1. Manuals
  2. Brands
  3. Total Manuals
  4. Trimmer
  5. TMT55211
  6. Product manual

Total TMT55211 Product Manual

4-in-1 gasoline hedge trimmer multi tool
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
105g 有光铜版纸
骑马钉
风琴折 + 对折 页面顺序
16P 页面顺序
9
10
11
12
13
14
1
2
3
5
6
7
1.更新新版本，
更新公司名地址
更
改
记
录
T0424.V03
2024.4.25
版本号
日期
封面
封底
4
8
QQY
设计师
105*143mm
20P 页面顺序
11
封面
12
13
14
15
16
17
18
封底
1
2
3
4
5
6
7
8
9
10

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the TMT55211 and is the answer not in the manual?

Questions and answers

Related Manuals for Total TMT55211

Summary of Contents for Total TMT55211

  • Page 1 105g 有光铜版纸 105*143mm 骑马钉 风琴折 + 对折 页面顺序 16P 页面顺序 20P 页面顺序 封面 封面 封底 封底 1.更新新版本， 更新公司名地址 更 改 记 录 T0424.V03 2024.4.25 版本号 日期 设计师...

  • Page 2: Product Manual

    PRODUCT MANUAL 4-IN-1 GASOLINE HEDGE TRIMMER MULTI TOOL TMT55211...

  • Page 3: General Safety Warnings

    | English Original Instructions GENERAL SAFETY WARNINGS Proper safety precautions must be observed. Like all power equipment this unit must be handled carefully. DO NOT EXPOSE YOURSELF OR OTHERS TO DANGER. Follow these general rules. Do not permit others to use this machine unless they are thoroughly responsible and have read, and understand the machine manual and are trained in its operation.
  • Page 4 | English during cutting.  Keep children away. Onlookers should be kept at a safe distance from the work area, at least 15 meter (50 feet) Never leave the machine unattended.   Do not use this unit for any job other than those for which it is intended as described in this manual.
  • Page 5 | English The engine should be turned off when the machine is moved between work  areas.  Be careful not to hit the nylon cutting head against stones, or the ground. Unreasonable rough operation will shorten the life of the machine as well as ...
  • Page 6 Always wear ear protection, loud noise for long time can make hearing debase even lost hearing.  Total face and head protection must be worn to prevent damage from plummet or branch. Wear no-slip heavy duty work gloves to improve your grip on the brush cutter ...
  • Page 7 | English Kickback and related warnings  Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory’s rotation at the point of the binding.
  • Page 8 | English THE SYMBOLS IN INSTRUCTION MANUAL Read the instruction manual before using. Safety alert. Please only use the accessories supported by the manufacturer. Wear safety glasses, hearing protection and dust mask. Waste electrical products should not be disposed of with household waste.
  • Page 9 | English THE SYMBOLS IN INSTRUCTION MANUAL Exhausting gas is dangerous. Do not inhale them. Do not smoke. Caution: the accessible surface maybe hot when using the too. Guarantee noise level Maximal rotation of speed of the spindle.

  • Page 10: Additional Safety Warning

    | English ADDITIONAL SAFETY WARNING Even if you use this tool correctly, there are always residual risks. The following hazards may arise in connection with the structure and manufacture of this power tool: Hearing impairment if no suitable hearing protection is worn. Cuts if no suitable protective clothing is worn.
  • Page 11 | English The pole pruner is exclusively intended for pruning trees and/or cutting small wood from the ground. Any other use is considered improper and will damage the tool. The correct use also includes reading and observing the instructions for use at each use as well as observing the warnings fixed on the machine.

  • Page 12: Specifications

    | English SPECIFICATIONS Components ON/OFF Switch 11. Shoulder strap Throttle lever 12. Cutting head for grass trimmer Hanger 13. Handle Mounting tube 14. Hedge trimmer Carter of protection (brush cutter and 15. Air filter trimmer) 16. Choke lever Bottle for the oil mixture 17.

  • Page 13: Hedge Trimmer

    | English Pole mounted pruner 1. Tube 2. Oil tank for lubrication 3. Saw chain Hedge trimmer 1. Tube 2. Adjustment lever 3. Notching of adjustment 135° from cutting unit 4. Blade Brush cutter...

  • Page 14: Technical Specifications

    | English 1. Carter of protection 2. 3-teeth blade 1. Nylon wire 2. Device of cutting the nylon wire 3. Carter of protection Technical specifications Engine information. Type of engine RY1E44F-5, 2-stroke engine Volume of the fuel tank 1200 cm³ Max engine speed Max.
  • Page 15 | English Hedge trimmer Unit without cutting attachment, empty tank 7.9 kg Cutting length 390 mm Type of the hedge trimmer blade PN410/ HUZHOU JINLIFU YK-58/YINKE Engine speed with hedge trimmer 10000 minˉ¹ attachment Gear ratio 28:7 Vibrations 7.2m/s². K= 1.5 m/s² Noise emission Sound pressure: LpA, av = 93dB (A) Sound power: LwA, av = 113dB (A)
  • Page 16 | English OPERATION PICTURE...
  • Page 17 | English OPERATION PICTURE...

  • Page 18: Operation

    | English OPERATION Install the front handle as shown in the picture below. Be sure to orient the stem toward the hole. Do not fasten the screws until you have set the most comfortable working position with the straps. The front handle must be oriented as shown in the picture for "the motor and drive unit".(See Figure A) Install the desired tube on the bar of the main unit.
  • Page 19 | English To remove the nylon cutting head, put a metal locking tool into the tool and then unscrew the nylon cutting head. Hedge trimmer (See Figure F) Install the bar of the main unit. Be sure that the locking pin is inserted in the hole of the bar Fix the bar by turning the nut anticlockwise.

  • Page 20: Filling Tank

    | English of the chain (4) so that the chain can be lifted a few millimeters from the center of the guide rail.  Secure the safety screw. Installation of the harness Hang the harness in its dedicated location on the tube. Adjust the size of the harness properly to have a correct working position.
  • Page 21 | English Switch off the engine before adding fuel. Shake the mixture thoroughly before  filling the tank.  Store gasoline in tanks specially designed for this purpose. Fill the fuel tank of your appliance outdoors and avoid smoking during work. ...
  • Page 22 | English IMPORTANT MIX THE MIXTURE CAREFULLY. Measure the fuel and oil needed for the fuel mixture. Pour a little gasoline into a clean container provided for this purpose. Add all the oil before stirring the can. Add remaining gasoline and shake the can for at least 1 minute. Certain oils mix with difficulty because of the substances they contain.
  • Page 23 | English Observe local regulations when disposing of used containers. UTILISATION a）Starting the 4-in-1 multifunction tool Do not start the appropriate module of the machine until all components have been connected correctly! Attach the cutting blade of the brush cutter with a torque of 20 Nm and the cutting head of the mower with a tightening torque of 15Nm.
  • Page 24 | English ⚠ WARNING: The machine is equipped with a centrifugal clutch system. When starting the engine, place the machine on a level, clean floor and hold it firmly to prevent the sharp components or the throttle lever from coming into contact with any objects when the engine is started.
  • Page 25 | English wire mesh or chain linked fence be careful to feed only up to wire. If you go too far the line will snap off around the wire. Trimming can be done to cut through weed stems one at a time. Place the trimmer line head near the bottom of the weed-never high up which could cause the weed to chatter and catch the line.
  • Page 26 | English d. Using the brush cutter Be sure that you have installed the correct accessory.  Do not use the brush cutter for cutting trees.  Do not cut with dull, cracked or damaged meal blade. Before cutting growth, inspect for obstructions such as boulders, metal stakes ...
  • Page 27 | English Warning! Never place the cutting head on the ground while the machine is running.  It is recommended to cut the trapezoidal hedges to prevent the lower branches from being stripped. This corresponds to the natural growth of plants and hedges can be potentially prosperous.
  • Page 28 | English 60°max. Care and maintenance Regularly maintain your tool. This will keep your tool running smoothly and extend its life. The tool must always be kept in good working order. Do not use abrasive, caustic products to clean the tool. These types of products will damage your tool.
  • Page 29 | English Always switch the drive unit off when performing any maintenance or repair work. Repairs should only be carried out by authorized specialists with the necessary technical knowledge. Interventions by non-specialists may damage the machine or be hazardous to safety. Follow the instructions below: ...

  • Page 30: Air Filter

    | English MAINTENANCE&MALFUNCTIONS Air filter Accumulated dust in the air filter will reduce engine efficiency. Increase fuel  consumption and allow abrasive particles to pass into the engine. Remove the air filter as often as necessary to maintain in a clean condition. Light surface dust can readily be removed by tapping the filter.
  • Page 31 | English Confirm that the fuel is not leaked from tank.   Transport the tool in a way to prevent loss of fuel, injuries and damage.  Dismantle the cutting head and the blade before transport and storage. Put the blade in its packing.
  • Page 32 | English Covered with Clean or replace. carbon Fouled Clean or replace plug with fuel. Plug defective Engine runs, but dies or does not Air filter Air filter dirty Normal wear Clean or replace accelerate properly Fuel filter Contaminants/r Fuel filter Replace dirty esidues in fuel...
  • Page 33 TOTAL TOOLS WORLD MADE IN CHINA T0424.V03 NEWWAY TECHNOLOGY (SUZHOU) CO., LIMITED No.20 Dagang Road, Fuqiao Town, Taicang City, China...

Table of Contents