverick Storm 1 Beam User Manual Rev. 5...
1. Go to the Settings main level. 2. Select the Backlight Timer option. 3. Select the length of the backlight timer, from 30S (30 seconds), 1M (1 minute), 5M (5 minutes), or ON (always on). Maverick Storm 1 Beam User Manual Rev. 5...
2. Select the Loss of Data option. 3. Select from Hold (holds last signal received) or Close (blacks out fixture). Lamp Settings To access the lamp settings of the Maverick Storm 1 Beam: 1. Go to the Setup main level. 2. Select the Lamp Settings option.
1. Connect the Maverick Storm 1 Beam products to receive the Presets by a DMX daisy chain. 2. Make the Maverick Storm 1 Beam with the Presets to transfer the first in the DMX daisy chain. 3. Power on all of the products.
3. Select NO (to cancel) or YES (to reset the product configuration). Test Mode Auto Test To have the Maverick Storm 1 Beam automatically test all functions one after the other: 1. Go to the Test main level. 2. Select the Auto Test option.
Operation Web Server The Maverick Storm 1 Beam Web Server can be accessed by any computer on the same network as the product. It allows network access to system information, settings such as control setup, manual testing of all functions, firmware updates, and the ability to change the Web Server password.
Replace M fan 1 MFan1 Fan wires have poor connection Check fan wire connection M Fan 2 is damaged Replace M fan 2 MFan2 Fan wires have poor connection Check fan wire connection Maverick Storm 1 Beam User Manual Rev. 5...
Page 30
Replace the pan/tilt driver board Sensor board is damaged Replace the yellow sensor board The magnetic rod of the yellow sensor YELLOW board is dropped or installed upside Check the magnetic rod down Maverick Storm 1 Beam User Manual Rev. 5...
22.1 Hex screws next to back heat pipes Head and arm cover hex screws Vacuum Test Measurements Use the IP Tester from Chauvet Professional to ensure the product has been reassembled correctly by following the information below: Parameters Values Method...
Page 32
This is to prevent undue stress on the tilt locks and limit the amount of off-axis bounce on internal components. Maverick Storm 1 Beam User Manual Rev. 5...
For warranty terms and conditions and return information, please visit our website. For customers in the United States and Mexico: www.chauvetlighting.com/warranty-registration. For customers in the United Kingdom, Republic of Ireland, Belgium, the Netherlands, Luxembourg, France, and Germany: www.chauvetlighting.eu/warranty-registration. Maverick Storm 1 Beam User Manual Rev. 5...
Need help?
Do you have a question about the MAVERICK STORM 1 BEAM and is the answer not in the manual?
Questions and answers