Subscribe to Our Youtube Channel
Related Manuals for SCHUNK BSWS-M
Summary of Contents for SCHUNK BSWS-M
- Page 1 Assembly and Operating Manual BSWS-M Jaw quick-change system Translation of Original Operating Manual...
- Page 2 Imprint Imprint Copyright: This manual is protected by copyright. The author is SCHUNK SE & Co. KG. All rights reserved. Technical changes: We reserve the right to make alterations for the purpose of technical improvement. Document number: 1580961 Version: 05.00 | 01/02/2024 | en...
-
Page 3: Table Of Contents
5.2.2 Assembling the top jaw on the gripper ........... 20 5.3 Assembly of the kit for customer-specific top jaws ........21 5.3.1 Notes on producing customer-specific top jaws ........ 21 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... - Page 4 6.4 Maintenance of quick-change jaw system without additional height ..... 26 6.4.1 Disassembling the top jaw ............26 6.4.2 Servicing and assembling the top jaw..........26 6.5 Maintenance of the kit for customer-specific top jaws ........ 26 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961...
-
Page 5: General
Non-observance can cause minor injuries. CAUTION Material damage! Information about avoiding material damage. 1.1.2 Definition of Terms The term "product" replaces the product name on the title page in this manual. 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 6: Applicable Documents
Observe the specified maintenance and lubrication intervals Observe the ambient conditions and operating conditions Parts touching the workpiece and wear parts are not included in the warranty. 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 7: Scope Of Delivery
1.4 Accessories For the kit for customer-specific top jaws: Adapter BSWS-AR For information regarding which accessory articles can be used with the corresponding product variants, see catalog data sheet. 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 8: Basic Safety Notes
Use of unauthorized spare parts Using unauthorized spare parts can endanger personnel and damage the product or cause it to malfunction. Use only original spare parts or spares authorized by SCHUNK. 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 9: Gripper Fingers
Wear heat-resistant protective gloves when handling hot surfaces. Wear protective gloves and safety goggles when handling hazardous substances. Wear close-fitting protective clothing and also wear long hair in a hairnet when dealing with moving components. 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 10: Fundamental Dangers
Falling and violently ejected components can cause serious injuries and even death. Take appropriate protective measures to secure the danger zone. Never step into the danger zone during operation. 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 11: Technical Data
Ambient conditions and operating conditions Ambient temperature [°C] min. max. +130 Protection class IP More technical data is included in the catalog data sheet. Whichever is the latest version. 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 12: Design And Description
The jaw quick-change system consists of two adapters (BSWS-A) and a base with a changing system (BSWS-BM) per base jaw on the gripper, [/ 7]. } 1.3 NOTE The base (BSWS-BM) cannot be combined with the adapters (BSWS-AR). 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 13: Jaw Quick-Change System Without Additional Height (Bsws-Ar With Bsws-Abrm)
(BSWS-ABRM) per base jaw on the gripper, } 1.3 [/ 7]. NOTE The top jaw with changing system made of aluminum (BSWS- ABRM) cannot be combined with the adapters (BSWS-A). 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 14: Kit For Customer-Specific Top Jaws (Bsws-Ur)
For mounting on the gripper, two adapters (BSWS-AR) are necessary, } 1.4 [/ 7]. NOTE The customer-specific top jaw with the kit (BSWS-URM) cannot be combined with the adapters (BSWS-A). 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 15: Assembly
Property damage due to incorrect top jaws! When using top jaws, the maximum permissible length and the maximum weight must not be exceeded. Observe the catalog data sheet. 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 16: Assembly Of Quick-Change Jaw System
For the "SD" (dustproof) gripper variant, the screws are too short. Use longer screws for variant "SD". These are not included in the scope of delivery. Tightening torque Size Tightening torque [Nm] Tab.: Mounting screws, base 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 17: Assembling The Adapter On The Top Jaw
Assembling the adapter on the top jaw Fasten both adapters (1) to the top jaw (2) with screws (3). ð Secure the screws with Loctite No. 243. ð Observe the tightening torque. 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 18: Assembling The Top Jaw On The Base
For this purpose, only one base is equipped with the alignment pin and the corresponding top jaw with the corresponding bore hole. 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 19: Assembly Of Quick-Change Jaw System Without Additional Height
For the "SD" (dustproof) gripper variant, the screws are too short. Use longer screws for variant "SD". These are not included in the scope of delivery. Tightening torque Size Tightening torque [Nm] Tab.: Mounting screws, adapter 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 20: Assembling The Top Jaw On The Gripper
Optional: Unscrew the unlocking button (3) if the projection causes space problems or if unintentional actuation is to be prevented. 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 21: Assembly Of The Kit For Customer-Specific Top Jaws
Sectional drawing of a customer-specific top jaw Gripper 5 Bore hole set-screw with pin 2 Top jaw 6 Top jaw, gripper center face 3 Adapter Tool center point 4 Bore hole, lock bolt 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 22: Assembling The Locking Mechanism In The Top Jaw
Carefully screw in the set-screw (2) to the stop and turn back by a quarter turn. ð Gewindestift (2) bleibt dabei in der Bohrung versenkt. ð Darauf achten, dass kein Loctite in die Bohrung des Verriegelungsbolzen gelangt. 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 23: Assembling The Adapter On The Gripper
5.3.4 Assembling the top jaw on the gripper The top jaws are assembled on the gripper in the same way as for the quick-change jaw system without additional height, [/ 20]. } 5.2.2 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 24: Maintenance
Tab.: Recommended lubricants Details on the SCHUNK lubricant designations are available at schunk.com/lubricants The product contains food-compliant lubricants as standard. The requirements of standard EN 1672-2:2020 are not fully met. 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 25: Maintenance Of Quick-Change Jaw System
Size 50-125:Apply Loctite No. 222 to the set-screw (8). Baugröße 160-300: Apply Loctite No. 243 to the set-screw (8). Assemble the product and mount it on the gripper, [/ 16]. } 5.1 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... -
Page 26: Maintenance Of Quick-Change Jaw System Without Additional Height
6.5 Maintenance of the kit for customer-specific top jaws The top jaws are disassembled, serviced and assembled in the same way as for the jaw quick-change system without additional height, [/ 26]. } 6.4 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961... - Page 27 05.00 | BSWS-M | Assembly and Operating Manual | en | 1580961...
- Page 28 SCHUNK SE & Co. KG Toolholding and Workholding | Gripping Technology | Automation Technology Bahnhofstr. 106 - 134 D-74348 Lauffen/Neckar Tel. +49-7133-103-0 info@de.schunk.com schunk.com Folgen Sie uns I Follow us Wir drucken nachhaltig I We print sustainable...
Need help?
Do you have a question about the BSWS-M and is the answer not in the manual?
Questions and answers