Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Brunner banc
Summary of Contents for Brunner banc
- Page 1 Assembly instructions Design: jehs+laub...
- Page 2 The upholstery elements then simply have to be fitted to the bases with brackets. There is a suitable connector for every lounge landscape. The assembly instructions below show you all relevant components and will help you to assemble your banc lounge system with ease.
-
Page 3: Table Of Contents
Connection of two lounge elements across a corner Adding the bar counter Electrics and cabling Additional information General information about assembly Assembly tool for the modular banc lounge system Care instructions – powder-coated bases Care instructions – cover materials and leather Note Imprint... -
Page 4: Elements Of The Modular Lounge System
ELEMENTS OF THE MODULAR LOUNGE SYSTEM Table and upholstery elements BC-H00 BC-H40 BC-H70 BC-H100 BC-T00 BC-H40E BC-H70E BC-H100E Bases BC-100 BC-200 BC-300... -
Page 5: Configuration Examples
CONFIGURATION EXAMPLES Configurations of the lounge elements Elements of the modular lounge system | Configuration examples 4 . 5... -
Page 6: Assembly Of A Lounge Element
ASSEMBLY OF A LOUNGE ELEMENT FITTING THE GLIDERS Included in scope of delivery: 2x side section 4x glider... -
Page 7: Fitting The Bases
ASSEMBLY OF A LOUNGE ELEMENT FITTING THE BASES Included in scope of delivery: 2x cross beam 2x side section 8x M8x16 Frame sizes: BC-100 BC-200 BC-300 Assembly of a lounge element 6 . 7... -
Page 8: Fitting The Seat Upholstery
ASSEMBLY OF A LOUNGE ELEMENT FITTING THE SEAT UPHOLSTERY Included in scope of delivery: 4x/8x/12x retaining bracket 1x/2x/3x upholstery 4x/8x/12x M8x25 Position of frame sizes: 95 95 BC-100 BC-200 BC-300 Do not fully tighten screw... -
Page 9: Connecting The Seat Upholstery
ASSEMBLY OF A LOUNGE ELEMENT CONNECTING THE SEAT UPHOLSTERY Included in scope of delivery: 1x/2x connector fi tting 8x/16x Spax 4.5x25 Position per frame size: BC-200 BC-300 10 mm spacing Middle of upholstery 90° Screw on connector fi tting with 10 mm spacing between the plastic parts 2 mm spacing Pull upholstery together... -
Page 10: Fitting A Supporting Plate
ASSEMBLY OF A LOUNGE ELEMENT FITTING A SUPPORTING PLATE Included in scope of delivery: 4x shim/plate 4x M6x16/plate 4x retaining bracket/plate 1x supporting plate Screw supporting plate on to base Screw on connector fi tting... -
Page 11: Fitting The Cabin/Fitting The Bases
ASSEMBLY OF A LOUNGE ELEMENT FITTING THE CABIN/FITTING THE BASES Included in scope of delivery: 4x cross beam 2x side section 700 1x side section 2300 16x M8x16 BC 2100 BC 3100/3200 The gliders and base are assembled in the same way as for the individual lounge element, see page 6-7 Assembly of a lounge element 10 . -
Page 12: Fitting The Cabin Seat Upholstery
ASSEMBLY OF A LOUNGE ELEMENT FITTING THE CABIN SEAT UPHOLSTERY Included in scope of delivery: 16x/24x retaining bracket 16x/24x M8x25 4x M6x25 2x/4x corner upholstery 2x/4x upholstery 1x partition 4x shim 1x strip Fit base Screw on corner upholstery (do not tighten screws) - Page 13 ASSEMBLY OF A LOUNGE ELEMENT DETAIL A Slide together and screw on second corner upholstery Guide pin into hole Screw on partition (do not tighten screws) Screw on strip Align upholstery to base Screw on remaining upholstery and screw on (do not tighten screws) Assembly of a lounge element 12 .
-
Page 14: Connecting The Cabin Seat Upholstery
ASSEMBLY OF A LOUNGE ELEMENT CONNECTING THE CABIN SEAT UPHOLSTERY Included in scope of delivery: 2x/4x connector fi tting 16x/32x Spax 4.5x25 Align and connect upholstery and tighten screws, see page 8-10... -
Page 15: Connecting Several Lounge Elements
CONNECTING SEVERAL LOUNGE ELEMENTS LINEAR CONNECTION OF TWO LOUNGE ELEMENTS Included in scope of delivery: 1x shim 1x M8x25 1x M8 nut Side sections are supplied pre-drilled and have to be placed on the correct side during assembly Position lounge elements in linear fashion and screw together Assembly of a lounge element | Connecting several lounge elements 14 . -
Page 16: Connection Of Two Lounge Elements Back To Back
CONNECTING SEVERAL LOUNGE ELEMENTS CONNECTION OF TWO LOUNGE ELEMENTS BACK TO BACK Included in scope of delivery: 2x fastener 4x M8x12 4x M8 sliding block Fit sliding block Position lounge elements back to back and screw both fasteners on to cross beam near side section... -
Page 17: Connection Of Two Lounge Elements Across A Corner
CONNECTING SEVERAL LOUNGE ELEMENTS CONNECTION OF TWO LOUNGE ELEMENTS ACROSS A CORNER Included in scope of delivery: 1x corner connector 2x M8x25 2x sliding block 2x M8x12 Fit sliding block Screw corner connector to cross beam Position lounge elements across corner and Side section is supplied pre-drilled and has to screw corner connector on to side section be placed on the correct side during assembly... -
Page 18: Adding The Bar Counter
ADDING THE BAR COUNTER FITTING THE BAR COUNTER Included in scope of delivery: 1x BC-T02 / BC-T03 4x/5x clothes hook 1x banc with 2 upholstery sections/3 upholstery sections Slide bar element on to threaded pins Screw on clothes hook Screw clothes hook tight... - Page 19 ADDING THE BAR COUNTER FITTING THE BAR COUNTER Included in scope of delivery: 4x shim 4x M5x10 Screw bar element on to base Adding the bar counter 18 . 19...
-
Page 20: Electrics And Cabling
ELECTRICS AND CABLING FITTING THE PROFILE BOX UNDER THE SEAT UPHOLSTERY Included in scope of delivery: 1x profi le box 2x plastic cover 2x M8x12 2x assembly sheet 1x bracket 2x sliding block 2x shim 1x adhesive tape 1x cable duct Screw the profi le box on to the appropriate bracket. -
Page 21: Additional Information
ADDITIONAL INFORMATION GENERAL INFORMATION ABOUT ASSEMBLY The assembly instructions provide general guidelines for assembling your banc lounge system · The steps described should be observed for all modular lounge elements · The assembly tools suggested are simply recommendations from Brunner GmbH ·... -
Page 22: Note
We reserve the right to technical changes, errors and colour variations. Some models are displayed as special versions that are subject to additional costs. Imprint Product design: jehs+laub Illustrations: Patrice Mutschler. Brunner GmbH Hanne Haaf. Brunner GmbH Text: Hanne Haaf. Brunner GmbH Design: Kerstin Lamprecht. Brunner GmbH... - Page 24 © Brunner GmbH 2015 . Im Salmenkopf 10 . D-77866 Rheinau, Germany Phone +49 78 44. 40 20 . Fax +49 78 44. 40 28 0 . info@brunner-group.com...