Subscribe to Our Youtube Channel
Related Manuals for Hans Grohe Axor Cittterio 39447 1 Series
Summary of Contents for Hans Grohe Axor Cittterio 39447 1 Series
- Page 1 Installation Instructions / Warranty Cittterio 39447XX1 cross handles 39448XX1 lever handles...
-
Page 2: Technical Data
Citterio Tub Filler with Handspray 39447XX1 Cross handles 39448XX1 Lever handles Technical Data Maximum incoming water pressure 145 psi Recommended indoming water pressure 14.5 - 72 psi Recommended incoming hot water temp F - 140 Handshower flow rate 2.5 gpm Spout flow rate 5.8 gpm Backflow prevention provided by automatically resetting diverter and check valve in... -
Page 3: Installation Instructions
Recommended Tools (not included) 12 mm deep socket 17 mm deep socket 12 mm allen wrench Teflon thread tape Waterproof bathroom sealant suitable for the wall surface Cutting tools Installation Instructions Remove the caps from the plaster shields. Cut • the plaster shields so that they extend 1 mm (1/ 16") outside surface of the finished wall. - Page 4 Measure the distance from the spout outlet to the • end of the plaster shield. Record this measurement (“X”). Add 1 7/8" to “X”. Measure the spout connector. Mark a point X + • 1 7/8" from the end. Cut the spout connector at this point.
- Page 5 Measure and mark the inner sleeves at a point • ½” outside the surface of the finished wall. Remove the inner sleeves. Cut them at this point. Push them back onto the stems. Push the handle into place over the hot and cold •...
- Page 6 If the handle is still not straight, remove the • insert. Use a Philips screwdriver to loosen the handle screw 3 complete turns. Pull the lever up from the rest of the handle • assembly. Turn it approximately 60°. Push it back down.
- Page 7 Place the hot and cold flanges against the wall. • Push the handles into place. Rotate the handle barrels clockwise to screw the handles into place. Place the spout flange over the spout connector • and agains the wall. Push the spout into place. Tighten the spout set screw.
- Page 8 Install a black rubber hose washer to one end of • the handshower hose. Screw it to the handshower outlet on the bottom of the spout. Place the screen washer in the other end of the hose. Attach it to the handshower. Sit the handshower in the holder.
-
Page 9: Replacement Parts
Replacement Parts lever handle 39396XXX cross handle 39295XXX spout 97704XXX shower holder 97705XXX hot flange 96755XXX cold flange 96754XXX spout flange 96756XXX shower holder flange 97716XXX shower holder assembly 97716XXX 10 aerator 13956000 11 diverter knob 96466XXX 12 mounting kit 96392000 13 hot cartridge 39448XXX... - Page 10 Cleaning Recommendation for Hansgrohe Products Modern faucetry and shower products utilize a combination of materials to comply with the needs of the market with regard to design and functionality. To avoid damage, it is necessary to use some caution when cleaning. Damage caused by improper treatment is not covered under the Hansgrohe warranty.
- Page 11 THIS WARRANTY DOES NOT COVER, AND HANSGROHE WILL NOT PAY FOR: Conditions, malfunctions or damage not resulting from defects in material or workmanship. Conditions, malfunctions or damage resulting from (1) improper installation, improper maintenance, misuse, abuse, negligence, accident or alteration, or (2) the use of abrasive or caustic cleaning agents or “no rinse” cleaning products, or the use of the product in any manner contrary to the product instructions.
- Page 12 Hansgrohe, Inc. 1490 Bluegrass Lakes Parkway Alpharetta, GA 30004 • • Tel. 770 360-9880 Fax 770 360 9887 • www.hansgrohe-USA.com...
Need help?
Do you have a question about the Axor Cittterio 39447 1 Series and is the answer not in the manual?
Questions and answers