Download
Share
Print this page
Toshiba B-FV4D-GH Series Quick Installation Manual
  1. Manuals
  2. Brands
  3. Toshiba Manuals
  4. Barcode Reader
  5. B-FV4D-GH
  6. Quick installation manual
Toshiba B-FV4D-GH Series Quick Installation Manual

Toshiba B-FV4D-GH Series Quick Installation Manual

Hide thumbs Also See for B-FV4D-GH Series:

Advertisement

Quick Links

Download this manual
TOSHIBA Barcode Printer
B-FV4D-GH SERIES
Quick Installation Manual
Important Information to the User
In order to meet Product Safety, FCC and CE marking requirements, it is
advised to use the power cord which was shipped with this product. Otherwise
this cable needs to meet the following standards.
Power Cord
For this product a UL listed, detachable power cord is required. Outside the US,
power cords need to meet the particular country's certification and application
requirements. If a different power cord is used from that described above you
might violate safety certifications which are in force in the country of use. The
socket-outlet needs to be installed near the equipment and must be easily
accessible.
Pull out the plug from the outlet more than once a year to clean around the
prongs. Accumulating dust and dirt could cause a fire due to the heat released
by electric leakage.
NOTES:
1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC
CORPORATION.
2. The contents of this manual may be changed without notification.
3. Please refer to your local Authorized Service representative with regard to any queries you may have in
this manual.
E-1

Advertisement

loading

Related Manuals for Toshiba B-FV4D-GH Series

Summary of Contents for Toshiba B-FV4D-GH Series

  • Page 1 Accumulating dust and dirt could cause a fire due to the heat released by electric leakage. NOTES: 1. This manual may not be copied in whole or in part without prior written permission of TOSHIBA TEC CORPORATION. 2. The contents of this manual may be changed without notification.
  • Page 2 Safety Precautions (1 copy) USB Cable (1 pc.) NOTES: 1. Check for damages or scratches on the printer. However, please note that TOSHIBA TEC CORPORATION shall have no liability for any damage of any kind sustained during transportation of the product.

  • Page 3: Printer Overview

    Printer Overview Media View Window LED 2 Appearance LED 1 2.1.1 Front View FEED Button Media Outlet The diagrams below show all the possible cable connections to the 2.1.2 Rear View current versions of the printer.     ...
  • Page 4 CAUTION! To avoid injury, be careful not to trap your fingers in the Paper Slot while opening or closing the Top Cover. Paper Slot 2.1.3 Interior WARNING! The print head becomes very hot during printing. Do not touch the print head or touch Print Head around it directly after printing.

  • Page 5: Turning On The Printer

    Turning the Printer When the printer is connected to a host computer it is good practice to turn the printer ON before turning on the host computer and to turn ON/OFF OFF the host computer before turning off the printer. Turning ON the NOTE: Printer...

  • Page 6: Turning Off The Printer

    1. Before turning off the printer power switch, verify the following: Turning OFF the LED 1 is illuminated in green, not flashing. Printer LED 2 is extinguished. CAUTION! 2. To turn OFF the printer power, press the power switch as shown in 1.

  • Page 7: Loading The Media

    This section describes how to load the media in the printer. This Loading the Media printer accepts label rolls. Please use TOSHIBA TEC CORPORATION approved media. WARNING! 1. Do not touch any moving NOTES: parts. To reduce the risk of 1.
  • Page 8 1. Open the Top Cover while pulling the Lock Release Portions as indicated by the arrows. Top Cover Lock Release Portion NOTE: Media path For the outside-wound media Feed Gap Sensor 2. Press the Media Roll Holder Lever down and outward, set the media between the Media Roll Holders ensuring that the printing side is facing up.
  • Page 9 3. Pass the media through the Media Guides. Pull the media until it reaches the front of the printer. Media Guide Media Guide 4. Check and select the sensor type to be used. (Refer to the Owner’s Manual.) This printer has a Feed Gap Sensor which detects inter-label gaps. NOTES: As the Feed Gap Sensor position is fixed, it is not necessary to 1.
  • Page 10 5. Close the Top Cover gently, then press the [FEED] button to check the media feeds correctly. FEED Button There are two issue modes available for this printer. NOTES: Batch mode: 1. To separate the printed media from the printer in In the batch mode, the media is continuously printed and fed until the batch mode, be sure to number of prints specified in the issue command has been printed.
  • Page 11 Strip mode: When printing in strip mode, labels are automatically removed from the backing paper as each label is printed. NOTES:  How to set the media 1. When printing labels without When issuing labels in the strip mode, set the label in the following removing them from the backing procedure: paper, it is not necessary to pass...
  • Page 12 4. Close the Peel-off Unit and Top Cover. © 2015 TOSHIBA TEC CORPORATION All Rights Reserved 1-11-1, Osaki, Shinagawa-ku, Tokyo 141-8562, JAPAN PRINTED IN TAIWAN EO1-33104 R150520Q4900-TTEC Ver00 B 2015-05 E-12...