Advertisement
Quick Links
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Brunner A-Bench
Summary of Contents for Brunner A-Bench
- Page 1 A-Bench Assembly instructions Design: jehs+laub...
- Page 3 And yet the A-Bench is pared down to the essentials even when it comes to the assembly process. Just grab a power screwdriver, some Allen keys and a rubber hammer and you'll be all set to install each of the individual components.
-
Page 4: Table Of Contents
CONTENTS Notes for assembly General notes for setup Overview Overview of components – legs Overview of components – connectors and beams Overview of seat elements Overview of configurations Upholstery element fittings Assembly Connecting the aluminium profiles Installing the 9790-TRR radius beam Installing the 9790-TRE corner beam Installing the frame Preparing the upholstery elements... -
Page 5: Notes For Assembly
NOTES FOR ASSEMBLY General notes for setup The assembly instructions provide general guidelines for assembling your A-bench. · The described workflows are to be observed for all designs. · The assembly tools suggested are simply recommendations from Brunner GmbH. · Only the materials supplied may be used for assembly. -
Page 6: Overview Of Components - Legs
OVERVIEW OF COMPONENTS – LEGS 9790-FAL1 9790-FAL2 Aluminium outer leg Aluminium connecting leg 9790-FEI1 9790-FEI2 Oak outer leg Oak connecting leg... -
Page 7: Overview Of Components - Connectors And Beams
OVERVIEW OF COMPONENTS – CONNECTORS AND BEAMS Länge /length 9790-connector 90° 9790-connector 22.5° Aluminium outer leg Aluminium connecting leg Länge /length Length Länge /length Overview of beams Length (mm) 9790-TR20 Two-seater 1180 9790-TR30 Three-seater 1828 9790-TRE 90° corner 9790-TRR Radius 1 9790-TRR Radius 2 6 . -
Page 8: Overview Of Seat Elements
OVERVIEW OF SEAT ELEMENTS 9790-KG 9790-SG 9790-SAL 9790-SAR 9790-SE 9790-KR 9790-SRI 9790-SRA 9790-T01 9790-T02 9790-T03... -
Page 9: Overview Of Configurations
OVERVIEW OF CONFIGURATIONS 8 . 9 Overview... -
Page 10: Upholstery Element Fittings
UPHOLSTERY ELEMENT FITTINGS Upholstery element fittings Set of four per element Wood screw, 5x25 AW20 (Würth) Black Screw, M6x25 Hex bolt size 5 Black, galvanised Slot nut Black, plastic... -
Page 11: Assembly
CONNECTING THE ALUMINIUM PROFILES Connecting the aluminium profiles to the aluminium cast parts (applies to all connections) Connect the components together. Make sure that there are no gaps. Unscrew the screws from the cast part. This will leave the cast part interlocked in the aluminium profile. Make sure you follow the order of the screws (1 to 4). -
Page 12: Installing The 9790-Trr Radius Beam
INSTALLING THE 9790-TRR RADIUS BEAM 9790-connector 22.5° 16 x Torx T30 8 Nm... -
Page 13: Installing The 9790-Tre Corner Beam
INSTALLING THE 9790-TRE CORNER BEAM 9790-connector 90° Torx T30 8 Nm Assembly 12 . 13... -
Page 14: Installing The Frame
INSTALLING THE FRAME Connect the base. Screw the components together as instructed. Torx T30 8 Nm... -
Page 15: Preparing The Upholstery Elements
PREPARING THE UPHOLSTERY ELEMENTS Fit the slot nuts on the upholstery elements. For each seat hex bolts Do not tighten the screws yet! Assembly 14 . 15... - Page 16 FASTENING THE UPHOLSTERY ELEMENTS 1 Place the upholstery element at the front of the base. Slot nut Aluminium profile Push the upholstery element back. Slot nut Aluminium profile...
- Page 17 FASTENING THE UPHOLSTERY ELEMENTS 2 Fit the slot nuts at the back. For each seat hex bolts Do not tighten the screws yet! Assembly 16 . 17...
- Page 18 ALIGNING THE UPHOLSTERY ELEMENTS Repeat assembly steps 3 to 6 for all of the upholstery elements. Align the upholstery elements.
-
Page 19: Fastening The Upholstery Elements
FASTENING THE UPHOLSTERY ELEMENTS Ensure that the slot nuts are lined up correctly and tighten the screws. ✔ ✘ For each seat IMPORTANT: The slot nuts must be pushed fully into hex bolts the profile before the screws are used to 8 Nm connect the components. - Page 20 FIXING THE UPHOLSTERY ELEMENTS Use four wood screws for each seat element (protection to stop movement) For each seat AW20 8 Nm...
-
Page 21: Installing The Table Tops
INSTALLING THE TABLE TOPS 9790-T01 9790-T02 9790-T03 Fit the slot nuts on the table tops. For each table hex bolts Do not tighten the screws yet! Follow the assembly instructions for the upholstery elements to finish installing the table tops. Assembly 20 . -
Page 22: Installing The Writing Tablet 1
INSTALLING THE WRITING TABLET 1 Carefully insert the writing tablet between two upholstery elements and push it back to the beam. - Page 23 INSTALLING THE WRITING TABLET 2 Fasten the writing tablet to the upholstery elements using the eight screws provided. For each tablet AW20 8 Nm Assembly 22 . 23...
-
Page 24: Installing The Electrification Box
INSTALLING THE ELECTRIFICATION BOX Position the electrification box approximately 40 mm away from the outer edge of the chosen Approx. 40 mm upholstery element. Fasten the electrification box in place using the four screws provided and a power screwdriver. Electrification box AW20 8 Nm... -
Page 25: Care Instructions
CARE INSTRUCTIONS Careful and proper cleaning of the surfaces of your A-Bench is particularly important to keep it in optimum condition for as long as possible. The following cleaning instructions are only intended as a recommendation. Brunner GmbH will not be held liable for damage to the finish caused by improper cleaning. -
Page 26: Cleaning Table Tops
Cleaning table tops with Brunner NanoTec (NTB) surface Brunner NTB should be cleaned regularly but does not require any special care. The material is particularly easy to clean with a damp cloth. A microfibre cloth dampened with detergent and water or glass cleaner is particularly well suited to this. - Page 27 Product design: price list. We reserve the right to technical changes, errors and jehs+laub colour deviations. Illustrations: Claas Ratjen . Brunner GmbH Text: Claas Ratjen . Elena Sauer . Brunner GmbH Design: Wolfgang Merkle . Darmstadt 26 . 27 Care instructions...
- Page 28 © Brunner GmbH 2019 . Im Salmenkopf 10 . 77866 Rheinau, Germany T. +49 78 44 40 20 . F. +49 78 44 40 28 00 . info@brunner-group.com...
Need help?
Do you have a question about the A-Bench and is the answer not in the manual?
Questions and answers