Subscribe to Our Youtube Channel
Related Manuals for Hasselblad Batch Feeder
Summary of Contents for Hasselblad Batch Feeder
- Page 1 User’s Guide Batch Feeder for Flextight 848, 949 and X5 Scanners English DK70030052...
-
Page 2: Table Of Contents
Impor tant Warnings and Restric tions System Requirements Batch Feeder Diagram Preparing the Feeder for First Use or af ter Shipping Mounting and Unmounting the Batch Feeder Mounting the Batch Feeder Unmounting the Batch Feeder Loading Originals into the Feeder... -
Page 3: Introduction
Introduction e Batch Feeder enables you to load up to 10 original holders (up to 60 originals, depend- ing on format) for batch scanning with your Flextight 848, 949 and X5 Scanner. is manual provides important information about using the Batch Feeder for your Flextight 848, 949 or X5 scanner. -
Page 4: Batch Feeder Diagram
Batch Feeder Diagram Figure 1: Hasselblad Flextight 848 Scanner with Batch Feeder Hasselblad Flextight 848, 949 or X5 Scanner. Batch Feeder Dust cover: to protect the originals and scanner entrance from dust. Magazine: showing original holder position 1. Magazine: showing original holder position 10. -
Page 5: Preparing The Feeder For First Use Or After Shipping
Feeder (for example, to a new studio See also “Preparing the Feeder for Storage or Shipping” on page 18 for more information about how to ship the Batch Feeder. Mounting and Unmounting the Batch Feeder correctly positioned for storage in its original box. - Page 6 Feeder and shuts itself down. e Mount feeder window updates with new instructions. connector (A) and a pair of mounting pins (B) as shown in Figure 3. Figure 3: Back panel of the Batch Feeder, showing the electronic connector (A) and mounting pins (B).
- Page 7 nector (A) and two mounting holes (B) inside the scanner, as shown below in Figure ese match the pins and connector of the Feeder. Figure 4: Flextight 949 Scanner with the batch-feeder panel open, showing the electrical connector (A) and mounting holes (B). Feeder with the holes and connector inside the scanner.
-
Page 8: Unmounting The Batch Feeder
Unmounting the Batch Feeder Maintenance > Feeder from the menu bar. e Feeder window opens. Press the Unmount button. the Mount feeder window.. Continue to prepare the scanner and Feeder for unmounting. e scanner shuts down and the Mount feeder window updates with new instruc- tions. -
Page 9: Loading Originals Into The Feeder
(To remove the original holder, just slide it NOTE! and down, starting from position 1. either loaded all of your originals or used all 10 slots of the Batch Feeder. -
Page 10: Scanning With The Batch Feeder
Scanning with the Batch Feeder Batch Scanning with 3f e Batch Feeder is intended as a tool for scanning large numbers of originals in a pro- poster and web page. the Feeder” on page 9. - Page 11 Destination Add job folder new sub-folder below the Destination Thumbnails Image Name Film Type Positive Setup or Negative Setup that you have selected. Film Type able (Positive Setup or Negative Setup selected. Save final TIFFs versions will also be saved in a sub-folder below the 3f images. Auto levels of each image.
-
Page 12: Custom Setups And Single Scans
Custom Setups and Single Scans example of how to use this feature when you have the Batch Feeder attached is given below, Batch Scan button to open the Batch Scan window. Feeder heading in the Batch Scan window by 3. Set the Position Preview FlexColor User’s... -
Page 13: Troubleshooting
Feeder will light. See also “Mounting the Batch Feeder” on page 5. Problem: The original holders are not fully drawn in or out of the scanner. - Page 14 Figure 6: Adjusting the Feeder angle to unmount the Batch Feeder from the scanner as described in “Unmounting the Batch Feeder” on page 8. bar with notches cut at each end. 6. Use the adjustment tool to loosen the nuts on the opposite side of the two adjustment bolts shown in Figure 7.
-
Page 15: Adjusting The Load Position
Feeder as described in “Unmounting the Batch Feeder” on page 8. bar with notches cut at each end. the Feeder as indicated in Figure 8. - Page 16 Continue. e scanner moves into its adjustment (home) position and the Align Feeder window updates with new instructions. on the Feeder as shown in Figure 9. Position the notch at the end of the tool over the adjustment pin inside the Feeder. Figure 9: Using the adjustment tool centered with reference to the grabber for the original holder inside the scanner (see also Figure 10).
- Page 17 Figure 10: Adjusting the Feeder position Continue in the Align Feeder window. e scanner now shuts down and the Align Feeder window updates with new instruc- tions. the rear of the Feeder (see also Figure 8, above). Continue in the Align Feeder window. Align Feeder window updates to tell you that the procedure is complete.
-
Page 18: Preparing The Feeder For Storage Or Shipping
14. Load original holders into all 10 original holder slots and then scan all of them using Preparing the Feeder for Storage or Transport Storing the Feeder To store the Feeder while it is not in use: Feeder” on page 8. sturdy cardboard and includes a foam lining custom cut to hold the Feeder safely and securely. -
Page 19: Preventive Maintenance
its original box. Preventive Maintenance that the feeder is mounted for all scans. Please note that previews are also counted as scans. monitoring the number of scans. by the factory warranty. Disposal Technical Information Specifications Scanner supported Flextight 848, 949 and X5 Scanner footprint with feeder Weight Maximum batch... -
Page 20: Ce Declaration
CE Declaration © 2010 Hasselblad A/S. All rights reserved. e information in this manual is furnished for informational use only, is subject to may appear in this manual.
Need help?
Do you have a question about the Batch Feeder and is the answer not in the manual?
Questions and answers