Table of Contents
Advertisement
Quick Links
ПРЕДПРИЯТИЕ МАКСАЭРО
• Производство воздуховодов и систем вентиляции
• Клапаны противопожарные
• Клапаны дымоудаления
• Вентиляторы общепром, дымоудаления, крышные
220056, г. Минск, ул. Стариновская, 15
Тел./факс: +375 17 244-67-44, 258-67-51, 347-73-56, 252-54-27
Velcom: +375 29 603-88-99
E-mail: olegaero@yandex.by
www.maxaero.by
Когтевые компрессоры
MM 1104-1142 BP
Advertisement
Table of Contents
Related Manuals for BUSCH MM 1104 BP
Summary of Contents for BUSCH MM 1104 BP
- Page 1 ПРЕДПРИЯТИЕ МАКСАЭРО • Производство воздуховодов и систем вентиляции • Клапаны противопожарные • Клапаны дымоудаления • Вентиляторы общепром, дымоудаления, крышные 220056, г. Минск, ул. Стариновская, 15 Тел./факс: +375 17 244-67-44, 258-67-51, 347-73-56, 252-54-27 Velcom: +375 29 603-88-99 E-mail: olegaero@yandex.by www.maxaero.by Когтевые компрессоры MM 1104-1142 BP...
-
Page 2: Table Of Contents
Technical Data......19 Busch – All over the World in Industry ....20... -
Page 3: Product Description
Condensable Vapours). Conveyance of other vapours shall be In order to avoid the suction of dust, the compressor is equipped with agreed upon with Busch. Conveyance of water or other liquids in an air filter (a) on the gas inlet. -
Page 4: Cooling
◆ Remove the tightening straps Prior to handling the compressor these installation and operating in- structions shall be read and understood. If anything remains to be clarified please contact your Busch representative! CAUTION Safety Notes Do not walk, stand or work under suspended loads. -
Page 5: Conservation
However, tures of more than 70 °C. VCI-products may attack the surfaces of plastics and elastomers. Seek advice from your local packaging dealer! Busch uses CORTEC Risk of burns! VCI 126 R film for the overseas packaging of large equipment. -
Page 6: Electrical Connection / Controls
● Mount the NEMA-adaptor flange (I) on the motor (the bolts (II) are not part of the Busch scope of delivery) ● Undo the cylinder screws (VI) and remove the elastomer part (V) from the hub (III) ●... -
Page 7: Connecting Lines/Pipes
(Ú page 8: Conveying CAUTION Condensable Vapours). Conveyance of other vapours shall be agreed upon with Busch. Conveyance of water or other liquids in Operation in the wrong direction of rotation can destroy the liquid phase increases the power consumption and shall therefore compressor in short time. -
Page 8: Conveying Condensable Vapours
The level of the synchronising gear should stay constant over the life- under pressure. time of the oil. If the level does fall, the gear is leaky and the compressor requires repair (Busch service). Risk of injury when the condensate drain cock is opened! Every 6 Months: Drain condensate only when the compressor is shut down and the ●... -
Page 9: Every 20000 Operating Hours, At The Latest After 6 Years
Note : The change interval of 20000 operating hours is valid for the gear oil Busch VS 150 only. Other gear oils reduce the change interval. This adjustment will be lost during dismantling of the compressor. ● Change the synchronising gear oil... -
Page 10: Troubleshooting
(s) as required and reassemble Internal parts are worn or damaged Repair the compressor (Busch service) The compressor does not start The drive motor is not supplied with the cor- Supply the drive motor with the correct volt-... - Page 11 (the proper function of the fan wheel requires the precise adjustment of the coupling on the motor shaft and on the pump shaft; therefore the motor can be mounted by the Busch ser- vice only) The compressor is blocked Solid foreign matter has entered the...
- Page 12 Ambient temperature too high Observe the permitted ambient temperatures Temperature of the inlet gas too high Observe the permitted temperatures for the inlet gas Insufficient gas transfer Provide a pressure relief valve Mains frequency or voltage outside tolerance Provide a more stable power supply range Adjust, repair or replace, respectively In case a pressure relief valve/regulating system...
-
Page 13: Sectional Drawing
Sectional Drawing VTx4 , DT , DT Sectional Drawing MM 1104, 1144, 1102, 1142 BP page 13 0870139163 / 100831... -
Page 14: Spare Parts
0-9-414 7782 Fax: 0-9-414 7783 Find the list of Busch companies all over the world (by the time of the publication of these installation and operating instructions) on page20(rear cover page). Find the up-to-date list of Busch companies and agencies all over the world on the internet atwww.busch-vacuum.com. -
Page 15: Ec-Declaration Of Conformity
EC-Declaration of Conformity Note: This Declaration of Conformity and the CE-mark affixed to the nameplate are valid for the machine within the Busch scope of delivery. This Declaration of Conformity is issued under the sole responsibility of the manufacturer. When this machine is integrated into a superordinate machinery the manufacturer of the superordinate machinery (this can be the operating company, too) must conduct the conformity assessment process for the superordinate machine or plant, issue the Declaration of Conformity for it and affix the CE-mark. -
Page 16: Technical Data
Technical Data For motor connection parameters see nameplate Type ~185 ~190 ~185 1500 ~195 MM 1104 BP ~190 ... ~185 1800 ~190 ~195 ~185 ~190 ~185 1500 ~195 MM 1144 BP ~190 ~210 ~190 1800 ~195 ~210 ~190 ~210 ~215...
Need help?
Do you have a question about the MM 1104 BP and is the answer not in the manual?
Questions and answers