Page 1
Operating instructions Coffee machine To avoid the risk of accidents or damage to the appliance it is essential to read these instructions before it is installed and used for the first time. GB-en M.-Nr. 11 551 632...
Contents Caring for the environment ................Warning and Safety instructions..............Product description ..................15 Controls and indicators ..................16 Accessories ....................... 17 Operation......................18 Before using for the first time ................19 Water hardness....................21 Filling the water container ................22 Filling the coffee bean container ..............
Page 4
Contents Profiles........................ 35 Creating profiles ....................35 Changing drinks within a profile ................35 Making drinks stored in a profile ................. 35 Changing the name ..................... 35 Deleting a profile ....................36 Setting when the profile should change (Change profile) ........36 Settings ......................
Page 5
Contents Unusual performance of the coffee machine ............56 Unsatisfactory results..................62 After sales service and warranty ..............64 Contact in the event of a fault ................64 Warranty ......................65 Saving energy ....................66 Electrical connection ..................67 Installation......................68 Dimensions ......................
Miele cannot be held liable for injury or damage caused by non- compliance with these instructions. Keep these operating instructions in a safe place and pass them...
Page 7
Warning and Safety instructions Correct application This coffee machine is intended for home use. This coffee machine is not intended for outdoor use. This coffee machine must not be used at altitudes above 2000 m. It must only be used as a domestic appliance to make espresso, cappuccino, latte macchiato etc.
Page 8
Warning and Safety instructions Safety with children Danger of burning and scalding on the dispensing spouts. Children's skin is far more sensitive to high temperatures than that of adults. Ensure children do not touch hot surfaces of the coffee machine or place parts of their body under the dispensing spouts.
Page 9
The function and operation of the protective measures provided in the domestic electrical installation and in this Miele product must also be maintained in isolated operation or in operation that is not synchronised with the mains power supply, or these measures must be replaced by equivalent measures in the installation.
Page 10
Repairs may only be carried out by a Miele authorised service technician. While the machine is under warranty, repairs should only be undertaken by a Miele authorised service technician. Otherwise the warranty is invalidated.
Page 11
Warning and Safety instructions The coffee machine must be disconnected from the electricity supply during repair work. Never open the outer casing of the machine. Tampering with electrical connections or components and mechanical parts is highly dangerous to the user and can cause operational faults or electric shock.
Page 12
Warning and Safety instructions Correct use Danger of burning and scalding on the dispensing spouts. The liquids and steam dispensed are very hot. Keep well away from the area underneath the spouts when hot liquids and steam are being dispensed. Do not touch hot components.
Page 13
The machine must not be used for cleaning objects. Accessories and spare parts Miele can only guarantee the safety of the machine when original Miele spare parts are used. Faulty components must only be replaced by genuine Miele original spare parts.
Page 14
Descale the coffee machine regularly depending on the water hardness level in your area. Descale the machine more frequently in areas with very hard water. Miele cannot be held liable for damage arising from insufficient descaling, the use of incorrect descaling agent or the use of descaling agent which is not of the appropriate concentration.
Product description a Lower panel with drip tray cover g Grinder setting (behind the appliance door) b Central spout with Cappuccinatore h Brew unit (behind the appliance and hot water spout door) c On/Off button i Park position for milk tube d Control panel j Drip tray with lid and waste e Water container...
Sensor control For showing information about the Other drinks current action or status (CM 5410, CM 5510, Profiles d Optical interface CM 5710) (For Miele Customer Service Maintenance Department only) Parameters Settings e Arrow buttons For scrolling through lists, selecting j “2 portions” sensor entries or changing values For dispensing 2 portions of a drink...
These products and other useful Optional accessories accessories can be ordered via the Miele accessories and cleaning and Miele webshop, from Miele (see back conditioning products are available for cover for contact details) or from your your coffee machine. Miele dealer.
A bar Select drink on the right-hand side of the display indicates that further options or text are Miele available. To select an option, keep pressing the Select drink arrow buttons ...
Touch the On/Off button . cover into the lower panel. Place the coffee machine on a level The welcome message Miele – flat surface that is not sensitive to Wilkommen will appear on the display water (see “Installation”).
Page 20
Before using for the first time Please note that the full aroma of the coffee and typical crema will not develop fully until several coffees have been made. To ensure that any coffee residues from the factory testing process are removed from the brewing system, please throw away the first 2 cups of coffee when using the coffee...
Water hardness Water hardness is an indication of the Setting the water hardness amount of minerals dissolved in water. Touch the sensor control. The more minerals in the water, the higher the water hardness. The harder Select Settings | Water hardness the water is, the more frequently the...
Filling the water container Replace the water container and Risk to health due to close the lid. contaminated water. Bacteria can develop in water which Make sure that the water container has been sitting in the water handle is on the right so that the lid container for too long and is a risk to can close properly.
Filling the coffee bean container Coffee or espresso can be made from whole roasted coffee beans which are freshly ground in the coffee machine for each portion. This requires the coffee bean container to be filled with coffee beans. Alternatively, you can make coffee drinks with ready ground coffee.
Switching on and off Switching the coffee machine Switching the coffee machine Touch the On/Off button . Touch the On/Off button . The appliance heats up and rinses the If coffee has been dispensed, the coffee pipework. Hot water will run out of the machine will rinse the pipework central spout.
Adjusting the central spout to the correct cup height You can adjust the central spout to suit the height of the cup you are using so that the coffee or espresso will not cool down as quickly and the crema will have a better consistency.
Making drinks - Latte macchiato consists of 1 third Danger of burning and scalding each of hot milk, milk froth and on the dispensing spouts. espresso. The liquids and steam dispensed are - Caffè latte consists of espresso and very hot and can cause scalding. hot milk.
Making drinks Tip: Using cold cow’s milk (< 10 °C) with a protein content of at least 3 % will produce the perfect milk froth. You can select milk with a fat content according to preference. With whole milk (at least 3.5 % fat), the milk froth will be slightly creamier than with low- fat milk.
Other drinks Tip: The Miele milk container is the again. perfect addition to Miele coffee machines if you make a lot of coffees The coffee machine will stop with milk.
Miele for the “Coffee pot” function. You can make several cups of coffee The CJ JUG vacuum flask is available one after the other automatically with to order via the Miele webshop, from Coffee pot function (max. 0.75 litre), Miele (see back cover for contact e.g.
Making drinks Dispensing hot water (CM 5410, CM 5510, CM 5710) Please note that the water dispensed is not hot enough for making black tea. First take the lid off of the coffee bean container and then take the cover off the ground coffee chute. Place a maximum of 12 g in the ground coffee chute.
Degree of grinding The degree of grinding determines the The slide control for adjusting the contact time between the ground coffee degree of grinding is located on the top and the water, known as the extraction right behind the appliance door. time.
Quantity of coffee, brew temperature and pre-brewing You can set the quantity of coffee, the Tip: If the coffee is too strong for you or brewing temperature and pre-brewing it tastes bitter, try a different type of for each drink individually. To do this, bean.
Portion size The flavour of the coffee produced Cancelling portion size programming depends not only on the type of coffee, Touch the drinks sensor control again but also on the amount of water used. or the sensor control for drinks You can programme the amount of from Other drinks...
Page 34
Portion size Changing the portion sizes in the Parameters menu You can only change the portion sizes for Long coffee, Caffè Latte, hot milk and milk froth via the Parameters menu. Place a suitable container underneath the central spout. ...
Profiles Touch the sensor control. (CM 5410, CM 5510, CM 5710) In addition to the Miele drinks menu The Profiles menu opens. (Miele profile), you can create individual Select the profile you want. profiles to cater for different tastes and preferences. The name of the selected profile is shown in the top left of the display.
Select the profile you wish to delete. - After each use: The machine will Select and confirm with OK. revert to the Miele profile whenever a drink is dispensed. The profile will be deleted. - When switched on: The Miele profile...
Settings Displaying and changing Info (display information) Settings You can display the number of drinks dispensed so far and how many more The drinks menu is displayed. can be dispensed until the maintenance Touch the sensor control. programmes have to be run. ...
Settings Factory defaults Demo mode (showroom programme) You can reset the coffee machine to its factory default settings. Do not activate this setting for domestic use. The following will not be reset: The Showroom programme function - The number of drinks dispensed enables the coffee machine to be and the appliance status (No.
Cleaning and care Risk to health due to inadequate cleaning Heat and moisture inside the coffee machine can cause coffee residues to become mouldy and/or milk residues to go off and pose a risk to health. Carefully clean the coffee machine regularly. Overview of cleaning intervals Recommended frequency What do I have to clean / maintain?
Cleaning and care - Waste container Cleaning by hand or in the dishwasher - Water container The brew unit is not dishwasher - Central spout (without stainless steel cover) safe. Clean the brew unit by hand only - Ground coffee chute cover under warm running water.
Cleaning and care - Sharp metal scrapers Unsuitable cleaning agents - Steel wool or stainless steel wire Contact with unsuitable cleaning scourers agents can alter or discolour all surfaces. All surfaces are susceptible Waste container, drip tray and to scratching. Scratches on glass drip tray cover can in some circumstances lead to breakage.
Cleaning and care Remove drip tray cover and lower Cleaning the water container panel . Clean the water container every day. Clean all parts thoroughly. Make sure that the valve, the Clean the lower panel by hand only underside of the water container and using hot water, a little washing up the surface under the water liquid and a soft cloth.
Cleaning and care Removing and cleaning the Central spout water container filter Clean the central spout’s stainless Clean the water container filter once a steel cover by hand only, using month. warm water and a little washing-up liquid. The water container filter is located under the water container.
Cleaning and care Fit the dispensing unit back together. Refit the dispensing unit onto the central spout. Press firmly to ensure the dispensing unit is securely fitted without any gaps. Replace the stainless steel cover and connect the milk pipework if required. Milk pipework ...
Dry all surfaces with a soft cloth. disconnect it from the power supply before cleaning the bean container. Tip: You can also clean the appliance casing with the Miele all purpose Coffee beans contain oils which can microfibre cloth. deposit on the walls of the bean...
The milk pipework can become blocked subsequent damage. by milk residues. The milk pipework It is available to order via the Miele should therefore be rinsed regularly. If a webshop, the Miele Customer Service drink has been made using milk, the...
Carrying out the cleaning process: We recommend using Miele cleaning tablets to clean the brew unit. These have been specially developed for degreasing the brew unit in Miele coffee machines and prevent subsequent damage. The cleaning tablets are available to...
Page 48
Cleaning and care Cleaning the brew unit and interior Clean the brew unit by hand only with warm water. Do not use any cleaning agents. The moving parts of the brew unit are lubricated. Cleaning agents will damage the brew unit. To ensure good tasting coffee and to prevent the formation of microbes in the machine, remove and clean the...
Cleaning and care Follow the further instructions given Tip: Use your vacuum cleaner to remove dry ground coffee residues. in the display. The cleaning process is complete when Dropping a cleaning tablet into the the drinks menu appears. brew unit Insert the brew unit with a cleaning tab in it Descaling the machine and close the machine...
Page 50
You can switch the coffee machine off if Miele descaling tablets are available to you do not want to carry out the order via the Miele webshop, from the descaling programme at this point in Miele Customer Service Department time. You can not make any drinks until (see the end of this booklet for contact the machine has been descaled.
Page 51
Cleaning and care When Rinse the water container and fill with fresh tap water up to the symbol appears in the display: Remove the water container and rinse it thoroughly with clean water. Ensure that no descaling solution residue remains in the water container.
Transporting the machine If you are not going to use the coffee Danger of burning and scalding machine for an extended period of time, on the dispensing spouts. e.g. whilst on holiday, or if it needs to Hot steam can cause scalding. be moved, a number of procedures will Keep well away from the area need be carried out to ensure its safety.
Follow the instructions which appear in the display to remedy the problem. If after this, the fault message appears in the display again, contact Miele Service. Problem Cause and remedy F1, F2, There is an internal fault.
Page 54
Problem solving guide Problem Cause and remedy F73 or The brew unit cannot be positioned correctly. Check the brew unit Switch the coffee machine off with the On/ Off button . Switch off at the wall socket and unplug the coffee machine.
Page 55
Problem solving guide Problem Cause and remedy Too much ground coffee There is too much ground coffee in the coffee chute. The brew unit cannot compact ground coffee if more than two level spoonfuls of ground coffee are added to the coffee chute. The ground coffee will be emptied into the waste container and the fault message will appear in the display.
Switch off at the wall socket and unplug the coffee machine. Contact a qualified electrician or the Miele Customer Service Department. The coffee machine The factory set switch-off time (20 minutes) or the turns off suddenly.
Page 57
Problem solving guide Problem Cause and remedy The water container is Droplets of water have settled between the water empty. container and the side walls of the casing, or this Fill and replace the water container has not area is damp (see illustration). appeared in the display.
Page 58
Problem solving guide Problem Cause and remedy After switching on the This is not a fault. machine the message When the drip tray and waste container are Empty the drip tray and the emptied, the internal counter is not reset after the waste container appears coffee machine has been switched off.
Page 59
Problem solving guide Problem Cause and remedy Fill the bean container This is not a fault. pears in the display Confirm the message with OK. even though the bean Insufficient coffee beans are getting into the grinder. container has just been Have you used a dark roast? filled.
Page 60
Problem solving guide Problem Cause and remedy The descaling process The descaling programme cannot be stopped once was started inadvert- OK has been touched. ently. It must now be completed through to the end. This is a security setting to fully descale the coffee machine. It ensures a long service life and that your coffee machine is functioning correctly.
Page 61
Problem solving guide Problem Cause and remedy Coffee grounds have This is not a fault. settled on the lid of the The movement of the brew unit during the brewing drip tray and in the in- process can cause some ground coffee to fall terior around the brew around it.
Problem solving guide Unsatisfactory results Problem Cause and remedy The coffee is not hot The cup has not been pre-heated. enough. The smaller the cup and the thicker its sides, the more important it is to pre-heat it. Pre-heat the cup, for example, with hot water. The brewing temperature has been set too low.
Page 63
Problem solving guide Problem Cause and remedy The coffee grinder The coffee bean container has become empty during makes a louder noise the grinding process. than usual. Fill the coffee bean container with fresh beans. There may be foreign objects such as plastic or stones in amongst the coffee beans.
Contact in the event of a fault In the event of any faults which you cannot remedy yourself, please contact your Miele dealer or the Miele Customer Service Department. You can book a Miele Customer Service Department call-out online at www.miele.com/service.
After sales service and warranty Warranty For information on the appliance warranty specific to your country please contact Miele. See back cover for address. In the UK, your appliance warranty is valid for 2 years from the date of purchase. However, you must activate your cover by calling 0330 160 6640 or registering online at www.miele.co.uk.
Saving energy The following tips can help you save energy and money as well as care for the environment: - Operate the coffee machine in Eco mode (default setting). - The coffee machine’s energy consumption may increase if you change the settings for the timer. appears in This setting uses more energy the display.
If the mains connection cable is damaged, it must only be replaced with a specific mains connection cable of the same type (available from the Miele Customer Service Department). For safety reasons, such replacement may only be carried out by a qualified specialist or the Miele Customer Service Department.
*INSTALLATION* Installation If the machine is installed in a niche, the Danger of overheating due to niche must provide the following insufficient ventilation. minimum dimensions: If the coffee machine is not sufficiently ventilated, the appliance Height 510 mm can overheat. Width 450 mm Please ensure that there is adequate...
Technical data Electricity consumption in standby < 0.5 Watt mode (default setting): Pump pressure: max. 15 bar Through-flow heater: 1 stainless steel thermo block Dimensions (W x H x D): 241 x 360 x 460 mm Net weight: 9.48 kg Connection cable length: 120 cm Water container 1.3 l capacity: Bean container 200 g capacity: Waste container max. 7 portions of coffee grounds capacity: Central spout: Height adjustable from 80–135 mm...
Need help?
Do you have a question about the CM 5310 and is the answer not in the manual?
Questions and answers