BUSCH Mink MM 1144 BP Installation And Operating Instructions Manual
Hide thumbs
Also See for Mink MM 1144 BP:
- Instruction manual (24 pages) ,
- Instruction manual (32 pages)
Table of Contents
Related Manuals for BUSCH Mink MM 1144 BP
Summary of Contents for BUSCH Mink MM 1144 BP
- Page 1 Installation and Operating Instructions Compressors Mink MM 1104, 1144, 1102, 1142 BP gas tight Busch Produktions GmbH Schauinslandstr. 1 79689 Maulburg Germany 0870141300 / 190527 / Original instructions / Modifications reserved...
-
Page 2: Table Of Contents
Technical Data......16 Busch – All over the World in Industry ....20... -
Page 3: Product Description
(Ú page 8: Conveying Condensable Vapours). Conveyance of other vapours shall be agreed upon with Busch. Conveyance of water or other liquids in The compressor is intended for liquid phase increases the power consumption and shall therefore –... -
Page 4: Principle Of Operation
In case the compressor is fastened to the pallet by means of tightening structions shall be read and understood. If anything remains to be straps: clarified please contact your Busch representative! ◆ Remove the tightening straps CAUTION Do not walk, stand or work under suspended loads. -
Page 5: Storage
VCI-products may attack the surfaces of plastics and elastomers. Seek a clearance of minimum 1 m between the compressor and nearby advice from your local packaging dealer! Busch uses CORTEC walls VCI 126 R film for the overseas packaging of large equipment. -
Page 6: Gas Inlet
● Mount the NEMA-adaptor flange (I) on the motor (the bolts (II) are not part of the Busch scope of delivery) Pressure Connection ● Undo the cylinder screws (VI) and remove the elastomer part (V) ●... -
Page 7: Connecting Electrically
Connecting Electrically Star connection, multi-voltage motor (high voltage): WARNING Risk of electrical shock, risk of damage to equipment. Electrical installation work must only be executed by qualified per- sonnel that knows and observes the following regulations: - IEC 364 or CENELEC HD 384 or DIN VDE 0100, respectively, - IEC-Report 664 or DIN VDE 0110, - BGV A2 (VBG 4) or corresponding national accident prevention regulation. -
Page 8: Conveying Condensable Vapours
Condensable Vapours). Conveyance of other vapours shall be by warming up the compressor, conveyance of ambient air after agreed upon with Busch. Conveyance of water or other liquids in process end and regular draining of the anti-pulsation chamber (l). liquid phase increases the power consumption and shall therefore be avoided (risk of drive overload). -
Page 9: Maintenance Schedule
● Remove the eyebolt (f, 615) In case of higher requirements in terms of gas tightness: ● Remove the lid (424) ◆ Replace the shaft seal rings (Busch service) Maintenance MM 1104, 1144, 1102, 1142 BP gas tight page 9... -
Page 10: Every 20000 Operating Hours, At The Latest After 6 Years
Busch service will only accept compressors that come with a completely filled in and legally binding signed “Declaration of Contamination” CAUTION (form downloadable from www.buschvacuum.com). Pressurised air supply systems supply a too high pressure. Removal from Service Risk of damage to the compressor. -
Page 11: Troubleshooting
(t, 714) as required and reas- semble Internal parts are worn or damaged Repair the compressor (Busch service) The compressor does not start The drive motor is not supplied with the cor- Supply the drive motor with the correct volt-... - Page 12 (the proper function of the fan wheel requires the precise adjustment of the coupling on the motor shaft and on the pump shaft; therefore the motor can be mounted by the Busch ser- vice only) The compressor is blocked Solid foreign matter has entered the...
- Page 13 Ambient temperature too high Observe the permitted ambient temperatures Temperature of the inlet gas too high Observe the permitted temperatures for the inlet gas Insufficient gas transfer Provide a pressure relief valve Mains frequency or voltage outside tolerance Provide a more stable power supply range Adjust, repair or replace, respectively In case a pressure relief valve/regulating system...
-
Page 14: Spare Parts
0-9-414 7782 Fax: 0-9-414 7783 Find the list of Busch companies all over the world (by the time of the publication of these installation and operating instructions) on Ú page 20 (rear cover page). Find the up-to-date list of Busch companies and agencies all over the world on the internet at www.buschvacuum.com. -
Page 15: Eu Declaration Of Conformity
EU Declaration of Conformity Note: This Declaration of Conformity and the CE-mark affixed to the nameplate are valid for the machine within the Busch scope of delivery. This Declaration of Conformity is issued under the sole responsibility of the manufacturer. -
Page 16: Technical Data
Technical Data For motor connection parameters see nameplate Type ~185 ~190 ~185 1500 ~195 MM 1104 BP ~190 ... ~185 1800 ~190 ~195 ~185 ~190 ~185 1500 ~195 MM 1144 BP ~190 ~210 ~190 1800 ~195 ~210 ~190 ~210 ~215 3000 ~240 MM 1102 BP... - Page 17 MM 1104, 1144, 1102, 1142 BP gas tight page 17 0870141300 / 190527...
- Page 18 MM 1104, 1144, 1102, 1142 BP gas tight page 18 0870141300 / 190527...
- Page 19 MM 1104, 1144, 1102, 1142 BP gas tight page 19 0870141300 / 190527...
-
Page 20: Busch - All Over The World In Industry
Busch – All over the World in Industry www.buschvacuum.com Norway Australia Dr.-Ing. K. Busch GmbH Außenstelle Neuenrade Busch Australia Pty. Ltd. Busch Vakuumteknikk AS Breslauer Str. 36 Hestehagen 2 30 Lakeside Drive 58809 Neuenrade 1440 Drøbak Broadmeadows, Vic. 3047 Tel: (0 23 92) 50 29 92...
Need help?
Do you have a question about the Mink MM 1144 BP and is the answer not in the manual?
Questions and answers