Advertisement
TOSHIBA Barcode Printer
B-FV4D-GL SERIES
Quick Installation Manual
Important Information to the User
In order to meet Product Safety, FCC and CE marking requirements, use the
approved power cord that meets the following standards.
Power Cord
For this product a UL listed, detachable power cord is required. Outside the US,
power cords need to meet the certification for the particular country/region and
application requirements. If a different power cord is used from that described
above you might violate safety certifications which are in force in the
country/region of use.
equipment and must be easily accessible.
Pull out the plug from the outlet more than once a year to clean around the
prongs. Accumulating dust and dirt could cause a fire due to the heat released
by electric leakage.
NOTES:
1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC
CORPORATION.
2. The contents of this manual may be changed without notification.
3. Please refer to your local Authorized Service representative with regard to any queries you may have in
this manual.
The socket-outlet needs to be installed near the
E-1
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Toshiba B-FV4D-GL Series
Summary of Contents for Toshiba B-FV4D-GL Series
- Page 1 Accumulating dust and dirt could cause a fire due to the heat released by electric leakage. NOTES: 1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC CORPORATION. 2. The contents of this manual may be changed without notification.
- Page 2 Cleaner Pen (1 pc.) Cutter Tray (1 pc.) NOTES: 1. Check for damages or scratches on the printer. However, please note that TOSHIBA TEC CORPORATION shall have no liability for any damage of any kind sustained during transportation of the product.
-
Page 3: Printer Overview
Printer Overview Media View Window LED 2 Appearance 2.1.1 Front View LED 1 FEED Button Media Outlet The diagrams below show all the possible cable connections to the 2.1.2 Rear View current versions of the printer. ... - Page 4 CAUTION! To avoid injury, be careful not to trap your fingers in the Paper Slot while opening or closing the Top Cover. Paper Slot 2.1.3 Interior WARNING! The print head becomes very hot during printing. Do not Print Head touch the print head or touch around it directly after printing.
-
Page 5: Turning On The Printer
Turning the Printer When the printer is connected to a host computer it is good practice to turn the printer ON before turning on the host computer and to turn ON/OFF OFF the host computer before turning off the printer. Turning ON the NOTE: Printer... -
Page 6: Turning Off The Printer
1. Before turning off the printer power switch, verify the following: Turning OFF the LED 1 is illuminated in green, not flashing. Printer LED 2 is extinguished. CAUTION! 2. To turn OFF the printer power, press the power switch as shown in 1. -
Page 7: Loading The Media
This section describes how to load the media in the printer. This Loading the Media printer is intended for printing label (without liner) rolls. Please use TOSHIBA TEC CORPORATION approved media. WARNING! 1. Do not touch any moving NOTES: parts. To reduce the risk of 1. - Page 8 2. Press the Media Roll Holder Lever down and outward, set the media between the Media Roll Holders ensuring that the printing side is facing up. Release the Media Roll Holder Lever to clamp the media roll securely. NOTES: 1. Media path Transmissive Sensor Platen Media Roll Holder Lever...
- Page 9 4. Pass the media through the media outlet of the cutter block. Media Outlet 5. Close the Top Cover gently, then press the [FEED] button to check the media feeds correctly. FEED Button...
- Page 10 PRINTED IN TAIWAN EO1-33113 © 2015 TOSHIBA TEC CORPORATION All Rights Reserved R151120R7900-TTEC 1-11-1, Osaki, Shinagawa-ku, Tokyo 141-8562, JAPAN Ver00F 2015-12 E-10...
Need help?
Do you have a question about the B-FV4D-GL Series and is the answer not in the manual?
Questions and answers