Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Troubleshooting
Related Manuals for Total TP425381
Summary of Contents for Total TP425381
- Page 1 GASOLINE GRASS TRIMMER TP425381 25cc 15" 25cc 15"...
-
Page 2: Safety Rules & Precautions
SAFETY RULES & PRECAUTIONS Proper safety precautions must be observed. Like all power equipment this unit must be handled carefully. DO NOT EXPOSE YOURSELF OR OTHERS TO DANGER. Follow these general rules. Do not permit others to use this machine unless they are thoroughly responsible and have read, and understand the machine manual and are trained in its operation. - Page 3 Do not overreach. Keep proper footing and balance at all times. Do not run the unit while standing on a ladder or on any other unstable footing location. Keep hands and feet clear of the nylon cutting head while unit is in use.
- Page 4 Always wear ear protection, loud noise for long time can make hearing debase even lost hearing. Total face and head protection must be wearing to prevent damage from plummet or branch. Wear no-slip heavy duty work gloves to improve your grip on the brush cutter handle.
- Page 5 WARNINGS Because a trimmer/cutter is a high-speed, fast cutting power tool, special safety precaution must be observed to reduce the risk of personal injury. Read this manual carefully. Be familiar with the controls and the proper use of the unit. Know how to shut it off, and how to unhook a harnessed unit quickly.
-
Page 6: Specification
Specification MODEL TP425381 Direct Drive Remote type Flexible shaft Max. speed(rpm) 8140 Idle speed(rpm) 3000±150 Vibration values Main each handle(m/s Sound pressure unit values[dB(A)] Guaranteed Sound power values [dB(A)] Line cutting width 15 /380 mm Nylon head rotation Clockwise(seen from the top) -
Page 7: Before Operation
Before operation SAFETY MANUAL included with unit. Read before operating and keep for future reference to learn proper, safe operating techniques. NYLON CUTTER HEAD Contains replaceable nylon trimming line that advances when the trimmer head is tapped against the ground while the head is turning at normal operating speed. -
Page 8: Handle Assembly
CHOKE the choke control is located on the top of the filter cover. STARTER HSNDLE pull handle until engine starts, then return handle slowly. DO NOT let handle snap back or damage to starter will occur. ASSEMBLY INSTRUCTIONS HANDLE ASSEMBLY NOTE: The Delta Handle is attached to the shaft but has been turned under for ease of packing. -
Page 9: Cutting With A Nylon Head
DANGER ZONE NO PERSON EXCEPT OPERATOR ALLOWED 15 METERS RADIUS DANGER ZONE. EYE, EAR, FACE, FOOT, LEG AND BODY PROTECTION MUST BE WORN BY OPERATOR. PERSONS IN ZONE OR RISK BEYOND DANGER ZONE SHOULD WEAR EYE PROTECTION AGAINST THROWN OBJECTS. RISK DIMINISHES WITH DISTANCE FROM DANGER ZONE. - Page 10 WARNING DANGER Use only quality nylon monofilament line of the diameter 2 mm. Never use wire or wore-reinforced line in place of nylon trimmer line. Load your nylon line cutting head only with ny n trimmer WARNING DANGER Use extreme caution when operating over bare spots and gravel, because WARNING DANGER line...
- Page 11 Trimming can be done to cut through weed stems one at a time. Place the trimmer line head near the bottom of the weed-never high up which could cause the weed to chatter and catch the line. Rather than cut the weed right through, just use the very end of the line to wear through the stem slowly.
-
Page 12: Fuel & Oil Mixture
FUEL & OIL MIXTURE Never fill the fuel tank to the very top. Never add fuel to the tank in a closed non-ventilated area. Do not add fuel to this unit close to an open fire or sparks. Be sure to wipe off spilled fuel before attempting to start engine. -
Page 13: Check Points Before Operation
two months. Fuel mixture stored longer than this will cause hard starting and poor performance. If fuel mix has been stored longer than this time. It should be removed and filled with fresh mixture. 2. Never fill the fuel tank to the very top. 3. -
Page 14: Maintenance And Care
4. Push choke lever inwards (excessive cranking with choke lever will cause flooding engine making it difficult to start). 5. Pull starter handle until engine starts. 6. Allow engine to warm up for a few minutes before using. STARTING WARM ENGINE 1. -
Page 15: Troubleshooting
port with a piece of hooked wire. Check the fuel filter periodically. Do not allow dust to enter into fuel tank. Clogged filter will cause difficulty in starting engine or abnormalities in starting engine or abnormalities in engine performance. When filter is dirty, replace the filter. When the inside of the fuel tank is dirty, it can be cleaned by rinsing the tank out with gasoline. -
Page 16: Troubleshooting Guide
correctly; Compression of the engine is adequate. Dispose of fuel in tank. Insure that fuel is fresh and clean. Check fuel filter to make sure it is clean. (Replace filter if necessary). Make sure air filter elements are clean. Install new, properly gapped spark plug. When there is serious trouble with the unit, do not try to repair it yourself but have your distributor or dealer do it for you. -
Page 17: Low Output
piston ring attrite piston ring broken piston ring replace a new compress cementation replace press spark plug eliminate looseness tighten fuel shortage conjoint surface eliminate Ignition of the syste cylinder System crank cast leak norm normal High voltage wire and spark tighten the spark plug Compress Plug... - Page 18 3. ENGINE RUNNING UNSTABLE symptom Probable cause Remedy piston piston ring replace piston piston there are metal knock cylinder attrite sound ring piston piston replace piston pin attrite bearing of crank shaft piston attrite replace bearing there are metal knock engine overheats avoid use it for long time...
- Page 19 TP425381 Spare Part List Part Description Part Description Rope wheel covering 1.27 Hookup set of the shaft Nylon rope(2X5mm) 1.28 Flexible shaft B 1.16 Nut M5 GB889-86 1.41 Switch handle B 1.19 Bolt M6X50 GB5780-86 1.44 Shock attenuation tube Nut M6 GB62-88A 1.45...
- Page 20 TP425381 Exploding view...
- Page 21 TP425381 Engine Spare Part List Part Description Part Description screw ST4.8*25 fuel vitta 2.B1 2.32 screw M5*20 vitta seat 2.B2 2.33 clutch cover cleanner 2.34 nut M5 protective film 2.35 connect fuel tank 2.36 oil-box-cover flying rings washer 8 2.37...
- Page 22 TP425381 Exploding view...
- Page 23 GASOLINE GRASS TRIMMER www.totaltools.cn TOTAL TOOLS CO.,LIMITED MADE IN CHINA T1212.V01 25cc 15" 25cc 15"...
Need help?
Do you have a question about the TP425381 and is the answer not in the manual?
Questions and answers